Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - ajdaniels63

Pages: [1]
Installation issues / Re: Asus M3N78-VM Audio via HDMI use to work
« on: June 08, 2010, 05:51:55 pm »
Everything is unmuted. Still no sound.


Installation issues / Re: Asus M3N78-VM Audio via HDMI use to work
« on: June 08, 2010, 02:55:03 pm »
I ran alsamixer and get the following:

Card: HDA NVidia
Chip: Nvidia MCP77/78 HDMI
blah blah

Something I noticed that is a bit off. Where it use to say IEC958, now it shows it as "S/PDIF, S/PDIF D, and S/PDIF 1" It's never shown that before. It always showed the IEC958, etc...


Installation issues / Asus M3N78-VM Audio via HDMI use to work
« on: June 08, 2010, 04:53:42 am »
I just did a fresh install of the system. My MD's are M3N78-VM and I use to be able to get video and audio via HDMI. Now for whatever reason, it stopped working.

My config is the same as before when it use to work. Here is the parameters:

Alsa: 1.0.23
nvidia: 195 (installs by default)

New install, things I had to change:
For some reason xorg.conf showed "device" as "vesa" and not "nvidia" This fixed my inability to pick U2 (fixed)

I use to just setup the MD and download/compile/install the new alsa via script, go into alsamixer and unmute everything and reboot. Viola, audio over HDMI worked. Now it is not working.

Any idea's anyone? Everything I use to have to change looks right.



Couple screen shots:

root@moon33:~# aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: NVidia [HDA NVidia], device 0: ALC1200 Analog [ALC1200 Analog]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: NVidia [HDA NVidia], device 1: ALC1200 Digital [ALC1200 Digital]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: NVidia [HDA NVidia], device 3: NVIDIA HDMI [NVIDIA HDMI]
  Subdevices: 1/1
  Subdevice #0: subdevice #0

root@moon33:~# aplay -L
    Discard all samples (playback) or generate zero samples (capture)
    HDA NVidia, ALC1200 Analog
    Front speakers
    HDA NVidia, ALC1200 Analog
    4.0 Surround output to Front and Rear speakers
    HDA NVidia, ALC1200 Analog
    4.1 Surround output to Front, Rear and Subwoofer speakers
    HDA NVidia, ALC1200 Analog
    5.0 Surround output to Front, Center and Rear speakers
    HDA NVidia, ALC1200 Analog
    5.1 Surround output to Front, Center, Rear and Subwoofer speakers
    HDA NVidia, ALC1200 Analog
    7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
    HDA NVidia, ALC1200 Digital
    IEC958 (S/PDIF) Digital Audio Output
    HDMI Audio Output

root@moon33:~# cat /proc/asound/version
Advanced Linux Sound Architecture Driver Version 1.0.23.
Compiled on Jun  7 2010 for kernel 2.6.27-17-generic (SMP).
root@moon33:~# cat /proc/asound/devices
  0: [ 0]   : control
  1:        : sequencer
  4: [ 0- 0]: hardware dependent
  7: [ 0- 3]: hardware dependent
 16: [ 0- 0]: digital audio playback
 17: [ 0- 1]: digital audio playback
 19: [ 0- 3]: digital audio playback
 24: [ 0- 0]: digital audio capture
 25: [ 0- 1]: digital audio capture
 26: [ 0- 2]: digital audio capture
 33:        : timer

Installation issues / Re: Black screen after installation is finished
« on: June 08, 2010, 04:45:09 am »
Check your xorg.conf and make sure "nvidia" is named under the "device" section. It might say "vesa" and this may cause it not to load.

Users / WD1TB Drive
« on: May 09, 2009, 12:25:29 am »
I have a Wester Digital 1 TB Ethernet connected drive on my network. When I plug it into the network I can get an IP from my Cisco Router and/or my Cisco 3560G switch. But when I try to put it on the same network as my LinuxMCE, it receives an IP, but you can't ping it. Linuxmce DHCP shows it handing out a lease to the proper MAC, but it's the "actual" mac. I noticed, Cisco puts a 01 at the beginning and it works fine.

Any reason my WD1TB does not Linuxmce as it's dhcp server?

Pages: [1]