|
rages
|
 |
« on: June 20, 2009, 10:04:17 am » |
|
Hi,
I have noticed that with LinuxMCE 8.10 don't working the steps to install the drivers of 3M touch screen, then I tried to use those in reposity Ubuntu 8.10 but nothing works I have also changed xorg.conf as I was advised in a forum but does not work.
You have some ideas on what to do?
|
|
|
|
« Last Edit: August 28, 2009, 08:56:54 am by rages »
|
Logged
|
|
|
|
|
|
|
dlewis
|
|
« Reply #2 on: August 28, 2009, 12:03:46 pm » |
|
please create a wiki for these devices... Title the wiki "3M Touch Screens" and add some pictures.
|
|
|
|
|
Logged
|
|
|
|
|
rages
|
|
« Reply #3 on: August 28, 2009, 12:42:11 pm » |
|
ok, when I have just a moment ... my problem is to write well in English, if there are error correct them.
Emanuele
|
|
|
|
|
Logged
|
|
|
|
|
dlewis
|
|
« Reply #4 on: August 28, 2009, 12:45:23 pm » |
|
yes, I will correct your wiki page if need be  |
|
|
|
|
Logged
|
|
|
|
|
Nuwis
|
|
« Reply #5 on: October 11, 2009, 07:59:46 am » |
|
Dear All,
Iīm thinking to get one of this, whatīs better Serial or USB? I thinking in the M1700SS 17" monitor.
Cheers
|
|
|
|
|
Logged
|
|
|
|
|
rages
|
|
« Reply #6 on: October 11, 2009, 01:00:35 pm » |
|
hi,
I bought the serial, as it was available that, do not deny that I had some problems with LinuxMCE 7.10 because the automatic recognition serial blocked the touch. In version 8.10 once the drivers are installed correctly everything works fine.
Emanuele
|
|
|
|
|
Logged
|
|
|
|
|
Nuwis
|
|
« Reply #7 on: October 11, 2009, 03:14:13 pm » |
|
Hi again,
I have another question regarding that.
If i have some drivers or modules to load for this screen, can i do a diskless boot? and when and from where are the drivers load?
I think in this case is the same question like another drivers that should be loaded indepedent from the LinuxMCE system.
In resume and going out a litle bit out from the main post, if i need to load another drivers outside from the LinuxMCE what i need to do? Install Kubuntu in the MD and load the drivers in?
Every time i tryed to do that never had started the MD, in the first boot later to install LinuxMCE from Kubuntu, and the LinuxMCE installed had detected the Core and i answered that this PC is a MD, i get some errors and at the end starts Kubuntu but no LinuxMCE.
I think i had deviated the post, if itīs this case i will open a new post.
Thnks in advance
|
|
|
|
|
Logged
|
|
|
|
|
rages
|
|
« Reply #8 on: October 11, 2009, 07:04:46 pm » |
|
Hi,
I do not know if I understand your request, however with regard to the drivers of the touch I'll explain how I did.
I use a touch with a diskless Atom N330, I created the MD normally and then I open KDE and a system terminal, I have downloaded the drivers and I have installed directly on MD.
I have also tried to install them from the core with chroot but doesn't work, the installation hangs.
Emanuele
|
|
|
|
|
Logged
|
|
|
|
|
