Messages

Hi,

I need some help for next issue: when I tried to turn ON/OFF change the intensity of the light dimmer (quibino) or for any other Z-wave scenario  I got a delay (1-2 minutes) before I will get the result. I don't know from where I should begin the troubleshooting ..If you can help me I will appreciate.

Maybe is useful the following part of log file (DCErouter.log):


sage Changed, retry none, parameters: <0x7fdc0bfff700>
07      02/13/16 23:58:40.026             Parameter 69(Watts): 8 <0x7fdc0bfff700>
08      02/13/16 23:58:40.599           Received Message from 0 (unknown / ) to 47 (Lustra Living / Living Room/Family Room), type 1 id 193 Command:Off, retry none, parameters: <0x7fdb737a6700>
05      02/13/16 23:58:40.649           Socket::ReceiveData 0x7fdc1409a700 failed, bytes left 0 start: 1332363 1: 0 1b: 0 2: 0 2b: 0 m_Socket: 158 Incoming_Conn Socket 158 ::ffff:127.0.0.1 <0x7fdb737a6700>
05      02/13/16 23:58:40.649           Socket::ReceiveString2 ReceiveData failed m_Socket: -1 Incoming_Conn Socket 158 ::ffff:127.0.0.1 <0x7fdb737a6700>
05      02/13/16 23:58:40.649           TCPIP: Closing connection to -1003 (Router Dev #0) 0x7fdc1409a700 m_Socket: -1 <0x7fdb737a6700>
05      02/13/16 23:58:40.649           Router::RemoveAndDeleteSocket 0x7fdc1409a700 -1003 <0x7fdb737a6700>
07      02/13/16 23:58:41.161           Event #85 has no handlers <0x7fdc0bfff700>
07      02/13/16 23:58:41.161           Received Message from 47 (Lustra Living / Living Room/Family Room) to -1001 (unknown / ), type 2 id 85 Event:Power Usage Changed, retry none, parameters: <0x7fdc0bfff700>
07      02/13/16 23:58:41.161             Parameter 69(Watts): 19 <0x7fdc0bfff700>
08      02/13/16 23:58:43.937           Received Message from 0 (unknown / ) to 47 (Lustra Living / Living Room/Family Room), type 1 id 192 Command:On, retry none, parameters: <0x7fdb737a6700>
05      02/13/16 23:58:43.986           Socket::ReceiveData 0x7fdc1409a700 failed, bytes left 0 start: 1338883 1: 0 1b: 0 2: 0 2b: 0 m_Socket: 158 Incoming_Conn Socket 158 ::ffff:127.0.0.1 <0x7fdb737a6700>
05      02/13/16 23:58:43.986           Socket::ReceiveString2 ReceiveData failed m_Socket: -1 Incoming_Conn Socket 158 ::ffff:127.0.0.1 <0x7fdb737a6700>
05      02/13/16 23:58:43.986           TCPIP: Closing connection to -1003 (Router Dev #0) 0x7fdc1409a700 m_Socket: -1 <0x7fdb737a6700>
05      02/13/16 23:58:43.986           Router::RemoveAndDeleteSocket 0x7fdc1409a700 -1003 <0x7fdb737a6700>
07      02/13/16 23:59:20.895           Event #85 has no handlers <0x7fdc0bfff700>
07      02/13/16 23:59:20.895           Received Message from 47 (Lustra Living / Living Room/Family Room) to -1001 (unknown / ), type 2 id 85 Event:Power Usage Changed, retry none, parameters: <0x7fdc0bfff700>

Hello,

      Please let me know if is any solution (workaround/patch, other snapshot)  for using the firewall of LinuxMCE (from lmce-admin). I'm not able to add any rule (inputs/ outputs/port forward) after I installed the snapshot of Kubuntu 14.04 (LMCE-1404-20160101124031783-i386.iso). I'm trying to open port 22 for SSH connection and also port 2757 & 3450 for Android qOrbiter.

Thank you in advance..

Hello,

Does anybody know how if is possible to control an underfloor heating by using a z- wave  network. Is about a house with 3 bedrooms, 2 bathrooms and one livingroom (aprox. 100 sqm) . I was thinking to use as temperature sensor (DS18B20 ) for each room, Z-Wave Universal Binary Sensor to "send" the inputs of the temp. sensors to the controller (Core-Linux MCE). On the controller will give the signal on/off to an electro-valves (using Danfoss Living Connect).
    Please let me know if this is a good solution or if you know one better...

Thank you in advance .

Thank you posde, for your prompt answer.

Do you have any proposal for this issue ?

Hello,

Does anybody know how if is possible to control an underfloor heating by using a z- wave  network. Is about a house with 3 bedrooms, 2 bathrooms and one livingroom (aprox. 100 sqm) . I was thinking to use as temperature sensor (DS18B20 ) for each room, Z-Wave Universal Binary Sensor to "send" the inputs of the temp. sensors to the controller (Core-Linux MCE). On the controller will give the signal on/off to an electro-valves (using Danfoss Living Connect).
    Please let me know if this is a good solution or if you know one better...
Thank you in advance .