Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - blue_chip

Pages: [1]
1
Installation issues / Re: Black screen after installation is finished
« on: March 02, 2009, 12:23:30 pm »
I'm not entirely sure why your tuner card isn't working...but I can say the red LED is actually if the tuner is active. It's only on when it's being used.

Can you give me the output of lsusb ?

-Thom


I hope it's the correct one...

Code: [Select]
Bus 002 Device 005: ID 2040:2900 Hauppauge
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x2040 Hauppauge
  idProduct          0x2900
  bcdDevice            4.00
  iManufacturer           1
  iProduct                2
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           60
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xc0
      Self Powered
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           6
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass    255 Vendor Specific Subclass
      bInterfaceProtocol    255 Vendor Specific Protocol
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x84  EP 4 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x88  EP 8 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x86  EP 6 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
can't get device qualifier: Operation not permitted
can't get debug descriptor: Operation not permitted
cannot read device status, Operation not permitted (1)

Bus 002 Device 001: ID 0000:0000
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         1 Single TT
  bMaxPacketSize0        64
  idVendor           0x0000
  idProduct          0x0000
  bcdDevice            2.06
  iManufacturer           3
  iProduct                2
  iSerial                 1
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
can't get hub descriptor: Operation not permitted
can't get device qualifier: Operation not permitted
can't get debug descriptor: Operation not permitted
cannot read device status, Operation not permitted (1)

Bus 001 Device 008: ID 05ac:0205 Apple Computer, Inc. Apple Extended Keyboard [Mitsumi]
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x05ac Apple Computer, Inc.
  idProduct          0x0205 Apple Extended Keyboard [Mitsumi]
  bcdDevice            1.22
  iManufacturer           1
  iProduct                3
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           59
    bNumInterfaces          2
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower               50mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Devices
      bInterfaceSubClass      1 Boot Interface Subclass
      bInterfaceProtocol      1 Keyboard
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.10
          bCountryCode           13 International (ISO)
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      65
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              10
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Devices
      bInterfaceSubClass      0 No Subclass
      bInterfaceProtocol      0 None
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.10
          bCountryCode           13 International (ISO)
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength     110
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval             255
cannot read device status, Operation not permitted (1)

Bus 001 Device 007: ID 046d:c51a Logitech, Inc.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x046d Logitech, Inc.
  idProduct          0xc51a
  bcdDevice           41.00
  iManufacturer           1
  iProduct                2
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           59
    bNumInterfaces          2
    bConfigurationValue     1
    iConfiguration          4
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower               98mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Devices
      bInterfaceSubClass      1 Boot Interface Subclass
      bInterfaceProtocol      2 Mouse
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.11
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      67
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval               1
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Devices
      bInterfaceSubClass      0 No Subclass
      bInterfaceProtocol      0 None
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.11
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      79
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval               1
can't get device qualifier: Operation not permitted
can't get debug descriptor: Operation not permitted
cannot read device status, Operation not permitted (1)

Bus 001 Device 006: ID 05ac:1002 Apple Computer, Inc. Apple Extended Keyboard Hub [Mitsumi]
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed hub
  bMaxPacketSize0         8
  idVendor           0x05ac Apple Computer, Inc.
  idProduct          0x1002 Apple Extended Keyboard Hub [Mitsumi]
  bcdDevice            1.22
  iManufacturer           1
  iProduct                2
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower               50mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0001  1x 1 bytes
        bInterval             255
can't get hub descriptor: Operation not permitted
cannot read device status, Operation not permitted (1)

Bus 001 Device 001: ID 0000:0000
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed hub
  bMaxPacketSize0        64
  idVendor           0x0000
  idProduct          0x0000
  bcdDevice            2.06
  iManufacturer           3
  iProduct                2
  iSerial                 1
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
can't get hub descriptor: Operation not permitted
cannot read device status, Operation not permitted (1)


2
Installation issues / Re: Black screen after installation is finished
« on: March 02, 2009, 08:01:49 am »
just plug the USB2 in, LMCE should find it because we have a device template for it.

after I plug the USB In, the Red (Power)Light turn of and LMCE doesn't find anything, when I plug in the USB first and give the device after that power, the Powerlight doesn't come at anytime... I'm guessing it has something to do with the driver, because I had the same problem on windows before I installed the driver...!


As for installing the nvidia drivers, you had to do this BECAUSE you're using a card not certified to work with the driver in 0710. You will not need to do this for 0810, because your card will work with the packaged driver.

Use recommended hardware, and the problems you are having will not happen.

-Thom

dammed I'm SO SORRY! You're right... I guess I was so surprised that everything of my hardware fitted, I forgot to check about the card... (I bought the hardware about a 1 1/2 y ago...)

Thanks for all help here, it's a really great forum...!

Greez


3
Installation issues / Re: Black screen after installation is finished
« on: March 01, 2009, 05:16:58 pm »
http://wiki.linuxmce.org/index.php/Display_Drivers

hey thanks a lot for your tips, were getting closer... :)

After I installed the NVIDIA Driver (in Kubuntu GUI, nvidia-glx-new) I installed LinuxMCE and I can see the AV Wizard... I couldn't install it like on the tutorial - it all ended up with an "http://forum.linuxmce.org/index.php?topic=5503.0"failed to setup x"

But I have still some strange Errors...

I wanted to use 1080p, but the Ratio still standing on 4:3 and i think it;s still 640x480 probably 800x600

When I wanna launch MCE it's coming following error meassege:
Warning: you are using the nv driver. It is recommended that you use the nvidia driver. Do you want to run helper script to try to fix it (this can cause system to reboot?
Press Cancel if you want to close LMCE Launch Manager without running helper script.

When it's finally downloaded LMCE is starting and the error "Open GL isn't available" that only appears when I wanna launch MCE with U2 (without alphablending). But I can start it with U1... But with a Nvidia 8800 u2 should work, shouldn't it?

My actuall xorg log...
http://howflow.com/pastes/1198

Last but not least, when I wanna install my Win-TV-PVR-USB2 according to this tutorial: http://wiki.linuxmce.org/index.php/Hauppauge_WinTV-PVR-USB2
I'm getting following error:
Code: [Select]
ERROR:Module ivtv does not exist in /proc/modules after I typed in
Code: [Select]
sudo rmmod ivtv
unfortunatley MCE doesn't find the card... :(

But I have to say I tried to install the driver in the usual Terminal, because when I hold Alt-Ctrl-2, nothing happen. If I try it with ALT-Ctrl-F2, I'm getting the same error like in the terminal...

Still any suggestions? And thank you for your patience...

Greez

P.S. should I open a new thread for my new problems?


4
Installation issues / Re: Black screen after installation is finished
« on: February 27, 2009, 11:55:36 am »
Do you have an onboard (on motherboard) graphics chip as well as a graphics card?

no...

some more information, what I have tried till now:

first I wanted to install MCE 7.10 with the DVD - it didnt worked. after the step "guessing about my BIOS" (something like that) it stopped even though the installer said it had founded it.

so i tried it with kubuntu 7.10 cd and the 2 MCE Discs with that it worked so far to the black screen. what i'm wondering, even though I have a Nvidia Card the installer of MCE didn't ask me about which UI I wanna use...

I also tried the second DVI-Port at the graphic card- same problem

I'm actually trying to reinstall kubuntu (CD) and then another MCE-Installation - I'm still hopeing it's gonna working....

or has anybody else a suggestion for me?

Greez

5
Installation issues / Re: Black screen after installation is finished
« on: February 26, 2009, 06:53:46 pm »
Hi there

I have also the problem with the black screen after the installation...

First of all my System has the following specs:

Mainb: Asus P5N32-E Sli
Graca: Asus Nvidia GTX 8800
Screen: Viewsonic VP2650wb connected by DVI

After the first Beep I can see a black screen with a blinking cursor flashing, after the second beep the screen turn into standby. I already tried the tricks with the numbers, pressing shift during start up - nothing has worked so far.

After several new starts it shows me from time to time (yes it's really randomly!):
Code: [Select]
Starting Samba [OK]
Restarting UPNP Meda Server fuppesd [OK]
  somtimes also just
Code: [Select]
Restarting UPNP Meda Server fuppesd _
between the two beeps after that the screen is going back into standby...

Does anybody have any suggestions?

Greez

P.S. please excuse me for my bad english... I hope you understand it :)

Pages: [1]