add X10 CM11A in lMCE710

[poyon]

Hello,

I am trying to integrate a CM11A to control my light module with LinuxMCE.

I added the CM11A in interface and the parnet is the CORE.
It don't work. This is the message in the log of CM11 :

10      02/05/08 23:48:20.213           Receive string: MESSAGE 82             <0xb70f0b90>
10      02/05/08 23:48:20.213           Received MESSAGE 82             0x806ca10 device: 19 <0xb70f0b90>
10      02/05/08 23:48:20.213           Received Message type 1 ID 760 from 0 to 19 (device: 19) resp 0 <0xb70f0b90>
10      02/05/08 23:48:20.214           Could not find a handler for message - from 0 to 19 Type: 1 ID: 760 (device: 19) Command_Impl1 Dev #19 <0xb70f0b90>

[Zaerc]

Have you looked at: http://wiki.linuxmce.org/index.php/CM11?

I'm not having any problems with my CM11 under 0710 BETA3, and as far as I can see you can't do much wrong other then not configuring the right serial port ("COM Port on PC"). 

[cobradevil]

I have also problems with lmce keeping the cm11a controller on the right port.

When i wait ten minutes after setting the com port + reload router then i don't get any messages but the com port is unselected so i have to select it again (device disabled).

With kind regards,

William van de Velde

[nite_man]

Have you looked at: http://wiki.linuxmce.org/index.php/CM11?

I'm not having any problems with my CM11 under 0710 BETA3, and as far as I can see you can't do much wrong other then not configuring the right serial port ("COM Port on PC"). 

What about problem with bad checksum:

Code: [Select]

10      02/10/08 21:18:38.769           Sending address with HouseCode=6, DeviceCode=6. <0x41802950>
10      02/10/08 21:18:38.769           Sending packet with HighByte=4, LowByte=66. <0x41802950>
10      02/10/08 21:18:38.769           Sending header with Checksum: 6a. <0x41802950>
10      02/10/08 21:18:42.677           Got response: 5a from CM11A. <0x41802950>
01      02/10/08 21:18:42.677           Bad checksum received (send:6a, recieved:5a)Have you found the way to solve that?

[Zaerc]

Have you looked at: http://wiki.linuxmce.org/index.php/CM11?

I'm not having any problems with my CM11 under 0710 BETA3, and as far as I can see you can't do much wrong other then not configuring the right serial port ("COM Port on PC"). 

What about problem with bad checksum:

Code: [Select]

10      02/10/08 21:18:38.769           Sending address with HouseCode=6, DeviceCode=6. <0x41802950>
10      02/10/08 21:18:38.769           Sending packet with HighByte=4, LowByte=66. <0x41802950>
10      02/10/08 21:18:38.769           Sending header with Checksum: 6a. <0x41802950>
10      02/10/08 21:18:42.677           Got response: 5a from CM11A. <0x41802950>
01      02/10/08 21:18:42.677           Bad checksum received (send:6a, recieved:5a)Have you found the way to solve that?

Well, it's more of a workaround... I don't use sensors or X10 remotes.   But I guess that doesn't really help you.  

[nite_man]

Well, it's more of a workaround... I don't use sensors or X10 remotes.   But I guess that doesn't really help you.  

Trying to figure out why this bug still exists. Sure X10 is old and definitely not perfect. But people still use it and IMHO it'd be nice to have 100% working X10 interface. Unfortunately,  I'm not C++ guru. So, I'm afraid it might take a lot of time to patch the code by my self.