Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - huh

Pages: 1 2 3 [4] 5 6 ... 17
46
Users / Re: Funding Drive: ZWave Door Locks
« on: September 23, 2012, 09:36:20 pm »
I'll pledge E25,- for the z-wave doorbel.

I just matched your E25- let's make this pig fly.

47
Users / Re: Funding Drive: ZWave Door Locks
« on: September 21, 2012, 06:49:53 pm »
James (but not Bond)


That's rather presumptuous...

I may actually use the doorbell, any idea on a cost?

48
Users / Re: Funding Drive: ZWave Door Locks
« on: September 19, 2012, 03:14:58 pm »

49
Users / Re: Funding Drive: ZWave Door Locks
« on: September 17, 2012, 10:58:10 pm »
I'll match your 50 euro too.  PM where to send the money...  Ideally Paypal.

50
Users / Re: Asterisk + Google Voice
« on: August 23, 2012, 05:23:02 am »
I too am interested in getting this working.  There is an open trac ticket

51
Users / Re: Android QOrbiter
« on: July 27, 2012, 05:56:36 am »
I'm having trouble with my touchpad as well- qorbiter is grabbing device id "45" even through only have qorbiter devices "56" and "75".  I don't have a device 45 or anything really even close.  On one occasion, I was able to halt the qorbiter starting and was able to type in "56" as my device id.  I hitting "go" changed the button color to green, but then the app froze.

Any thoughts or suggestions?

52
Developers / Re: QOrbiter: Updated
« on: July 18, 2012, 02:10:53 pm »
Updated the nightly, please try that and let me know if you encounter errors. I tested it before i posted so im a bit confused as to why it went fubar

-golgoj4

Sweet- good job!  Just pulled it down a minute ago from your site, fixes the error for me.  ICS on Samsung galaxy s2

53
Developers / Re: QOrbiter: Updated
« on: July 18, 2012, 05:14:08 am »
"Your application encountered a fatal error and cannot continue." every time I start it.

I an having the same experience, 1004.

54
Users / Re: 1004: The time has come.
« on: May 14, 2012, 04:29:08 pm »
Zsync is failing for me... anyone else had success with zsync?

I had a similar experience and played with it a little before assuming I was doing something wrong and instead pulled down a new file.

I tried 25964 and am still getting the failed to startup x on my nvidia geforce 5200 laptop.  Multiple reboots and deleted the /etc/X11/xorg.pluto.* did not help.  Left it on the failed to startup x screen and tried to boot a MD hoping to get somewhere with that, but as that the core was no where near setup (did not go through any of the setup wizards) the MD got stuck in a reboot loop.  Looking at flowers with the wife later tonight, but will try to jump on IRC soon.

55
Users / Re: 1004: The time has come.
« on: May 11, 2012, 07:20:18 am »
but if nobody gives a poo I am comfortable with where they are...

Well, as that you offered, my shih tzu's could use some more uniforms!  My vote, however, is to encourage you to keep pushing this further and let us keep testing these so it really gets to the point that you put in the DVD, press a couple keys and a little while later are on your way to a smart house.

56
Users / Re: 1004: The time has come.
« on: May 11, 2012, 05:49:36 am »

Is anyone else even testing these on a regular basis?

Yes.  And just burning *5955 now to test.

57
Users / Re: TNJ Files!
« on: March 29, 2012, 03:33:30 am »
Digging up an old topic, but just ran into this...  have family photos on a DNS-323 located on the internal network- not using LMCE file structure.  For the approximately 30,000 pictures, LMCE created about 930 MB of *.tnj files.

58
Users / Re: VIDEO CARDS: ATI, Intel, VIA... whatever you got...
« on: March 24, 2012, 07:09:30 am »
Dell Latitude C400, ui2 with alpha is a little laggy, so went to ui2 w/o alpha...  about 1/2" of what should have been the far right of the display was displaced on the left hand side.  Will run through AVWizard again later..  output of 'lspci -v | grep "VGA"'

00:02.0 VGA compatible controller: Intel Corporation 82830 CGC [Chipset Graphics Controller] (rev 04)

59
Users / Re: 1wire support
« on: March 03, 2012, 01:47:27 am »
No idea what happened...  reinstalled LMCE a couple times since previous posts and currently have an install where the 1wire was discovered as discussed in the wiki.  I wasn't expecting the child to be found, so wasn't really paying attention to the time between plugging in the sensor and when the log file discovered the device.  Thinking back, I probably should have checked the time stamps.  duh.  If I were to guess, probably 10 minutes or so.

For the sake of a record, I have this device:  http://www.ibuttonlink.com/linkusbi.aspx   (LinkUSBi if the URL changes) and five of their temperature sensors:  http://www.ibuttonlink.com/t-sense.aspx

All (5) sensors were detected as children and were approximately reading the same temperature...  so, I've gone and started to play with it.  Currently removed all but (1) sensor which I put in my attic.  I've rotated the sensors out to see what would happen and it appears that the temperature reported remains static on the "missing" thermistors.  Very cool that it appears that the rest continue to function properly when one is lost.

60
Developers / Re: Findings while working on alternative install DVD...
« on: February 29, 2012, 01:09:38 am »
So I can test creating an Install image with that script?

I would like to know this as well...  Need to redo my install and the wife is not relying on lmce at the moment, so would be a good time to be an alpha/beta tester.  About to cook dinner, so just going to try and see what happens.

Pages: 1 2 3 [4] 5 6 ... 17