Hello!
I just upgraded from 7.10 to the latest alpha release, and now I cant get my pvr-usb2 to work. It does not seem to load properly.
Dmesg:
22.805068] Linux video capture interface: v2.00
[ 22.948966] usbcore: registered new interface driver pvrusb2
[ 22.949011] pvrusb2: Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner : V4L in-tree version
[ 22.949014] pvrusb2: Debug mask is 31 (0x1f)
[ 23.146009] cx25840' 0-0044: cx25843-24 found @ 0x88 (pvrusb2_a)
[ 23.341202] tuner' 0-0043: chip found @ 0x86 (pvrusb2_a)
[ 23.368250] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 23.368273] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 23.461352] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input5
[ 23.496897] tda9887 0-0043: creating new instance
[ 23.496901] tda9887 0-0043: tda988[5/6/7] found
[ 23.497048] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 23.508087] tuner' 0-0061: chip found @ 0xc2 (pvrusb2_a)
[ 23.511701] wm8775' 0-001b: chip found @ 0x36 (pvrusb2_a)
[ 23.524585] tveeprom 0-00a2: Hauppauge model 24019, rev C289, serial# 8567676
[ 23.524590] tveeprom 0-00a2: tuner model is TCL MFPE05 2 (idx 89, type 38)
[ 23.524594] tveeprom 0-00a2: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74)
[ 23.524597] tveeprom 0-00a2: audio processor is CX25843 (idx 37)
[ 23.524600] tveeprom 0-00a2: decoder processor is CX25843 (idx 30)
[ 23.524603] tveeprom 0-00a2: has radio, has IR receiver, has no IR transmitter
[ 23.524610] pvrusb2: Supported video standard(s) reported available in hardware: PAL-B/B1/D/D1/G/H/I/K;SECAM-B/D/G/H/K/K
[ 23.524616] pvrusb2: Mapping standards mask=0xff00ff (PAL-B/B1/D/D1/G/H/I/K;SECAM-B/D/G/H/K/K1/L/LC)
[ 23.524619] pvrusb2: Setting up 20 unique standard(s)
[ 23.524624] pvrusb2: Set up standard idx=0 name=PAL-B/G
[ 23.524627] pvrusb2: Set up standard idx=1 name=PAL-D/K
[ 23.524630] pvrusb2: Set up standard idx=2 name=SECAM-B/G
[ 23.524632] pvrusb2: Set up standard idx=3 name=SECAM-D/K
[ 23.524635] pvrusb2: Set up standard idx=4 name=PAL-B
[ 23.524638] pvrusb2: Set up standard idx=5 name=PAL-B1
[ 23.524640] pvrusb2: Set up standard idx=6 name=PAL-G
[ 23.524643] pvrusb2: Set up standard idx=7 name=PAL-H
[ 23.524646] pvrusb2: Set up standard idx=8 name=PAL-I
[ 23.524648] pvrusb2: Set up standard idx=9 name=PAL-D
[ 23.524651] pvrusb2: Set up standard idx=10 name=PAL-D1
[ 23.524653] pvrusb2: Set up standard idx=11 name=PAL-K
[ 23.524656] pvrusb2: Set up standard idx=12 name=SECAM-B
[ 23.524659] pvrusb2: Set up standard idx=13 name=SECAM-D
[ 23.524661] pvrusb2: Set up standard idx=14 name=SECAM-G
[ 23.524664] pvrusb2: Set up standard idx=15 name=SECAM-H
[ 23.524667] pvrusb2: Set up standard idx=16 name=SECAM-K
[ 23.524669] pvrusb2: Set up standard idx=17 name=SECAM-K1
[ 23.524672] pvrusb2: Set up standard idx=18 name=SECAM-L
[ 23.524675] pvrusb2: Set up standard idx=19 name=SECAM-LC
[ 23.524678] pvrusb2: Initial video standard auto-selected to PAL-B/G
[ 23.524690] pvrusb2: Device initialization completed successfully.
[ 23.524921] pvrusb2: registered device video0 [mpeg]
[ 23.525005] pvrusb2: registered device radio0 [mpeg]
[ 23.533495] firmware: requesting v4l-cx25840.fw
It does seem to load but then it requests the firmware again? Does anyone know how to fix this? I found a workaround for pvr-usb2 for earlier kernels but that does not work on 2.6.27-14.
/Per
