Silly AV Wizard

[torabian]

Ok, so I built the box, I rebooted, I got the twinkly array of AV Wizard noises followed by black screen.

Hit 2  -twinkly beep beep, black screen. Hit 7, twinkly beep beep, black screen. 2,6 twinkly beep beep, black screen. Getting the picture? because I'm sure not going to.

Using VGA, monitor definitely supports both resolutions.

I am using an NVidia Ti4800SE with UI2. I know 4xxx is not supported but worked fine in 1.1 Also works fine if I swap to another TTY, fire up xwindows and run the linuxmce startup sequence (even runs and completes the damn AV Wizard).

Save the settings, reboot the system..... twinkly beep beep ----- black screen


Ahhhhhhhhhhhhhhhhhhhhhhhhhhh

[Zaerc]

http://wiki.linuxmce.org/index.php/AVWizard#How_A.2FV_Wizard_Starts
http://wiki.linuxmce.org/index.php/Display_Drivers#X-windows_won.27t_start_for_AVWizard

[torabian]

Thanks for the reply Zaerc.

I already changed the display config using dpkg-reconfigure but there might be something useful in the troubleshooting guide which I hadn't seem before

[totallymaxed]

Ok, so I built the box, I rebooted, I got the twinkly array of AV Wizard noises followed by black screen.

Hit 2  -twinkly beep beep, black screen. Hit 7, twinkly beep beep, black screen. 2,6 twinkly beep beep, black screen. Getting the picture? because I'm sure not going to.

Using VGA, monitor definitely supports both resolutions.

I am using an NVidia Ti4800SE with UI2. I know 4xxx is not supported but worked fine in 1.1 Also works fine if I swap to another TTY, fire up xwindows and run the linuxmce startup sequence (even runs and completes the damn AV Wizard).

Save the settings, reboot the system..... twinkly beep beep ----- black screen


Ahhhhhhhhhhhhhhhhhhhhhhhhhhh

As Zaerc suggested above I would follow the suggestions here in section 3.1 ; http://wiki.linuxmce.org/index.php/Display_Drivers#X-windows_won.27t_start_for_AVWizard

Also it might be worth posting the video related settings that you have in Web Admin ->Wizard -> Devices -> Media Directors for the MD at the Core/Hybrid ie the following;

Connector        
Video settings    
TV Standard
Video Card

Regards


Andrew

[Stingly]

Using VGA, monitor definitely supports both resolutions.

I am using an NVidia Ti4800SE with UI2.

Is your cable plugged into the DVI or VGA port on the card? Plug it into the DVI one, even if you need to use a converter. I have this card and it took me ages to work this out! It uses the DVI port as the default output! I don't know how to change it though...

[torabian]

Stingly,

Good tip. I have been trying to change the output to VGA using the CRTx connected monitor card, but no joy. I'm going to take my PC round to my brothers and plug the DVI into his TV. If it does then its LCD TV time.

Not sure why the DVI is the default for this card. Says in the docs that VGA is assumed because most people will be using a PC monitor.

[tschak909]

for NVidia cards with a DVI port, and a VGA port, the DVI port is always the default port. attach a DVI to VGA adaptor.

also, why are you using that card? I would recommend very insanely strongly to get a 6xxx series card.

-Thom

[Stingly]

I'm personally using it cos it was in an old machine that I've been testing LMCE on. When I get serious, I'll buy all new hardware and make a kick ass system, but until then its "make it work for as cheap as possible"!