heres some new logs, I attempted multiple outgoing calls with no success, they all hung up after 3 rings

Just an update.
I tried to call the Gvoice number, my sipsoft phone shows the call and i can answer it
but the caller hears ringing only then they get the Gtalk voicemail.

i just called it a patch , but what i did was remove the old and put in the new

So when i start myth tv, it will randomly switch between watch tv, recordings and a number one on screen.
it will then ask me if i want to reset the backend, i say yes, it then says it can not connect to the back end.

I put your patch in (db_phone_config.sh) now it does not show a status and i can not add a sip soft phone to test.
when i add a sip soft phone in the LMCE admin page, there is no profiled ext or password

Ok after putting the username in the phone number filed, it show connected but i can not make outgoing calls, they just ring endlessly.

asterisk log full:
[Dec 24 16:25:23] NOTICE[23736] iax2-provision.c: No IAX provisioning configuration found, IAX provisioning disabled.
[Dec 24 16:26:18] VERBOSE[25259] chan_gtalk.c: OOOOH domain = riggsusa
[Dec 24 16:27:00] VERBOSE[26875] chan_gtalk.c: OOOOH domain = riggsusa
[Dec 24 16:27:50] WARNING[2379] chan_sip.c: No valid transports available, falling back to 'udp'.
[Dec 24 16:27:50] NOTICE[28066] chan_iax2.c: Ignoring bindport on reload
[Dec 24 16:27:50] NOTICE[28066] chan_iax2.c: Ignoring bindaddr on reload
[Dec 24 16:27:50] NOTICE[28066] iax2-provision.c: No IAX provisioning configuration found, IAX provisioning disabled.
[Dec 24 16:28:19] WARNING[29142] pbx.c: Extension 'vmx', priority 54 in 'macro-vm', label 'vmxopts' already in use at priority 52
[Dec 24 16:28:19] WARNING[2379] chan_sip.c: No valid transports available, falling back to 'udp'.
[Dec 24 16:29:23] WARNING[30382] pbx.c: Extension 'vmx', priority 54 in 'macro-vm', label 'vmxopts' already in use at priority 52
[Dec 24 16:29:23] WARNING[2379] chan_sip.c: No valid transports available, falling back to 'udp'.
[Dec 24 16:29:25] VERBOSE[30388] chan_gtalk.c: OOOOH domain = riggsusa

So we don't enter a phone number..
There needs to be a HowTo for this or the script needs to change to allow for the correct values.

it looks like you are putting your username in the phone number section

I've been playing with this for weeks and I have got no where.
As for filling out the username with @gmail.com does not change a damn thing, as for it saving the settings it is hit and miss

I'm in contact with Elk Products, to see if they will send me an updated version, I have a account with them from my installer days, I just never thought about it till now.

Yeah it sucks but I can't help where it is, I just found it.

For any one interested I came across this link for the Elk M1 Gold Rs232 protocol Specs.

http://www.scribd.com/doc/50097012/Elk-m1-Rs232-Protocol

Its a old Dell XPS gen5,
I can confirm that the power line signals are transmitting and receiving, but I'm not getting anywhere with RF which is the only reason I use X10 now.
 

I have to do some RF tests but so far i think that fixed it i can send PL commands, I cant seem to get a response over RF maybe due a config error on my part

I'm in the USA I only use the CM15A for RF motion sensors although i know i have good communication over PL.
I just did a test in windows and AHP work as usual