61
Developers / Re: Device Spawning
« on: February 23, 2013, 04:05:19 pm »
Alright I'm going to do an install of the latest snap and see if it works there. I have poked around a lot with this one. So maybe...
News:
Rule #1 - Be Patient - Rule #2 - Don't ask when, if you don't contribute - Rule #3 - You have coding skills - LinuxMCE's small brother is available: http://www.agocontrol.com
LinuxMCE sponsor
open.home.automation
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
62
Developers / Re: Device Spawning
« on: February 22, 2013, 10:55:39 pm »
It still does not start on its own.
63
Developers / Re: Device Spawning
« on: February 22, 2013, 10:16:35 pm »
Thanks Thom, I had it as controlled via Computers in the template and switched it to Core and still will not start on its own. Device shows controlled by Core.
64
Developers / Re: Device Spawning
« on: February 22, 2013, 01:09:23 pm »
posde: bash -x works but once I close the terminal it stops then will not start on its own after reload. If I detach using & at the end I can close the terminal but I will not start on its own after reboot.
Thom I did copy it to /usr/pluto/bin. That's where I'm running it from.
Thanks
Thom I did copy it to /usr/pluto/bin. That's where I'm running it from.
Thanks
65
Developers / [Solved] Device Spawning
« on: February 22, 2013, 02:14:41 am »
Hello,
I created a device template I wrote in c++. This is my 1st venture with c++ so I'm just starting out there (and I don't think I'll ever get my head fully around pointers). That said the program works fine. I can start the device from a terminal using "Spawn_Device.sh" and the device runs as expected. My problem is I cannot get the device to spawn on its own. I even wrote a pnp script to see if that worked (and that was... interesting). The device template loaded correctly but did not start, even after several reloads and reboots. So while I usually enjoy delving deeper into lmce to see why it works and why not, this ones getting me. Any insite as to why this would be?
Thanks
Jim
I created a device template I wrote in c++. This is my 1st venture with c++ so I'm just starting out there (and I don't think I'll ever get my head fully around pointers). That said the program works fine. I can start the device from a terminal using "Spawn_Device.sh" and the device runs as expected. My problem is I cannot get the device to spawn on its own. I even wrote a pnp script to see if that worked (and that was... interesting). The device template loaded correctly but did not start, even after several reloads and reboots. So while I usually enjoy delving deeper into lmce to see why it works and why not, this ones getting me. Any insite as to why this would be?
Thanks
Jim
66
Users / Re: RAID question
« on: February 07, 2013, 01:27:15 am »
It recognized mine fine. I went through install and once complete it prompted me to use the devices. Data was fine. I did back it up before just in case. Make sure you chose the correct location for the install. I did not once and broke the raid. I was able to salvage the data but what a pain.
67
Users / Re: Southern California Linux Expo
« on: January 17, 2013, 04:09:49 pm »
posde,
Just gave 150 EUR. Let me know if you fall short.
Have fun!
Just gave 150 EUR. Let me know if you fall short.
Have fun!
68
Users / Re: MAC: Boot an Install from DVD
« on: January 01, 2013, 09:20:03 pm »
Mine is x86 or pc based. Intel I5. Also my dell laptop in a vm. Not sure what that has for CPU. But it does happen on usb dvd. I never checked to see if it was hanging or just not displaying.
Safe travels
Safe travels
69
Developers / Re: Disabling the on screen orbiter.
« on: January 01, 2013, 12:51:46 am »
Hey Thom,
Quote
golgoj4 was a building contractor, just two years agoI just noticed that. I am still a construction contractor. I'm getting a pretty good handle on c++. I'm converting some GSD devices I have written in Ruby.
70
Users / Re: Will a Dell Optiplex GX280 work as a headless core?
« on: December 31, 2012, 02:59:06 pm »
I have 3 usb hubs with no problems. I also have usb to rs232 converters if you run out of card space.
71
Users / Re: LMCE - I want to do it correctly this time - Z-Wave and MythTV
« on: December 31, 2012, 01:41:47 am »
I have a HVR-2250 and it is kind of a pain to get working. I developed a script to get it working as I kept forgetting. The only thing is that I don't think that Steve Toth is supporting the driver anymore. I have not been able to find it after he changed his website.
72
Users / Re: Will a Dell Optiplex GX280 work as a headless core?
« on: December 31, 2012, 01:25:19 am »
I had my core running on some very old stuff and never had any issues. It's really the new stuff that we run into problems. With headless core just about everything works. You will need a 2nd nic though.
73
Developers / Re: Disabling the on screen orbiter.
« on: December 26, 2012, 02:36:38 am »
I have read through some. Will take a good look now. Thanks for the help.
Thanks
Jim
Thanks
Jim
74
Developers / Re: Disabling the on screen orbiter.
« on: December 26, 2012, 01:42:12 am »
I agree. I will learn. You have something for me to screw around with? i usually monitor irc.
75
Developers / Re: Disabling the on screen orbiter.
« on: December 26, 2012, 01:16:52 am »
Sorry Thom. PHP, Javascript, jquery, some java and less C++ but I'm learning. But was very good at fortran 25+ yrs ago