Hi every one
I'm in the process of get components to start building a system and I was wondering if any one has tried an Asus M2N-SLI Deluxe or if anyone can tell me if there will be any problems in using this mother board.
I have had success with an M2N-E which shares a lot of Silicon. No point in buying one over the recommended board but if you already have it its worth a try.
i was looking at this board due to the dual gigabit and 3 pci slots witch will fill my hardware needs, the spdif will also be good
i was planing on a amd 6000 proc with 2G ram and Nvidia 7050 vga card up to 3 tuners cards
i'm planning on building the core fairly hi spec as i want to roll it out thought my whole house
i was looking at using the hauppauge hvr 1300 as my tuners Has any one had any bad experences with these?
otherwise i was looking at the Nova T 500 cards but i dont think they have the hardware encoders
Any thoughts or suggestions would be appercated
1) figure analog tuners will be landfill after 2009.
2) The core only uses 1 GB of ram. (I know- I have 2G and 1G isn't used. I'm going to pull it the next time I shut it down.)
3) The nVidia 7050 is new and may not be supported with the nvidia-glx driver. Check before you buy.
4) I would get some HDHomeRun tuners, they don't use resources on the core and work real well. And ATSC can have 4 streams on a single channel.
5) The external nic doesn't need to be anything special- your broadband connection rarely is even 10 Mbps. I use the single nic configuration myself.
the only problem is i believe that the HDHomeRun tuners are not available in australia
I have just installed the M2N-deluxe and it works perfectly out of the box!
Haven't tried the s/pdif or coax out though, so not sure if they're supported by the alsa driver.
Anyway, it's a fully recommended board by me!!
Sorry:
I didn't realize you were in a different market. I know SiliconDust is working to get a version for Europe but Australia isn't on the immediate future.
In which case the bigger MB makes sense. However you shouldn't need much more than a 3800 or 4200 processor unless you will be using TVTime software HD Decoding. (Does work better but doesn't work with the overlay/blending.)
Also, I have a NOVA-T 500 tuner, it works perfectly well (follow the instructions here to install it : http://www.mythtv.org/wiki/index.php/Hauppauge_WinTV_Nova-T_500_PCI)
Also, you are right, it doesn't have a hardware decoder, no dvb-t tuners have as they're not required!
dvb-t streams in mpeg-2 format, so it is already 'decoded' and can be burned straight to disc.
Analogue TV does need decoding as it is not in mpeg-2 format. That is why the HVR-1300 has on-board decoding (but I have read that the HVR-1300 decoder is not yet supported in linux anyway)
My advice: get a NOVA-T 500
Quote from: 1audio on September 10, 2007, 05:11:23 PM
Sorry:
I didn't realize you were in a different market. I know SiliconDust is working to get a version for Europe but Australia isn't on the immediate future.
In which case the bigger MB makes sense. However you shouldn't need much more than a 3800 or 4200 processor unless you will be using TVTime software HD Decoding. (Does work better but doesn't work with the overlay/blending.)
DVB-T for Europe is essentially the same as in Australia, so a board for Europe will almost certainly work just fine in Australia as well. I second 1audio's remarks on Analogue TV, don't waste your time! It gets turned off even earlier in Australia - 2008, so its a waste of time and money! If you just want to capture video sources (such as a VHS) then buy a video capture card, don't bother with the turner, same goes if you are trying to capture something like Foxtel.
ok so i'll go with the Nova T 500 for the tuners. So with that sorted, what cards would you use for video input i have and old VHS that i would like to keep and also like to connect the video from my security camera DVR and control it with IR