Messages

Hi.

I need some help with buying an usb wifi stick that works with linuxmce.

I would like to by and plug and play device that works out of the box.


/Jesper

It sounds like really metallic. Like the speakers are in a bootle....   Hm a little big spacy....

Hm and i dont know why i have to choose another audio interface to get the sound.

And the only way i can get sound on is to choose another audio path in the tv card setup.

I use standard setting when I setup the digital tuner.

But need to change to get sound on the analog tuner.....

Ok when i start the backend server i found the analog channels, but the sound are not good... The sound on the digital channels are really good.

Any good ideas

Hi.

After starting the modprobe cx88-dvb i am now able to scan for Digital channels.
And it looks good. and good sound.

Then i tryied to ad my analog recorder, but it dont find anything when i scan.

Do anyone have some help?

I still have the Pci fail as i discribed earlier. Hope someone can give me some helt with this.

Thanks

/Tigerdyr007

I tryed yesteday to start the dvb and it seems to work. after starting it i could see the folder /dev/dvb/adapter0.... But when i go to mce click tv it starts mythtv and now i cant get into the same config window as i did before. So i cant tune channels....

Everytime i start my lmce i get this error, maybe i has something to do with the problem.

[    0.413106] PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:01:00.0


I read that it dont start automatically everytime i start lmce before i send it to /etc.

Maybe i restarted my mce because i also installed my nvidia 7300gt card and there for it stopped the server again, i forgot to check.

Under mythtv i choose utillities/Setup --> and before i could setup the tuner here is that correct.


Answer for your last reply NOS : Am only using Analog signal.


/tigerdyr007


dmes log
[    0.349694] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.349707] pnp: PnP ACPI init
[    0.394457] pnp: PnP ACPI: found 15 devices
[    0.394462] PnPBIOS: Disabled by ACPI PNP
[    0.394514] PCI: Using ACPI for IRQ routing
[    0.394517] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[    0.394523] PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.1
[    0.394525] PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.1
[    0.394528] PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.1
[    0.410634] NET: Registered protocol family 8
[    0.410637] NET: Registered protocol family 20
[    0.413106] PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:01:00.0
[    0.413148] PCI: Bridge: 0000:00:01.0
[    0.413151]   IO window: 4000-4fff
[    0.413156]   MEM window: d0000000-d1ffffff
[    0.413160]   PREFETCH window: c0000000-cfffffff
[    0.413164] PCI: Bridge: 0000:00:1c.0
[    0.413167]   IO window: 5000-5fff
[    0.413172]   MEM window: d5000000-d50fffff
[    0.413176]   PREFETCH window: disabled.
[    0.413181] PCI: Bridge: 0000:00:1c.1
[    0.413182]   IO window: disabled.
[    0.413187]   MEM window: disabled.
[    0.413191]   PREFETCH window: disabled.
[    0.413196] PCI: Bridge: 0000:00:1e.0
[    0.413197]   IO window: disabled.
[    0.413202]   MEM window: d2000000-d4ffffff
[    0.413206]   PREFETCH window: disabled.
[    0.413224] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16

Thanks that works.

Super i try that when i come home...

How can i see that the frontend is running?


And when i after trying you command go to mythtv to set the card up, is there some special things i have to select. I need to scan for Analog channels.

Thanks for your help....

/Tigerdyr007

Hi.

When i set my graphics to openGL alpha blending i get an error.

A black box telling Obieter failed to setup the tranperency.....

Any one know what to do to fix it?

/Tigerdyr007

Hi Nos

Thanks for the fast answer.

i have looked in the dmesg log and it seems to be listed.

I have pasted it into the botton of this mail.

I could not find the /dev/dvb folder. so maybe it not correct started.

I went in to the kde info clicked on pci and here is some info

0a:0c.0 Multimedia video controller: Conexant cx23880/1/2/3 PCI Video and Audio Decoder (rev 05)

Subsystem: Hauppauge computer works Inc. Unknown device 9600
flags: bus master, medium devsel latency 165, IRQ 21
Memory at d20000000 (32-bit, non prefetchable) [size 16m]
capabilities: <access denied>

i have to more like this one. One for Audio, and one for Mpeg port

Hope you can figure out whats wrong


dmesg

0.535380] PCI: Using ACPI for IRQ routing
[    0.535384] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[    0.535389] PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.1
[    0.535391] PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.1
[    0.535393] PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.1
[    0.551576] NET: Registered protocol family 8
[    0.551579] NET: Registered protocol family 20
[    0.554094] PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:01:00.0
[    0.554135] PCI: Bridge: 0000:00:01.0
[    0.554138]   IO window: 4000-4fff
[    0.554143]   MEM window: d0000000-d1ffffff
[    0.554147]   PREFETCH window: c0000000-cfffffff
[   14.049683] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   14.466722] NET: Registered protocol family 17
[   14.478461] Linux agpgart interface v0.102 (c) Dave Jones
[   14.483460] agpgart: Detected an Intel 945G Chipset.
[   14.500365] agpgart: AGP aperture is 256M @ 0x0
[   14.641140] input: PC Speaker as /class/input/input2
[   14.780898] intel_rng: FWH not detected
[   14.847423] Linux video capture interface: v2.00
[   14.995024] cx2388x v4l2 driver version 0.0.6 loaded
[   14.995099] ACPI: PCI Interrupt 0000:0a:0c.0[A] -> GSI 20 (level, low) -> IRQ 21
[   14.995161] CORE cx88[0]: subsystem: 0070:9600, board: Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encoder [card=56,autodetected]
[   14.995166] TV tuner 63 at 0x1fe, Radio tuner -1 at 0x1fe
[   15.009967] cx2388x cx88-mpeg Driver Manager version 0.0.6 loaded
[   15.025039] iTCO_vendor_support: vendor-support=0
[   15.026632] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
[   15.047324] parport: PnPBIOS parport detected.
[   15.047412] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[   15.166875] tveeprom 0-0050: Hauppauge model 96559, rev C5A0, serial# 1221779
[   15.166882] tveeprom 0-0050: MAC address is 00-0D-FE-12-A4-93
[   15.166887] tveeprom 0-0050: tuner model is Philips FMD1216ME (idx 100, type 63)
[   15.166892] tveeprom 0-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4)
[   15.166897] tveeprom 0-0050: audio processor is CX882 (idx 33)
[   15.166900] tveeprom 0-0050: decoder processor is CX882 (idx 25)
[   15.166904] tveeprom 0-0050: has radio, has no IR receiver, has no IR transmitter
[   15.166908] cx88[0]: hauppauge eeprom: model=96559
[   15.167024] input: cx88 IR (Hauppauge WinTV-HVR130 as /class/input/input3
[   15.167077] cx88[0]/0: found at 0000:0a:0c.0, rev: 5, irq: 21, latency: 165, mmio: 0xd2000000
[   15.222983] tuner 0-0061: chip found @ 0xc2 (cx88[0])
[   15.225953] tuner 0-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner)
[   15.229101] tuner 0-0061: type set to 63 (Philips FMD1216ME MK3 Hybrid Tuner)
[   15.230286] tuner 0-0063: chip found @ 0xc6 (cx88[0])
[   15.253160] cx2388x alsa driver version 0.0.6 loaded
[   15.267686] wm8775 0-001b: chip found @ 0x36 (cx88[0])
[   15.276189] cx88[0]/0: registered device video0 [v4l2]
[   15.276242] cx88[0]/0: registered device vbi0
[   15.276290] cx88[0]/0: registered device radio0
[   15.288505] cx88[0]/2: cx2388x 8802 Driver Manager
[   15.288538] ACPI: PCI Interrupt 0000:0a:0c.2[A] -> GSI 20 (level, low) -> IRQ 21
[   15.288555] cx88[0]/2: found at 0000:0a:0c.2, rev: 5, irq: 21, latency: 49, mmio: 0xd4000000
[   15.288607] ACPI: PCI Interrupt 0000:0a:0c.1[A] -> GSI 20 (level, low) -> IRQ 21
[   15.288643] cx88[0]/1: CX88x/0: ALSA support for cx2388x boards
[   15.398409] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[   15.398430] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   15.484990] input: ImExPS/2 Logitech Wheel Mouse as /class/input/input4
[   15.488115] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x1060)
[   15.488161] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   15.748808] fuse init (API version 7.
[   15.757854] lp0: using parport0 (interrupt-driven).
[   15.802395] Netfilter messages via NETLINK v0.30.
[   15.811709] nf_conntrack version 0.5.0 (4073 buckets, 32584 max)
[   16.154440] Adding 1951952k swap on /dev/sda5.  Priority:-1 extents:1 across:1951952k
[   16.266818] EXT3 FS on sda1, internal journal

Im complet new linux user. I say the video about linuxmce, which look really good. I want to convert my windows media center to a linuxmce. The installation went out fine. But i cant get my tv/tuner to work. In the Preface to the video documentention it says aften inserting the tvtuner in the pc it will recognize the card automatic, but nothing happend when i start my computer up and when i try to find it under Provder nothing is displayed.

Can anyone help me to get it to work?

Is it a driver i need?

Hope someone can help me.

Dont hope i have to buy a new Tvtuner to make it work.

Thank for your help.

Tigerdyr007