Author Topic: HSM100 / EZMotion Triple Sensor  (Read 3888 times)

Kooma

  • Veteran
  • ***
  • Posts: 102
    • View Profile
HSM100 / EZMotion Triple Sensor
« on: September 05, 2009, 02:01:09 pm »
Hi. I'd like to know the present support situation for this unit. Checked the forums to found few short/dead threads on this.
I'm planning on buying few of these, if they're supported. Based on my experience, I'll setup also a wiki page for these sensors. That's about all I can contribute at the moment..
Thanks for your comments.

apagg

  • Veteran
  • ***
  • Posts: 60
    • View Profile
Re: HSM100 / EZMotion Triple Sensor
« Reply #1 on: October 23, 2009, 08:50:49 am »
I am trying to get the EZmotion to work but have had no luck so far. It registers as a climate device, but the status i blank and I cant use it to make a scenario. I am using 810beta

totallymaxed

  • LinuxMCE God
  • ****
  • Posts: 4660
  • Smart Home Consulting
    • View Profile
    • Dianemo - at home with technology
Re: HSM100 / EZMotion Triple Sensor
« Reply #2 on: October 23, 2009, 09:35:58 am »
I am trying to get the EZmotion to work but have had no luck so far. It registers as a climate device, but the status i blank and I cant use it to make a scenario. I am using 810beta

Hari is person to really respond to this...but my understanding was that at least part of the support for the EZmotion multi-sensor was in place in the 0810 ZWave binaries. We have an EZmotion here somewhere...so I will see if I can dig it out and do some tests.

All the best

Andrew
Andy Herron,
CHT Ltd

For Dianemo/LinuxMCE consulting advice;
@herron on Twitter, totallymaxed+inquiries@gmail.com via email or PM me here.

Get Dianemo-Rpi2 ARM Licenses http://forum.linuxmce.org/index.php?topic=14026.0

Get RaspSqueeze-CEC or Raspbmc-CEC for Dianemo/LinuxMCE: http://wp.me/P4KgIc-5P

Facebook: https://www.facebook.com/pages/Dianemo-Home-Automation/226019387454465

http://www.dianemo.co.uk

apagg

  • Veteran
  • ***
  • Posts: 60
    • View Profile
Re: HSM100 / EZMotion Triple Sensor
« Reply #3 on: October 23, 2009, 01:33:50 pm »
I have been looking in the svn and found some changes to the z-wave system http://svn.linuxmce.org/trac.cgi/changeset/22238 Is this maybe a fix? In that case how can I install it?

apagg

  • Veteran
  • ***
  • Posts: 60
    • View Profile
Re: HSM100 / EZMotion Triple Sensor
« Reply #4 on: December 03, 2009, 09:51:35 am »
After updating to beta2 I still have the same issues. I don't mind trying to make some new templates for this device if that is needed. Can anyone confirm that they are needed?

I have also bought a Horstmann AS2 RF, but I can't make it a part for my network. Does anyone use this device successfully or have any hints on how to get it to work? 

totallymaxed

  • LinuxMCE God
  • ****
  • Posts: 4660
  • Smart Home Consulting
    • View Profile
    • Dianemo - at home with technology
Re: HSM100 / EZMotion Triple Sensor
« Reply #5 on: December 03, 2009, 10:29:34 am »
After updating to beta2 I still have the same issues. I don't mind trying to make some new templates for this device if that is needed. Can anyone confirm that they are needed?

I have also bought a Horstmann AS2 RF, but I can't make it a part for my network. Does anyone use this device successfully or have any hints on how to get it to work? 

Our EZmotion suffered a failure so I am waiting for the replacement to arrive then i will run a test here.

All the best


Andrew
Andy Herron,
CHT Ltd

For Dianemo/LinuxMCE consulting advice;
@herron on Twitter, totallymaxed+inquiries@gmail.com via email or PM me here.

Get Dianemo-Rpi2 ARM Licenses http://forum.linuxmce.org/index.php?topic=14026.0

Get RaspSqueeze-CEC or Raspbmc-CEC for Dianemo/LinuxMCE: http://wp.me/P4KgIc-5P

Facebook: https://www.facebook.com/pages/Dianemo-Home-Automation/226019387454465

http://www.dianemo.co.uk