hallo all.
I'm tring to install my revo 3610 as a md in my master bedroom.
My core is a dell 4600 with intel 4 2.4Mhz single core processor, 1.5g ram, duel nic (1 onboard and a pci 3com), and a gforce 6200 agp
I used the dvd install of linuxmce 810, I followed the directions to the t from the linuxmce wiki. I have eth0 as external and eth1 as internal networks
When I pxe boot the revo, it starts going through all the motions and stops at could not open /usr/tmp-eth0 or something like that
I removed the internal wifi card out of the revo...no change
I have been researching and found people saying to edit the kernal module at usr/pluto/diskless with the proper driver. I dont have that folder
I have also read that i can blacklist the nic
or update the diskless image with the driver for the nic
I need direction on what I need to do...PLEASE I dont know what to do next
Hi,
And Welcome to Linuxmce,
I had a similar problem with a MD, Zotac Ion. I read up and down through the forums about blacklisting the nic driver and other solutions.
I a desperate attempt I deleted the MD from the WebAdmin, rebooted the core and then booted the MD.
Now this was where I messed up the first time...... The MD gets to a point in the boot process where it looks like its doing nothing. Got stuck. I rebooted the MD and got more or less the same problem as you.
But the second time around I just left it...... and about 30min later it was booting to AV-wizard.
The think about LInuxMCE is, you need to have patience.
This is what worked for me.
Karel
Quote from: dspano on September 06, 2010, 05:24:01 AM
hallo all.
I'm tring to install my revo 3610 as a md in my master bedroom.
My core is a dell 4600 with intel 4 2.4Mhz single core processor, 1.5g ram, duel nic (1 onboard and a pci 3com), and a gforce 6200 agp
I used the dvd install of linuxmce 810, I followed the directions to the t from the linuxmce wiki. I have eth0 as external and eth1 as internal networks
When I pxe boot the revo, it starts going through all the motions and stops at could not open /usr/tmp-eth0 or something like that
I removed the internal wifi card out of the revo...no change
I have been researching and found people saying to edit the kernal module at usr/pluto/diskless with the proper driver. I dont have that folder
I have also read that i can blacklist the nic
or update the diskless image with the driver for the nic
I need direction on what I need to do...PLEASE I dont know what to do next
More than likely if its newer hardware use
http://wiki.linuxmce.org/index.php/Unrecognized_NIC
to add your updated driver
HTH
Tim
I have the revo 3610 and I have blacklisted the driver as described in the wiki:
If you have the wifi adapter version of the revo you will need to add 'blacklist ath_pci' to the moons blacklist file. Be sure to modify according to your setup: /usr/pluto/diskless/##/etc/modprobe.d/blacklist
Without this step my md will freeze during the boot process.
Barney
"If you have the wifi adapter version of the revo you will need to add 'blacklist ath_pci' to the moons blacklist file. Be sure to modify according to your setup: /usr/pluto/diskless/##/etc/modprobe.d/blacklist"
I do not have the wifi card in my revo, I took it out.
the reason I took it out is because I could not find /usr/pluto/diskless/##/etc/modprobe.d/blacklist to blacklist ath_pci
the folder (diskless) is not in the (pluto) folder on the core and my revo has not been assigned a moon number yet by the core
I tried to use http://wiki.linuxmce.org/index.php/Unrecognized_NIC wiki... I found the kernel module (forcedeth) for nVidia MCP79 ethernet, but I'm not sure if that is the right one. I also found (e1000e) for intel 10/100/100 ethernet, not sure wich one to use or both.
for now I used (forcedeth) when I went to /etc/initramfs-tools-interactor/modules and put in forcedeth in the modules file
then I went to the terminal and put in:
sudo /usr/pluto/bin/Diskless_buildDefaultImage.sh ... didn't seem like anything happend
so I Put in: mkinitramfs -d /etc/initramfs-tools-interactor/ -o /tftpboot/default/initrd...still seem nothing happens
the directions say they are for lmce704, are they also for 810?
ok... I got a little ferther this time pxe went all the way through and anounced to the router then rebooted
started again and stopped at:
ip-config: eth0 hardware address 90:fb:a6:2e:29:0a mtu 1500 DHCP RARP
ip-config: no response after 60 secs - giving up
/init: .: line 1: cant open /tmp/net-eth0.config
[ 573.059455] Kernel panic - not syncing: attempting to kill init!
any ideas anyone?
now I have the diskless folder in pluto so I went in:
/usr/pluto/diskless/32/etc/modprobe.d/blacklist
and blacklist ath_pci
then rebooted the core, now i will try again to pxe boot the revo
Ok. I pxe booted the revo and it seems to have stopped at:
* mounting local filesystem...
mount: sysfs already mounted or /sys busy
mount: according to mtab, none is already mounted on /sys [fail]
* Activating swapfile swap...
I'm going to try to disable acpi to see what will happens
ok I went into /tftpboot/pxelinux.cfg and edited the default boot script to remove acpi=off
now I will try to do another pxe booy on the revo