Messages

1

Installation issues / Re: 0810 - MD HDD Install?

« on: October 31, 2009, 11:03:52 pm »

It's a Zotac Ion MiniITX Board with only one Nic (Atom330).

But at the moment i'm installing the core again. Maybe i did some failures in the first install, i'm not sure.
I hope i will get a running MCE system soon. But if yes i see the next problems coming with the touchscreen of the MD....

2

Installation issues / Re: 0810 - MD HDD Install?

« on: October 29, 2009, 10:44:19 am »

Nobody who can help me?

3

Installation issues / Re: 0810 - MD HDD Install?

« on: October 28, 2009, 09:51:20 am »

Ok it stopped, today in the morning it was at the same status.
After rebooting the system it tried to start the config.sh and dhcp.sh but immediately after that the system reboots and make a loop.
config.sh, dhcp.sh, rebooting all the time.

4

Installation issues / Re: 0810 - MD HDD Install?

« on: October 27, 2009, 11:06:09 pm »

Today the new ION MB was delivered. Now i'm just testing the Netboot over cable. But how long does it take to boot to the Wizard the first time?

The last message from the MD client is:
[6.643145] usbhid: v2.6:USB HID core driver

and now it seems to be stopped...

And i'm also not sure that everything is correct. In the admin page i see no MD. But it install a top level device marked as "the core"  with device template "the core #28". I'm really confused.
The template #28 is configured as a core device....

5

Installation issues / Re: 0810 - MD HDD Install?

« on: October 26, 2009, 02:27:26 pm »

Hmm that's not a really good solution, the work is so much and the effort too less. I think if i try this then it's better to make a lot of holes into every wall and use a cable.
But i would like to avoid it, just to install the MD client to a hard disk and install the wifi drivers.

6

Installation issues / 0810 - MD HDD Install?

« on: October 26, 2009, 10:00:52 am »

I have following issue.
Since the weekend my 0810 core server is working well. Now i tried to start installing my first MD, but i noticed that only netboot is supported for a MD only device. But i would like to use a local clean MD install. The first MD is a small kitchen Zotac ION ATOM PC with a kitchen cabinet touchscreen and only with the possibility of wifi connection. wifi and netboot does not work. Also i need to install the tochscreen drivers.
How can i install the MD client like in 0710? Or can i use the 0810 core with a 0710 MD?

I'm sorry for my "noob" questions in advance but it's my first experience with LinuxMCE and i'm also not very firmly with linux in general.

Thanks for your help

Edit: One question more, why i can't install only a dedicated core? My core PC does not need the full installation but 0810 does not have any option to choose CORE/MD/Hybrid. Just one way installation is given. I think it was a good solution in 0710 to choose the install routine.

7

Installation issues / Re: "Failed to setup X" when rebooting after clean installation

« on: October 11, 2009, 04:23:35 pm »

I already bought some 6200 at ebay but this card was defective. So i tried it with a old card that i had on stock.
I will try it again if i have no sucess i will buy another 6200 with hopfully more luck.

8

Installation issues / Re: "Failed to setup X" when rebooting after clean installation

« on: October 11, 2009, 03:54:07 pm »

Thanks for your quick reply's.

No i'm using Kubuntu 7.10 as descripted within the documentation.
I'm using rivaTNT GPU, it's just a core server i need no bigger graphiccard.

Happy Thanksgiving to you, i'm from germany there is no thanksgiving

Edit: OK first i will try Alpha 8.10 if any problem occure with that version i will post again.

9

Installation issues / Re: "Failed to setup X" when rebooting after clean installation

« on: October 11, 2009, 02:50:49 pm »

Hi,

i have the same Problem with the message "Failed to Setup X" but i can't find any thread about this failure.

Thanks for your help.