General > Users
DVB Cards info needed for Templates
tux-box1:
card http://hauppauge.com/site/products/data_hvr2250.html
--- Quote from: MANDINGO on December 19, 2009, 08:14:02 pm ---
sudo lspci -vn
post your output for your card complete
if usb device then run
sudo lsusb -vn
post your output for your card complete
then run
sudo apt-get install ivtv-utils
install and then run
sudo v4l2-ctl -n
post your ouput for your card complete
also let me know if you had to install and compile drivers for your card and if firmware is needed thanks
you can catch me in the irc channels Linuxmce and Linuxmce-devel
--- End quote ---
--- Code: ------@dcerouter:~$ sudo lspci -vn
00:00.0 0600: 1002:5957
Subsystem: 1043:8353
Flags: bus master, 66MHz, medium devsel, latency 0
Capabilities: [c4] HyperTransport: Slave or Primary Interface
Capabilities: [40] HyperTransport: Retry Mode
Capabilities: [54] HyperTransport: UnitID Clumping
Capabilities: [9c] HyperTransport: #1a
Kernel modules: ati-agp
00:02.0 0604: 1002:5978
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fa000000-fdffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Capabilities: [50] Power Management version 3
Capabilities: [58] Express Root Port (Slot-), MSI 00
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Capabilities: [b0] Subsystem: 1043:8353
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [110] Virtual Channel <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:07.0 0604: 1002:597d
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: fe000000-fe7fffff
Capabilities: [50] Power Management version 3
Capabilities: [58] Express Root Port (Slot-), MSI 00
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Capabilities: [b0] Subsystem: 1043:8353
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [110] Virtual Channel <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:0a.0 0604: 1002:597f
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: 00000000f8f00000-00000000f8ffffff
Capabilities: [50] Power Management version 3
Capabilities: [58] Express Root Port (Slot-), MSI 00
Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Capabilities: [b0] Subsystem: 1043:8353
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [110] Virtual Channel <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:11.0 0106: 1002:4390 (prog-if 01)
Subsystem: 1043:8389
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 22
I/O ports at b000 [size=8]
I/O ports at a000 [size=4]
I/O ports at 9000 [size=8]
I/O ports at 8000 [size=4]
I/O ports at 7000 [size=16]
Memory at f9fffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 2
Capabilities: [70] SATA HBA <?>
Kernel driver in use: ahci
Kernel modules: ahci
00:12.0 0c03: 1002:4397 (prog-if 10)
Subsystem: 1043:8389
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
Memory at f9ffe000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:12.1 0c03: 1002:4398 (prog-if 10)
Subsystem: 1043:8389
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
Memory at f9ffd000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:12.2 0c03: 1002:4396 (prog-if 20)
Subsystem: 1043:8389
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 17
Memory at f9fff800 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:13.0 0c03: 1002:4397 (prog-if 10)
Subsystem: 1043:8389
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 18
Memory at f9ffc000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.1 0c03: 1002:4398 (prog-if 10)
Subsystem: 1043:8389
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 18
Memory at f9ffb000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.2 0c03: 1002:4396 (prog-if 20)
Subsystem: 1043:8389
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 19
Memory at f9fff400 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:14.0 0c05: 1002:4385 (rev 3c)
Subsystem: 1043:8389
Flags: 66MHz, medium devsel
Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: piix4_smbus
Kernel modules: i2c-piix4
00:14.1 0101: 1002:439c (prog-if 8a [Master SecP PriP])
Subsystem: 1043:8389
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
I/O ports at 01f0 [size=8]
I/O ports at 03f4 [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=1]
I/O ports at ff00 [size=16]
Capabilities: [70] Message Signalled Interrupts: Mask- 64bit- Queue=0/1 Enable-
Kernel driver in use: pata_atiixp
Kernel modules: pata_atiixp
00:14.2 0403: 1002:4383
Subsystem: 1043:8417
Flags: bus master, slow devsel, latency 64, IRQ 16
Memory at f9ff4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:14.3 0601: 1002:439d
Subsystem: 1043:8389
Flags: bus master, 66MHz, medium devsel, latency 0
00:14.4 0604: 1002:4384 (prog-if 01)
Flags: bus master, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=04, subordinate=04, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Prefetchable memory behind bridge: f0000000-f00fffff
00:14.5 0c03: 1002:4399 (prog-if 10)
Subsystem: 1043:8389
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 18
Memory at f9ffa000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:18.0 0600: 1022:1200
Flags: fast devsel
Capabilities: [80] HyperTransport: Host or Secondary Interface
00:18.1 0600: 1022:1201
Flags: fast devsel
00:18.2 0600: 1022:1202
Flags: fast devsel
00:18.3 0600: 1022:1203
Flags: fast devsel
Capabilities: [f0] Secure device <?>
00:18.4 0600: 1022:1204
Flags: fast devsel
01:00.0 0300: 10de:0640 (rev a1)
Subsystem: 1043:82fd
Flags: bus master, fast devsel, latency 0, IRQ 18
Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Memory at d0000000 (64-bit, prefetchable) [size=256M]
Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
I/O ports at cc00 [size=128]
[virtual] Expansion ROM at fcf80000 [disabled] [size=512K]
Capabilities: [60] Power Management version 3
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Capabilities: [78] Express Endpoint, MSI 00
Capabilities: [b4] Vendor Specific Information <?>
Capabilities: [100] Virtual Channel <?>
Capabilities: [128] Power Budgeting <?>
Capabilities: [600] Vendor Specific Information <?>
Kernel driver in use: nvidia
Kernel modules: nvidia, nvidiafb
02:00.0 0480: 1131:7164 (rev 81)
Subsystem: 0070:8891
Flags: bus master, fast devsel, latency 0, IRQ 19
Memory at fe400000 (64-bit, non-prefetchable) [size=4M]
Memory at fe000000 (64-bit, non-prefetchable) [size=4M]
Capabilities: [40] Message Signalled Interrupts: Mask- 64bit+ Queue=0/4 Enable-
Capabilities: [50] Express Endpoint, MSI 00
Capabilities: [74] Power Management version 3
Capabilities: [7c] Vendor Specific Information <?>
Capabilities: [100] Vendor Specific Information <?>
Capabilities: [160] Virtual Channel <?>
Kernel driver in use: saa7164
Kernel modules: saa7164
03:00.0 0200: 10ec:8168 (rev 03)
Subsystem: 1043:83a3
Flags: bus master, fast devsel, latency 0, IRQ 220
I/O ports at d800 [size=256]
Memory at f8fff000 (64-bit, prefetchable) [size=4K]
Memory at f8ff8000 (64-bit, prefetchable) [size=16K]
Expansion ROM at feaf0000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Capabilities: [70] Express Endpoint, MSI 01
Capabilities: [ac] MSI-X: Enable- Mask- TabSize=4
Capabilities: [cc] Vital Product Data <?>
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 00-00-00-00-00-00-00-00
Kernel driver in use: r8169
Kernel modules: r8169
04:07.0 0200: 10ec:8169 (rev 10)
Subsystem: 10ec:8169
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 22
I/O ports at e800 [size=256]
Memory at febffc00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at f0000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Kernel driver in use: r8169
Kernel modules: r8169
04:08.0 0c00: 1106:3044 (rev c0) (prog-if 10)
Subsystem: 1043:81fe
Flags: bus master, medium devsel, latency 64, IRQ 23
Memory at febff000 (32-bit, non-prefetchable) [size=2K]
I/O ports at ec00 [size=128]
Capabilities: [50] Power Management version 2
Kernel driver in use: ohci1394
Kernel modules: ohci1394
---@dcerouter:~$ sudo v4l2-ctl -n
Failed to open /dev/video0: No such file or directory
--- End code ---
dirkcolaert:
I use a Hauppauge HVR 1900 (European version). It works on LinuxMCE 8.10 without changes. It has multiple inputs (analogue, digital, ...) but apparently I can only use one because of a bug in MythTV.
I use the analogue input.
this is the listing after interrogating linux about the usb.
--- Code: ---Bus 001 Device 004: ID 2040:7300 Hauppauge
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x2040 Hauppauge
idProduct 0x7300
bcdDevice 8.00
iManufacturer 1 Hauppauge
iProduct 2 WinTV
iSerial 3 7300-00-F06D39E9
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 60
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 6
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x88 EP 8 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0003
Self Powered
Remote Wakeup Enabled
--- End code ---
Esperanto:
DD DuoFlex S2 Octopus - Twin Tuner Card DVB-S/S2 (4 Port Bridge)
http://shop.digital-devices.de/epages/62357162.sf/en_GB/?ObjectPath=/Shops/62357162/Products/091012
sudo lspci -vn
--- Code: ---06:00.0 0480: dd01:0003
Subsystem: dd01:0001
Flags: bus master, fast devsel, latency 0, IRQ 44
Memory at f7100000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 3
Capabilities: [70] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Capabilities: [90] Express Endpoint, MSI 00
Capabilities: [100] Vendor Specific Information <?>
Kernel driver in use: DDBridge
Kernel modules: ddbridge
--- End code ---
sudo v4l2-ctl -n
--- Code: ---Failed to open /dev/video0: No such file or directory
--- End code ---
running the latest drivers from
http://linuxtv.org/hg/~endriss/media_build_experimental
on the 3.0.0 kernel.
joots007:
Hi,
Has anyone got the hauppauge hvr-2210 working. I have tried in Ubuntu with no luck and am looking at other distributions to see if it is any easier.
Thanks in advance.
Alblasco1702:
if you still want data for v card templates min is a Anysee E30 Combo plus.
it is a usb card.
for dvb-t/c and have IR and a smartcard reader on board.
smartcard reader not supported by the current driver
lsusb -v:
Bus 002 Device 004: ID 1c73:861f AMT Anysee E30 USB 2.0 DVB-T Receiver
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1c73 AMT
idProduct 0x861f Anysee E30 USB 2.0 DVB-T Receiver
bcdDevice 1.00
iManufacturer 1 AMT.CO.KR
iProduct 2 anysee-FA(LP)
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 83
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 4
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x1400 3x 1024 bytes
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type None
Usage Type Data
wMaxPacketSize 0x1400 3x 1024 bytes
bInterval 1
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0002
(Bus Powered)
Remote Wakeup Enabled
v4l2-ctl -n
isn't working.
i'm on 1204.
on 1204 i didnt do something to install it,
onlyfor dvb-t need to do:
mv /dev/dvb/adaptor0/frontend0 /dev/dvb/adaptor0/frontend2
mv /dev/dvb/adaptor0/frontend1 /dev/dvb/adaptor0/frontend0
mv /dev/dvb/adaptor0/frontend2 /dev/dvb/adaptor0/frontend1
and restart vdr.
hope this helps you if you need more info you can find me on IRC.
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version