Remote Codes Issue HT-CT150

[CentralMedia]

Morning

I bought a Sony HT-CT150 sound bar, was on sale.

Created a device and started with learning the IR codes. Unfortunately the learning function on my setup seems to be giving issues, the USBUIRT does not respond. Thus I am like ok, have another one, which I stuck into my laptop, install the windows drivers and downloaded the lrnhelper from the site.

The codes learned fine in lrnhelper, when you test from there also, the device responded, but when I put these codes into the device template, the device does not respond. Lrnhelper is learning the codes in pronto format.

Any ideas or thoughts, I checked the DCEROUTER.log and its sending the correct codes.

[tschak909]

Is this in 10.04 or 12.04 ?

-Thom

[RayBe]

Did you assign your newly created device template to the room in which you are using the USBUIRT?
When I was making a device template I did not and my USBUIRT was also not responding.

Br,
Raymond

[CentralMedia]

Its 10.04

The device was not assigned to a room, but the corresponding USBUIRT for controlling it was assigned when creating the device.

I have the USBUIRT connected to distribution block, with emitters, which control my TV, Directv box and well hopefully this, you see the flashes when the code is transmitted.

[CentralMedia]

Do know if this will help

But I watched the flash from the USBUIRT connected to the CORE and in comparison with that from Learn Helper, the flash seems to be only repeating 2 times, not the 4 for general IR codes. Did this by adjusting the repeat count in Learn Helper and monitored the flash.

if this observation is the issue, how do I fix or work around?

[CentralMedia]

Ok seems that assessment is incorrect, decided to open the template, instead of going through, av equipment and choosing A/V properties. Then I realize that there are double codes for the toggle power and other codes I did not even specify, trying a clean up of the rough oodes and will advise if that helps

[CentralMedia]

Ok, that did not help, seems it still transmitting just a small flash as when I set repeat count to 2 in learn helper, unlike the longer flash through learn helper, when set to 4 as the device template.

Also, I created my own Codeset for the device, but if I go through device templates, it adds additional codes to my Codeset, is there a way to fix this, I only want the ones I added.

[CentralMedia]

Ok got it, found the following

http://wiki.linuxmce.org/index.php/Extending_the_repeat_duration_of_raw_Pronto_IR_codes

Had to quadruple it to, double was insufficient and it worked

0000 0067 0000 0040 0060 0019 0030 0019 0018 0019 0030 0019 0018 0019 0030 0019 0018 0019 0018 0019 0018 0019 0018 0019 0018 0019 0018 0019 0030 0019 0030 0019 0018 0019 0018 0364 0060 0019 0030 0019 0018 0019 0030 0019 0018 0019 0030 0019 0018 0019 0018 0019 0018 0019 0018 0019 0018 0019 0018 0019 0030 0019 0030 0019 0018 0019 0018 0364 0060 0019 0030 0019 0018 0019 0030 0019 0018 0019 0030 0019 0018 0019 0018 0019 0018 0019 0018 0019 0018 0019 0018 0019 0030 0019 0030 0019 0018 0019 0018 0364 0060 0019 0030 0019 0018 0019 0030 0019 0018 0019 0030 0019 0018 0019 0018 0019 0018 0019 0018 0019 0018 0019 0018 0019 0030 0019 0030 0019 0018 0019 0018 0364

Original Code is

0000 0067 0000 0010 0060 0019 0030 0019 0018 0019 0030 0019 0018 0019 0030 0019 0018 0019 0018 0019 0018 0019 0018 0019 0018 0019 0018 0019 0030 0019 0030 0019 0018 0019 0018 0364