Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - nightcanton

Pages: [1]
1
Users / Re: WAYNE-DALTON Z-WAVE® THERMOSTAT
« on: May 01, 2011, 11:16:40 pm »
So I got it connected.  Both the Zwave mcv dongle and the thermostat are installed and paired. (The Zwave symbol on the wayne dalton themostat is blinking.)

Now I'm trying to change the scenarios but no matter what I don't see a change in the thermostat itself.  Thoughts on the picture?

2
Users / Re: WAYNE-DALTON Z-WAVE® THERMOSTAT
« on: March 20, 2011, 12:23:08 am »
So are you saying based on the screen shots the MCV dongle looks to be installed?

If so, then my next question is to actually connect the thermostat and configure it.

3
Users / Re: WAYNE-DALTON Z-WAVE® THERMOSTAT
« on: March 06, 2011, 10:42:42 pm »
I followed the steps in the wiki.  But I can't seem to even figure out if it is installed correctly.   Even when I go to the admin page I don't really see any way to setup the thermostat.

I took 2 screenshots and can take more if needed.  I would greatly appreciate the help.

4
Users / Re: WAYNE-DALTON Z-WAVE® THERMOSTAT
« on: February 12, 2011, 04:01:57 pm »
so is there a good how to to do this?  i've followed everything on this post, the mcv dongle wiki, and the wayne dalton thermostat intsall page but csant get it working.  thoughts?

5
Users / Re: WAYNE-DALTON Z-WAVE® THERMOSTAT
« on: February 06, 2011, 08:53:42 pm »
I just bought one of these wd thermostats and have the MCV usb dongle.

I plug the MCV dongle into the server and it loads up the 'lighting wizard'.

I've tried to setup a climate device/scenario but can't get this to work.

Any thoughts?

6
Installation issues / Re: 810 installation hangs when detecting file systems at 15%
« on: April 07, 2010, 01:18:28 am »
Never figured it out but just installed 7.10 and it is working great.

7
Installation issues / Re: 810 installation hangs when detecting file systems at 15%
« on: March 28, 2010, 06:15:09 pm »
Did this ever get solved?  I'm having the same problem.  

My install is hanging on formatting the main partition of my drive.  I have tried 3 different hard drives (2 sata and 1 IDE), different burned DVD, Tested all hardware with 2 different all inclusive utilities and STILL can't get past the partition formatting piece.

I even tried doing the install via booting into the LiveCD and formated the partitions that the previous install created hoping that it would just skip the formatting.  Thoughts?

8
Users / Re: Can't see Jpegs
« on: April 29, 2007, 06:43:35 pm »
Here is a link I found.

Not sure if it is still valid after a month.

It says that the picture viewing isn't avalable yet.  This was as of April 4th.

http://forum.linuxmce.com/index.php?topic=1405.0

Can anyone answer this?

9
Users / Re: Can't see Jpegs
« on: April 28, 2007, 11:04:03 pm »
I even tried logging in as root and I still can't see images inside the LINUXMCE gui in the "media > Pictures" area.

10
Users / Can't see Jpegs
« on: April 28, 2007, 09:59:34 pm »
I copied a couple of Jpegs into the "/home/public/data/pictures" folder.  When using the menu it doesn't show previews and when I open the file it just shows up blue.

Changed the permissions of the "/home/plublic" folders and files to 777.

Any Ideas?

11
Installation issues / Installed Ubuntu and LinuxMCE but have black screen with errors in log No GUI
« on: April 28, 2007, 04:34:50 pm »
I have tried several times to get this squared up.  I tried installing onto several different systems with different configs.  All have problems of some sorts.

So I'm trying to get this working in VMware to see if this will ever work.   I boot to the Ubuntu gui first.  Then click on LinuxMCE.  It first loaded to a gray screen.  When I changed resolutions it came up with a transparency issue.  I switched the UI2 to UI1 in the Media Director section on the web interface.  Now  I just get a black screen.

I tried loading an orbiter on a windows computer but it says that "Orbiter cannot register with the router."

Here is the log for pluto.

"dcerouter:~$ cat /var/log/pluto/pluto.log
2       04/28/07 08:44:10       17 (spawning-device)    Device requests restart.  .. count=1/50 dev=17
2       04/28/07 08:44:10       27 (spawning-device)    Device requests restart.   .. count=1/50 dev=27
2       04/28/07 08:44:10       60 (spawning-device)    Device requests restart.   .. count=1/50 dev=60
2       04/28/07 08:44:10       15 (spawning-device)    Device requests restart.  .. count=1/50 dev=15
2       04/28/07 08:44:11       21 (spawning-device)    Device requests restart.     .. count=1/50 dev=21
1       04/28/07 08:44:14       DCERouter (server)      Device requests restart. .. count=1/200 dev=DCERouter
1       04/28/07 08:44:14       DCERouter (server)      Starting... 1
1       04/28/07 08:44:18       17 (spawning-device)    Starting... 1
1       04/28/07 08:44:18       17 (spawning-device)    Found ./Text_To_Speech
1       04/28/07 08:44:18       60 (spawning-device)    Starting... 1
1       04/28/07 08:44:18       60 (spawning-device)    Found ./Asterisk
1       04/28/07 08:44:18       27 (spawning-device)    Starting... 1
1       04/28/07 08:44:18       27 (spawning-device)    Found ./External_Media_Identifier
1       04/28/07 08:44:18       15 (spawning-device)    Starting... 1
2       04/28/07 08:44:18       15 (spawning-device)    Reload watcher: running Start_LocalDevices
1       04/28/07 08:44:19       15 (spawning-device)    Found ./App_Server
1       04/28/07 08:44:19       21 (spawning-device)    Starting... 1
1       04/28/07 08:44:19       21 (spawning-device)    Found ./HAL
1       04/28/07 08:44:25       Launching child devices for device: 1 (server)
2       04/28/07 08:44:25       Start_LocalDevices.sh (server)  Start_LocalDevices ; CommandList: 15AppServer0 17TextToSpeech0 18GenericPCasMD0 19OnScreenOrbiterLaunchOrbiter.sh0 21HAL0 27ExternalMediaIdentifier0 60Asterisk0 61Unichrome0
1       04/28/07 08:44:25       Start_LocalDevices.sh (server)  15855 Dev: 15; Already Running list: 27,17,21,19,15,60,
1       04/28/07 08:44:25       Start_LocalDevices.sh (server)  15855 Device 15 was marked as 'running'. Not starting
1       04/28/07 08:44:25       Start_LocalDevices.sh (server)  15855 Dev: 17; Already Running list: 27,17,21,19,15,60,
1       04/28/07 08:44:25       Start_LocalDevices.sh (server)  15855 Device 17 was marked as 'running'. Not starting
1       04/28/07 08:44:25       Start_LocalDevices.sh (server)  15855 Dev: 18; Already Running list: 27,17,21,19,15,60,
2       04/28/07 08:44:25       Start_LocalDevices.sh (server)  Child device (18) was configured but the startup script (Generic_PC_as_MD) is not available in /usr/pluto/bin.
1       04/28/07 08:44:25       Start_LocalDevices.sh (server)  15855 Dev: 19; Already Running list: 27,17,21,19,15,60,
1       04/28/07 08:44:25       Start_LocalDevices.sh (server)  15855 Device 19 was marked as 'running'. Not starting
1       04/28/07 08:44:26       Start_LocalDevices.sh (server)  15855 Dev: 21; Already Running list: 27,17,21,19,15,60,
1       04/28/07 08:44:26       Start_LocalDevices.sh (server)  15855 Device 21 was marked as 'running'. Not starting
1       04/28/07 08:44:26       Start_LocalDevices.sh (server)  15855 Dev: 27; Already Running list: 27,17,21,19,15,60,
1       04/28/07 08:44:26       Start_LocalDevices.sh (server)  15855 Device 27was marked as 'running'. Not starting
1       04/28/07 08:44:26       Start_LocalDevices.sh (server)  15855 Dev: 60; Already Running list: 27,17,21,19,15,60,
1       04/28/07 08:44:26       Start_LocalDevices.sh (server)  15855 Device 60was marked as 'running'. Not starting
1       04/28/07 08:44:26       Start_LocalDevices.sh (server)  15855 Dev: 61; Already Running list: 27,17,21,19,15,60,
2       04/28/07 08:44:26       Start_LocalDevices.sh (server)  Child device (61) was configured but the startup script (Unichrome) is not available in /usr/pluto/bin."


Any Ideas?

Pages: [1]