Author Topic: Hi everyone!  (Read 2842 times)

cbock35

  • Making baby steps
  • Posts: 3
    • View Profile
Hi everyone!
« on: March 26, 2009, 10:04:30 pm »
Hey folks. My name's Chris. I've been checking the board, wiki and docs out for the last few days. I have been a MythTV user on and off since 0.14. Unfortunately, I've had some odd HW failures with my Myth setups.  :( I was getting ready to rebuild and decided I should give LMCE a shot first! I've dabbled in Linux for about 10years now. So, I'm relatively comfortable with what needs to happen to get my system up and running. Right now I'm battling thru a simple Kubuntu install on my ASUS m3n78-vm board. From what I've read, I should be able to get it running properly with a couple tweaks.

Anyhow, I just wanted to say hello. I'm looking forward to getting this project of mine off the ground.  :)

colinjones

  • Alumni
  • LinuxMCE God
  • *
  • Posts: 3003
    • View Profile
Re: Hi everyone!
« Reply #1 on: March 27, 2009, 12:21:00 am »
Hello!

Before plunging in, have you read the FAQs, hardware requirements, network requirements and recommended installation path? It would save you a huge amount of time and hassle if you did that research thoroughly, first. There are a lot of pitfalls if you just plunge in.

There are some limitations on the hardware you can use. And the network design usually trips up people - http://wiki.linuxmce.org/index.php/Network_Setup

totallymaxed

  • LinuxMCE God
  • ****
  • Posts: 4660
  • Smart Home Consulting
    • View Profile
    • Dianemo - at home with technology
Re: Hi everyone!
« Reply #2 on: March 27, 2009, 01:05:39 am »
Hey folks. My name's Chris. I've been checking the board, wiki and docs out for the last few days. I have been a MythTV user on and off since 0.14. Unfortunately, I've had some odd HW failures with my Myth setups.  :( I was getting ready to rebuild and decided I should give LMCE a shot first! I've dabbled in Linux for about 10years now. So, I'm relatively comfortable with what needs to happen to get my system up and running. Right now I'm battling thru a simple Kubuntu install on my ASUS m3n78-vm board. From what I've read, I should be able to get it running properly with a couple tweaks.

Anyhow, I just wanted to say hello. I'm looking forward to getting this project of mine off the ground.  :)

Hi and welcome;

The only thing that springs to mind about the m3n78-vm is that the audio seemed to be a little difficult to get right. We've moved away from AMD boards currently so I cant give you much more detail... look in the motherboard section of the Wiki when choosing a motherboard is good advice - http://wiki.linuxmce.org/index.php/Category:Mainboards

All the best

Andrew
Andy Herron,
CHT Ltd

For Dianemo/LinuxMCE consulting advice;
@herron on Twitter, totallymaxed+inquiries@gmail.com via email or PM me here.

Get Dianemo-Rpi2 ARM Licenses http://forum.linuxmce.org/index.php?topic=14026.0

Get RaspSqueeze-CEC or Raspbmc-CEC for Dianemo/LinuxMCE: http://wp.me/P4KgIc-5P

Facebook: https://www.facebook.com/pages/Dianemo-Home-Automation/226019387454465

http://www.dianemo.co.uk

cbock35

  • Making baby steps
  • Posts: 3
    • View Profile
Re: Hi everyone!
« Reply #3 on: March 27, 2009, 01:45:14 am »
Thank you for the warm welcomes. :)

Yes, colinjones, I have read A LOT over the last few days.  I hope I didn't come off as someone who was just "jumping in". As far as the network goes, I think I've got that covered too. I've got a Wirless N+ router for my LAN, two NICs for the core's mb. And, a 8 port gigabit switch for the LMCE-LAN. Plus, lots of CAT6.

totallymaxed, I do remember reading about an issue with the audio from that mb. But, I should be able to work around that. I already have the board. I don't intend on buying a replacement one unless I find insurmountable problems. I'll know soon enough.