Author Topic: pvr-usb2 not working in 810 alpha 2.29  (Read 492 times)

permo

  • Making baby steps
  • Posts: 3
    • View Profile
pvr-usb2 not working in 810 alpha 2.29
« on: August 18, 2009, 10:54:53 pm »
Hello!

I just upgraded from 7.10 to the latest alpha release, and now I cant get my pvr-usb2 to work. It does not seem to load properly.

Dmesg:

 22.805068] Linux video capture interface: v2.00
[   22.948966] usbcore: registered new interface driver pvrusb2
[   22.949011] pvrusb2: Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner : V4L in-tree version
[   22.949014] pvrusb2: Debug mask is 31 (0x1f)
[   23.146009] cx25840' 0-0044: cx25843-24 found @ 0x88 (pvrusb2_a)
[   23.341202] tuner' 0-0043: chip found @ 0x86 (pvrusb2_a)
[   23.368250] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[   23.368273] Intel ICH 0000:00:1f.5: setting latency timer to 64
[   23.461352] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input5
[   23.496897] tda9887 0-0043: creating new instance
[   23.496901] tda9887 0-0043: tda988[5/6/7] found
[   23.497048] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[   23.508087] tuner' 0-0061: chip found @ 0xc2 (pvrusb2_a)
[   23.511701] wm8775' 0-001b: chip found @ 0x36 (pvrusb2_a)
[   23.524585] tveeprom 0-00a2: Hauppauge model 24019, rev C289, serial# 8567676
[   23.524590] tveeprom 0-00a2: tuner model is TCL MFPE05 2 (idx 89, type 38)
[   23.524594] tveeprom 0-00a2: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74)
[   23.524597] tveeprom 0-00a2: audio processor is CX25843 (idx 37)
[   23.524600] tveeprom 0-00a2: decoder processor is CX25843 (idx 30)
[   23.524603] tveeprom 0-00a2: has radio, has IR receiver, has no IR transmitter
[   23.524610] pvrusb2: Supported video standard(s) reported available in hardware: PAL-B/B1/D/D1/G/H/I/K;SECAM-B/D/G/H/K/K
[   23.524616] pvrusb2: Mapping standards mask=0xff00ff (PAL-B/B1/D/D1/G/H/I/K;SECAM-B/D/G/H/K/K1/L/LC)
[   23.524619] pvrusb2: Setting up 20 unique standard(s)
[   23.524624] pvrusb2: Set up standard idx=0 name=PAL-B/G
[   23.524627] pvrusb2: Set up standard idx=1 name=PAL-D/K
[   23.524630] pvrusb2: Set up standard idx=2 name=SECAM-B/G
[   23.524632] pvrusb2: Set up standard idx=3 name=SECAM-D/K
[   23.524635] pvrusb2: Set up standard idx=4 name=PAL-B
[   23.524638] pvrusb2: Set up standard idx=5 name=PAL-B1
[   23.524640] pvrusb2: Set up standard idx=6 name=PAL-G
[   23.524643] pvrusb2: Set up standard idx=7 name=PAL-H
[   23.524646] pvrusb2: Set up standard idx=8 name=PAL-I
[   23.524648] pvrusb2: Set up standard idx=9 name=PAL-D
[   23.524651] pvrusb2: Set up standard idx=10 name=PAL-D1
[   23.524653] pvrusb2: Set up standard idx=11 name=PAL-K
[   23.524656] pvrusb2: Set up standard idx=12 name=SECAM-B
[   23.524659] pvrusb2: Set up standard idx=13 name=SECAM-D
[   23.524661] pvrusb2: Set up standard idx=14 name=SECAM-G
[   23.524664] pvrusb2: Set up standard idx=15 name=SECAM-H
[   23.524667] pvrusb2: Set up standard idx=16 name=SECAM-K
[   23.524669] pvrusb2: Set up standard idx=17 name=SECAM-K1
[   23.524672] pvrusb2: Set up standard idx=18 name=SECAM-L
[   23.524675] pvrusb2: Set up standard idx=19 name=SECAM-LC
[   23.524678] pvrusb2: Initial video standard auto-selected to PAL-B/G
[   23.524690] pvrusb2: Device initialization completed successfully.
[   23.524921] pvrusb2: registered device video0 [mpeg]
[   23.525005] pvrusb2: registered device radio0 [mpeg]
[   23.533495] firmware: requesting v4l-cx25840.fw


It does seem to load but then it requests the firmware again? Does anyone know how to fix this? I found a workaround for pvr-usb2 for earlier kernels but that does not work on 2.6.27-14.

/Per

krys

  • Addicted
  • *
  • Posts: 583
    • View Profile
Re: pvr-usb2 not working in 810 alpha 2.29
« Reply #1 on: August 31, 2009, 06:21:42 pm »
I seem to be experiencing this same issue, hopefully someone can help us out.
-Krys