Messages

I did that, but when i change to look at the list by file name it dont show me anything
if i look at by any other attrib it works fine
I have different types of music in diferent folders and without filename its all mixed up right now

When I installed Linuxmce I clicked on a hard drive and made it private,  I dont want to be private. The question is can i delete it in the admin site and will I have another chance to configure it? It is loaded with my media and I dont want to loose it.

I thank you for the good info.

on the MD, execute

Code Select Expand


apt-get install alsa-modules-`uname -r`


I already started the upgrade before you replyed, but I would like to know what is the better way. yours looks easier and will it upgrade alsa? and I want to thank you for the reply

I was able to get sound and video using an alsa upgrade script 1.0.24.2 from http://ubuntuforums.org/attachment.php?attachmentid=182961&d=1297117212 (You have to have a user account)

1. download the script and save it somewhere
2. cd <your-download-dir>
3. tar xzvf AlsaUpgrade-1.0.24-2.tar.gz
4. chmod +x AlsaUpgrade-1.0.24-2.sh
5. sudo ./AlsaUpgrade-1.0.24-2.sh -d
6. sudo ./AlsaUpgrade-1.0.24-2.sh -c
7. sudo ./AlsaUpgrade-1.0.24-2.sh -i
8. sudo shutdown -r 0

and when I restarted I hed sound and video!!!

I want to add...

I think it is alsamixer version 1.0.18 on the md that is the problem, I also checked the version on the core and its version 1.0.23
how can I upgrade alsa on the md?

Hello all,

I have an Acer Revo r3610 running as a diskless md with the 330 ion hardware and atheros wifi. I had an issue with the wifi and that is resolved. When I get it to the av wizard I have no sound over hdmi and no video feed for Sarah. I get the UI 2 with flicker and I can navigate just like normal. When I try to play any media I get a blank screen for a sec or 2 then it goes back to flicker with the mute and play/pause buttons. I have the 195 nvidia driver by default installed. I have went to alsamixer and made sure that all is unmuted...no go. I am running snapshot LinuxMCE-8.10-24431-i386.iso.

I have spent hours of research, searching the forums and google any help would be appreciated.

ok I went into /tftpboot/pxelinux.cfg and edited the default boot script to remove acpi=off

now I will try to do another pxe booy on the revo

Ok. I pxe booted the revo and it seems to have stopped at:

* mounting local filesystem...
mount: sysfs already mounted or /sys busy
mount: according to mtab, none is already mounted on /sys               [fail]

* Activating swapfile swap...

I'm going to try to disable acpi to see what will happens

now I have the diskless folder in pluto so I went in:

/usr/pluto/diskless/32/etc/modprobe.d/blacklist

and blacklist ath_pci

then rebooted the core, now i will try again to pxe boot the revo

ok... I got a little ferther this time pxe went all the way through and anounced to the router then rebooted
started again and stopped at:

ip-config: eth0 hardware address 90:fb:a6:2e:29:0a mtu 1500 DHCP RARP
ip-config: no response after 60 secs - giving up
/init: .: line 1: cant open /tmp/net-eth0.config
[  573.059455] Kernel panic - not syncing: attempting to kill init!

any ideas anyone?

"If you have the wifi adapter version of the revo you will need to add 'blacklist ath_pci' to the moons blacklist file. Be sure to modify according to your setup: /usr/pluto/diskless/##/etc/modprobe.d/blacklist"

I do not have the wifi card in my revo, I took it out.
the reason I took it out is because I could not find /usr/pluto/diskless/##/etc/modprobe.d/blacklist to blacklist ath_pci
the folder (diskless) is not in the (pluto) folder on the core and my revo has not been assigned a moon number yet by the core

I tried to use http://wiki.linuxmce.org/index.php/Unrecognized_NIC wiki... I found the kernel module (forcedeth) for nVidia MCP79 ethernet, but I'm not sure if that is the right one. I also found (e1000e) for intel 10/100/100 ethernet, not sure wich one to use or both.
for now I used (forcedeth) when I went to /etc/initramfs-tools-interactor/modules and put in forcedeth in the modules file
then I went to the terminal and put in:

                             sudo /usr/pluto/bin/Diskless_buildDefaultImage.sh ... didn't seem like anything happend
so I Put in:               mkinitramfs -d /etc/initramfs-tools-interactor/ -o /tftpboot/default/initrd...still seem nothing happens

the directions say they are for lmce704, are they also for 810?

hallo all.

I'm tring to install my revo 3610 as a md in my master bedroom.

My core is a dell 4600 with intel 4 2.4Mhz single core processor, 1.5g ram, duel nic (1 onboard and a pci 3com), and a gforce 6200 agp
I used the dvd install of linuxmce 810, I followed the directions to the t from the linuxmce wiki. I have eth0 as external and eth1 as internal networks

When I pxe boot the revo, it starts going through all the motions and stops at could not open /usr/tmp-eth0 or something like that
I removed the internal wifi card out of the revo...no change
I have been researching and found people saying to edit the kernal module at usr/pluto/diskless with the proper driver. I dont have that folder
I have also read that i can blacklist the nic
or update the diskless image with the driver for the nic
I need direction on what I need to do...PLEASE I dont know what to do next