General > Users
Raspberry Pi as UPnP player under Dianemo
bulek:
Hello,
I'm trying to setup RPi with raspbmc as UPnP player that can be controlled from Dianemo.
Have three short questions :
1. What do I put into /etc/pluto/media_config.conf for RPi ? Is this right ?
--- Code: ---#XBMC RPi
Room=12: AudioDev=412; VideoDev=412; KeepScreenOnForOSD=no
--- End code ---
2. How to troubleshoot setup it it isn't working ?
3. If I want to start media from XBMC GUI - what is the proper way to get media from Dianemo ? UPnP server LS doesn't provide video files, also music files are not working for me, should Samba be used for this ?
Thanks in advance,
regards,
Bulek.
totallymaxed:
--- Quote from: bulek on February 10, 2014, 11:26:06 pm ---Hello,
I'm trying to setup RPi with raspbmc as UPnP player that can be controlled from Dianemo.
Have three short questions :
1. What do I put into /etc/pluto/media_config.conf for RPi ? Is this right ?
--- Code: ---#XBMC RPi
Room=12: AudioDev=412; VideoDev=412; KeepScreenOnForOSD=no
--- End code ---
2. How to troubleshoot setup it it isn't working ?
3. If I want to start media from XBMC GUI - what is the proper way to get media from Dianemo ? UPnP server LS doesn't provide video files, also music files are not working for me, should Samba be used for this ?
Thanks in advance,
regards,
Bulek.
--- End quote ---
See http://wiki.linuxmce.org/index.php/Dianemo_S#Configuring_Media_Config for details of media_config. If the Rpi is attached to a TV and the audio will come from the TV's onboard speakers then the AudioDev would be the TV device as you will want the audio commands to be sent to the TV (ie CEC or IP control of TV). If the TV is not controllable then you can use the AppServer device in the room that the Rpi/TV is located as this has a facility to react to audio commands and route those to Alsa. If the audio will be routed via an amplifier, and the amplifier has rs-232 or IP control then you would use the dev ID of the Amplifier as the audio control commands would need to be routed to the Amp. In all cases the VideoDev would be the the Rpi.
In most cases any problems can be resolved by double checking that you are routing the appropriate commands to the correct devices.
To pull media from XBMC's GUI you would use either UPnP mode (set this in Web Admin) or you could use Samba. UPnP is usually better because the UPnP server will organise your media for you. When you pull media from XBMC Dianemo will not know that media is 'playing' so you will not get any indication of this on your Orbiters. However if you set your Orbiter to the room where media playback has been started via XBMC's UI you should be able to control the playback from your Orbiter still.
If you use our Rpi firmware you also get CEC control integration to from Dianemo.
All the best
Andy
Homeboy:
Hi Andrew,
How can I get the firmware of Dianemo for my Rpi.
Thanks,
Heinz
bulek:
Hi,
I'm back to this problem. I intend to replace my MD with RPi and rasbmc image.
I've followed instructions on Wiki page closely, but I must be doing something wrong. I've added upnp plugin and upnp device...
Situation is like this:
- if I start media from within XBMC then I can pause it from Orbiter (if in correct room)
- but if I start media from Orbiter it won't start on RPi (nothing happens)
What I didn't clearly seen is that option of choosing upnp or samba mode when first going into Video or Audio browser. Also I don't know how to do this "... you would use either UPnP mode (set this in Web Admin)...".
There is something still missing here - please can you help me ? Media config is written above - is it right to setup upnp player device for both Audio and Video commands ?
Also another question: from inside XBMC - will it find media from Dianemo as upnp server or should I access media via samba server ?
Thanks in advance,
regards,
Bulek.
totallymaxed:
--- Quote from: bulek on August 23, 2014, 04:05:51 am ---Hi,
I'm back to this problem. I intend to replace my MD with RPi and rasbmc image.
I've followed instructions on Wiki page closely, but I must be doing something wrong. I've added upnp plugin and upnp device...
Situation is like this:
- if I start media from within XBMC then I can pause it from Orbiter (if in correct room)
- but if I start media from Orbiter it won't start on RPi (nothing happens)
What I didn't clearly seen is that option of choosing upnp or samba mode when first going into Video or Audio browser. Also I don't know how to do this "... you would use either UPnP mode (set this in Web Admin)...".
There is something still missing here - please can you help me ? Media config is written above - is it right to setup upnp player device for both Audio and Video commands ?
Also another question: from inside XBMC - will it find media from Dianemo as upnp server or should I access media via samba server ?
Thanks in advance,
regards,
Bulek.
--- End quote ---
To set upnp mode from web admin;
Wizards->Basic Info->Installation->'enable upnp media browsing'
Make sure there is no MM in the room your RPi is in.
Yes Rpi can be set for video/audio commands if no controlled amplifier is in use in the room.
Andy
Navigation
[0] Message Index
[#] Next page
Go to full version