In my prayers too Thom!
Dennis

l3mce,
grabbed your file and substituded it for existing Utils.sh    System detected and set up correct driver, however I had something else wrong as the avwizard failed to run even if forced.

I downloaded the lasted (recommended) dvd image and re-installed... then substituted your Utils.sh  ... AVWizard ran correctly (however it runs twice back-to-back for some reason), then the system finished installing.

Thanks

Dennis

actually.. if you rebuild the TBZ image, then for a fresh MD from that.. you can rebuild the image from the web admin page (media directors).  then on boot of the MD, it will re-build everything based on settings already in the database for that MD. (at least that is what I have observed)

Dennis

have grabbed your file... will test it on next reboot sometime later today.

Thanks

Dennis

okay..  I was adding additional items to the video detection section of Utils.sh (added new item for ATI driver 'ati' and 'mach64')   on bootup, the system identifies my display as requiring the 'ati' driver (identified in yellow text)... but continues to flicker... unable to launch AVWizard.. non-stop I might add



If i put a valid xorg.conf file in /etc/X11 on bootup there is the yellow text stating the 'ati' driver IS installed... but still cannot either run AVWizard or the orbiter... however I may sometimes get a 'cannot configure X' screen (or something along those lines).


For now, I have to kill all the AVWizard and X -config programs and then launch startx to get into myth setup (my dvb cards are in my core)

Any suggestions on how to get my orbiter working again or get the AVWizard to launch correctly?

Dennis

Mythtv with HDPVR bringing in DirecTV (soon to be dropped), WinTV-HD-S2 connected to MiniBud C/Ku motorized dish, and a HD-5500 bringing in OTA.

Dennis

Here is the lspci -nnv output for the ATI Rage XL card:

03:06.0 VGA compatible controller [0300]: ATI Technologies Inc Rage XL [1002:4752] (rev 27)
        Subsystem: ATI Technologies Inc Device [1002:8008]
        Flags: bus master, stepping, medium devsel, latency 64, IRQ 11
        Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
        I/O ports at b000 [size=256]
        Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
        Expansion ROM at feac0000 [disabled] [size=128K]
        Capabilities: [5c] Power Management version 2
        Kernel modules: atyfb

Xorg document dated Feb 2012:  http://www.x.org/releases/X11R7.5/doc/ati.html

According to the document there is an 'ati' driver for use with this chipset.  

the xserver-xorg-video-ati package IS already installed.   There is a driver named ati_drv.so AND a driver named mach64_drv.so in /usr/lib/xorg/modules/drivers


With Driver  "ati"   set in xorg.conf  running startx brings up the kde desktop.   here is output of Xorg.0.log:

Code:

X.Org X Server 1.7.6
Release Date: 2010-03-17
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-29-server i686 Ubuntu
Current Operating System: Linux dcerouter 2.6.32-40-generic-pae #87-Ubuntu SMP Mon Mar 5 21:44:34 UTC 2012 i686
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-40-generic-pae root=UUID=a698baa3-0241-4042-96f8-d186b58407b2 ro quiet
Build Date: 25 February 2012  06:59:39AM
xorg-server 2:1.7.6-2ubuntu7.11 (For technical support please see http://www.ubuntu.com/support)
Current version of pixman: 0.21.4
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Mar 24 09:02:20 2012
(==) Using config file: "/etc/X11/xorg.conf"
(==) Using config directory: "/usr/lib/X11/xorg.conf.d"
(==) ServerLayout "X.org Configured"
(**) |-->Screen "Screen0" (0)
(**) |   |-->Monitor "Monitor0"
(**) |   |-->Device "Card0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
Entry deleted from font path.
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
Entry deleted from font path.
(**) FontPath set to:
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType,
built-ins,
/usr/share/fonts/X11/misc,
/usr/share/fonts/X11/100dpi/:unscaled,
/usr/share/fonts/X11/75dpi/:unscaled,
/usr/share/fonts/X11/Type1,
/usr/share/fonts/X11/100dpi,
/usr/share/fonts/X11/75dpi,
/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType,
built-ins
(**) ModulePath set to "/usr/lib/xorg/modules"
(WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
(WW) Disabling Mouse0
(WW) Disabling Keyboard0
(II) Loader magic: 0x81f0e80
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 6.0
X.Org XInput driver : 7.0
X.Org Server Extension : 2.0
(--) using VT number 1

(--) PCI: (0:1:3:0) 14f1:8800:0070:6906 Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder rev 5, Mem @ 0xf0000000/16777216
(--) PCI: (0:2:3:0) 14f1:8800:7063:5500 Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder rev 5, Mem @ 0xf8000000/16777216
(--) PCI:*(0:3:6:0) 1002:4752:1002:8008 ATI Technologies Inc Rage XL rev 39, Mem @ 0xfd000000/16777216, 0xfeaff000/4096, I/O @ 0x0000b000/256, BIOS @ 0x????????/131072
(II) Open ACPI successful (/var/run/acpid.socket)
(II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
(II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
(II) "glx" will be loaded. This was enabled by default and also specified in the config file.
(II) "record" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri" will be loaded. This was enabled by default and also specified in the config file.
(II) "dri2" will be loaded. This was enabled by default and also specified in the config file.
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions/librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions/libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions/libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.0.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.1.0
ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) LoadModule: "ati"
(II) Loading /usr/lib/xorg/modules/drivers/ati_drv.so
(II) Module ati: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 6.13.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) LoadModule: "mach64"
(II) Loading /usr/lib/xorg/modules/drivers/mach64_drv.so
(II) Module mach64: vendor="X.Org Foundation"
compiled for 1.7.2, module version = 6.8.2
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 6.0
(II) MACH64: Driver for ATI Mach64 chipsets
(II) Primary Device is: PCI 03@00:06:0
(==) MACH64(0): Depth 24, (--) framebuffer bpp 32
(==) MACH64(0): Using XAA acceleration architecture
(II) MACH64: Mach64 in slot 3:6:0 detected.
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules/libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.0.0
ABI class: X.Org Video Driver, version 6.0
(II) MACH64(0): Primary V_BIOS segment is: 0xc000
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules/libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.1.0
ABI class: X.Org Video Driver, version 6.0
(II) MACH64(0): VESA BIOS detected
(II) MACH64(0): VESA VBE Version 2.0
(II) MACH64(0): VESA VBE Total Mem: 8128 kB
(II) MACH64(0): VESA VBE OEM: ATI MACH64
(II) MACH64(0): VESA VBE OEM Software Rev: 1.0
(II) MACH64(0): VESA VBE OEM Vendor: ATI Technologies Inc.
(II) MACH64(0): VESA VBE OEM Product: MACH64GM
(II) MACH64(0): VESA VBE OEM Product Rev: 01.00
(II) MACH64(0): VESA VBE DDC supported
(II) MACH64(0): VESA VBE DDC Level 2
(II) MACH64(0): VESA VBE DDC transfer in appr. 2 sec.
(II) MACH64(0): VESA VBE DDC read successfully
(II) MACH64(0): Manufacturer: SAM  Model: 191  Serial#: 1112092983
(II) MACH64(0): Year: 2005  Week: 11
(II) MACH64(0): EDID Version: 1.3
(II) MACH64(0): Analog Display Input,  Input Voltage Level: 0.700/0.300 V
(II) MACH64(0): Sync:  Separate  Composite  SyncOnGreen
(II) MACH64(0): Max Image Size [cm]: horiz.: 34  vert.: 27
(II) MACH64(0): Gamma: 2.20
(II) MACH64(0): DPMS capabilities: Off; RGB/Color Display
(II) MACH64(0): First detailed timing is preferred mode
(II) MACH64(0): redX: 0.650 redY: 0.330   greenX: 0.330 greenY: 0.600
(II) MACH64(0): blueX: 0.150 blueY: 0.080   whiteX: 0.313 whiteY: 0.329
(II) MACH64(0): Supported established timings:
(II) MACH64(0): 720x400@70Hz
(II) MACH64(0): 640x480@60Hz
(II) MACH64(0): 640x480@67Hz
(II) MACH64(0): 640x480@72Hz
(II) MACH64(0): 640x480@75Hz
(II) MACH64(0): 800x600@56Hz
(II) MACH64(0): 800x600@60Hz
(II) MACH64(0): 800x600@72Hz
(II) MACH64(0): 800x600@75Hz
(II) MACH64(0): 832x624@75Hz
(II) MACH64(0): 1024x768@60Hz
(II) MACH64(0): 1024x768@70Hz
(II) MACH64(0): 1024x768@75Hz
(II) MACH64(0): 1280x1024@75Hz
(II) MACH64(0): 1152x864@75Hz
(II) MACH64(0): Manufacturer's mask: 0
(II) MACH64(0): Supported standard timings:
(II) MACH64(0): #0: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
(II) MACH64(0): #1: hsize: 1280  vsize 960  refresh: 60  vid: 16513
(II) MACH64(0): #2: hsize: 1152  vsize 864  refresh: 75  vid: 20337
(II) MACH64(0): Supported detailed timing:
(II) MACH64(0): clock: 108.0 MHz   Image Size:  338 x 270 mm
(II) MACH64(0): h_active: 1280  h_sync: 1328  h_sync_end 1440 h_blank_end 1688 h_border: 0
(II) MACH64(0): v_active: 1024  v_sync: 1025  v_sync_end 1028 v_blanking: 1066 v_border: 0
(II) MACH64(0): Ranges: V min: 56 V max: 75 Hz, H min: 30 H max: 81 kHz, PixClock max 140 MHz
(II) MACH64(0): Monitor name: SyncMaster
(II) MACH64(0): Serial No: HCJY329690
(II) MACH64(0): EDID (in hex):
(II) MACH64(0): 00ffffffffffff004c2d910137314942
(II) MACH64(0): 0b0f01030e221b782aaaa5a654549926
(II) MACH64(0): 145054bfef8081808140714f01010101
(II) MACH64(0): 010101010101302a009851002a403070
(II) MACH64(0): 1300520e1100001e000000fd00384b1e
(II) MACH64(0): 510e000a202020202020000000fc0053
(II) MACH64(0): 796e634d61737465720a2020000000ff
(II) MACH64(0): 0048434a593332393639300a20200076
(II) MACH64(0): EDID vendor "SAM", prod id 401
(II) MACH64(0): Using hsync ranges from config file
(II) MACH64(0): Using vrefresh ranges from config file
(II) MACH64(0): Printing DDC gathered Modelines:
(II) MACH64(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(II) MACH64(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(II) MACH64(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(II) MACH64(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(II) MACH64(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(II) MACH64(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz)
(II) MACH64(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(II) MACH64(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(II) MACH64(0): Modeline "1280x1024"x0.0  135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync (80.0 kHz)
(II) MACH64(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(II) MACH64(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(II) MACH64(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(II) MACH64(0): Modeline "832x624"x0.0   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz)
(II) MACH64(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(II) MACH64(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(II) MACH64(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(II) MACH64(0): Modeline "1280x960"x0.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz)
(II) MACH64(0): BIOS Data:  BIOSSize=0x8000, ROMTable=0x0114.
(II) MACH64(0): BIOS Data:  ClockTable=0x097C, FrequencyTable=0x0000.
(II) MACH64(0): BIOS Data:  LCDTable=0x0000.
(II) MACH64(0): BIOS Data:  VideoTable=0x0000, HardwareTable=0x015E.
(II) MACH64(0): BIOS Data:  I2CType=0x0F, Tuner=0x00, Decoder=0x00, Audio=0x0F.
(--) MACH64(0): ATI 3D Rage XL or XC graphics controller detected.
(--) MACH64(0): Chip type 4752 "GR", version 7, foundry TSMC, class 0, revision 0x00.
(--) MACH64(0): PCI bus interface detected;  block I/O base is 0xB000.
(--) MACH64(0): ATI Mach64 adapter detected.
(!!) MACH64(0): For information on using the multimedia capabilities
of this adapter, please see http://gatos.sf.net.
(--) MACH64(0): Internal RAMDAC (subtype 1) detected.
(==) MACH64(0): RGB weight 888
(==) MACH64(0): Default visual is TrueColor
(==) MACH64(0): Using gamma correction (1.0, 1.0, 1.0)
(II) MACH64(0): Using Mach64 accelerator CRTC.
(II) MACH64(0): Storing hardware cursor image at 0xFD7FFC00.
(II) MACH64(0): Using 8 MB linear aperture at 0xFD000000.
(!!) MACH64(0): Virtual resolutions will be limited to 8191 kB
 due to linear aperture size and/or placement of hardware cursor image area.
(II) MACH64(0): Using Block 0 MMIO aperture at 0xFEAFF400.
(II) MACH64(0): Using Block 1 MMIO aperture at 0xFEAFF000.
(II) MACH64(0): MMIO write caching enabled.
(--) MACH64(0): 8192 kB of SGRAM (2:1) 32-bit detected (using 8191 kB).
(WW) MACH64(0): Cannot shadow an accelerated frame buffer.
(II) MACH64(0): Engine XCLK 62.353 MHz;  Refresh rate code 1.
(--) MACH64(0): Internal programmable clock generator detected.
(--) MACH64(0): Reference clock 157.5/11 (14.318) MHz.
(II) MACH64(0): Monitor0: Using hsync range of 30.00-81.00 kHz
(II) MACH64(0): Monitor0: Using vrefresh range of 56.00-75.00 Hz
(II) MACH64(0): Monitor0: Using maximum pixel clock of 140.00 MHz
(II) MACH64(0): Estimated virtual size for aspect ratio 1.2593 is 1280x1024
(II) MACH64(0): Maximum clock: 124.00 MHz
(II) MACH64(0): Not using default mode "640x350" (vrefresh out of range)
(II) MACH64(0): Not using default mode "320x175" (vrefresh out of range)
(II) MACH64(0): Not using default mode "640x400" (vrefresh out of range)
(II) MACH64(0): Not using default mode "320x200" (vrefresh out of range)
(II) MACH64(0): Not using default mode "720x400" (vrefresh out of range)
(II) MACH64(0): Not using default mode "360x200" (vrefresh out of range)
(II) MACH64(0): Not using default mode "640x480" (vrefresh out of range)
(II) MACH64(0): Not using default mode "320x240" (vrefresh out of range)
(II) MACH64(0): Not using default mode "800x600" (vrefresh out of range)
(II) MACH64(0): Not using default mode "400x300" (vrefresh out of range)
(II) MACH64(0): Not using default mode "1024x768" (vrefresh out of range)
(II) MACH64(0): Not using default mode "512x384" (vrefresh out of range)
(II) MACH64(0): Not using default mode "1024x768" (vrefresh out of range)
(II) MACH64(0): Not using default mode "512x384" (vrefresh out of range)
(II) MACH64(0): Not using default mode "1280x960" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "640x480" (hsync out of range)
(II) MACH64(0): Not using default mode "1280x1024" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "1280x1024" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "640x512" (hsync out of range)
(II) MACH64(0): Not using default mode "1600x1200" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1600x1200" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1600x1200" (width too large for virtual size)
(II) MACH64(0): Not using default mode "800x600" (hsync out of range)
(II) MACH64(0): Not using default mode "1600x1200" (width too large for virtual size)
(II) MACH64(0): Not using default mode "800x600" (hsync out of range)
(II) MACH64(0): Not using default mode "1600x1200" (width too large for virtual size)
(II) MACH64(0): Not using default mode "800x600" (hsync out of range)
(II) MACH64(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) MACH64(0): Not using default mode "896x672" (hsync out of range)
(II) MACH64(0): Not using default mode "1792x1344" (insufficient memory for mode)
(II) MACH64(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) MACH64(0): Not using default mode "928x696" (hsync out of range)
(II) MACH64(0): Not using default mode "1856x1392" (insufficient memory for mode)
(II) MACH64(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) MACH64(0): Not using default mode "960x720" (hsync out of range)
(II) MACH64(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) MACH64(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "1152x864" (vrefresh out of range)
(II) MACH64(0): Not using default mode "576x432" (vrefresh out of range)
(II) MACH64(0): Not using default mode "1152x864" (vrefresh out of range)
(II) MACH64(0): Not using default mode "576x432" (vrefresh out of range)
(II) MACH64(0): Not using default mode "1152x864" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "576x432" (hsync out of range)
(II) MACH64(0): Not using default mode "1360x768" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1360x768" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1400x1050" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1400x1050" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1400x1050" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1400x1050" (width too large for virtual size)
(II) MACH64(0): Not using default mode "700x525" (hsync out of range)
(II) MACH64(0): Not using default mode "1440x900" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1600x1024" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1680x1050" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1680x1050" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1680x1050" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1680x1050" (width too large for virtual size)
(II) MACH64(0): Not using default mode "840x525" (hsync out of range)
(II) MACH64(0): Not using default mode "1680x1050" (width too large for virtual size)
(II) MACH64(0): Not using default mode "840x525" (hsync out of range)
(II) MACH64(0): Not using default mode "1920x1080" (width too large for virtual size)
(II) MACH64(0): Not using default mode "1920x1200" (insufficient memory for mode)
(II) MACH64(0): Not using default mode "1920x1440" (insufficient memory for mode)
(II) MACH64(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "2048x1536" (insufficient memory for mode)
(II) MACH64(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "2048x1536" (insufficient memory for mode)
(II) MACH64(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using default mode "2048x1536" (insufficient memory for mode)
(II) MACH64(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) MACH64(0): Not using driver mode "1280x1024" (bad mode clock/interlace/doublescan)
(--) MACH64(0): Virtual size is 1280x1024 (pitch 1280)
(**) MACH64(0): *Driver mode "1280x1024": 108.0 MHz, 64.0 kHz, 60.0 Hz
(II) MACH64(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(**) MACH64(0): *Default mode "1280x1024": 108.0 MHz, 64.0 kHz, 60.0 Hz
(II) MACH64(0): Modeline "1280x1024"x60.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
(**) MACH64(0): *Driver mode "1280x960": 108.0 MHz, 60.0 kHz, 60.0 Hz
(II) MACH64(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz)
(**) MACH64(0): *Default mode "1280x960": 108.0 MHz, 60.0 kHz, 60.0 Hz
(II) MACH64(0): Modeline "1280x960"x60.0  108.00  1280 1376 1488 1800  960 961 964 1000 +hsync +vsync (60.0 kHz)
(**) MACH64(0): *Driver mode "1152x864": 108.0 MHz, 67.5 kHz, 75.0 Hz
(II) MACH64(0): Modeline "1152x864"x75.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(**) MACH64(0): *Default mode "1152x864": 108.0 MHz, 67.5 kHz, 75.0 Hz
(II) MACH64(0): Modeline "1152x864"x75.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
(**) MACH64(0): *Default mode "1152x864": 105.0 MHz, 67.6 kHz, 75.0 Hz
(II) MACH64(0): Modeline "1152x864"x75.0  104.99  1152 1224 1352 1552  864 865 868 902 -hsync +vsync (67.6 kHz)
(**) MACH64(0): *Default mode "1152x864": 96.8 MHz, 63.0 kHz, 70.0 Hz
(II) MACH64(0): Modeline "1152x864"x70.0   96.77  1152 1224 1344 1536  864 865 868 900 -hsync +vsync (63.0 kHz)
(**) MACH64(0): *Default mode "1152x864": 81.6 MHz, 53.7 kHz, 60.0 Hz
(II) MACH64(0): Modeline "1152x864"x60.0   81.62  1152 1216 1336 1520  864 865 868 895 -hsync +vsync (53.7 kHz)
(**) MACH64(0): *Driver mode "1024x768": 78.8 MHz, 60.0 kHz, 75.0 Hz
(II) MACH64(0): Modeline "1024x768"x75.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(**) MACH64(0): *Driver mode "1024x768": 75.0 MHz, 56.5 kHz, 70.1 Hz
(II) MACH64(0): Modeline "1024x768"x70.1   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(**) MACH64(0): *Driver mode "1024x768": 65.0 MHz, 48.4 kHz, 60.0 Hz
(II) MACH64(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(**) MACH64(0): *Default mode "1024x768": 78.8 MHz, 60.0 kHz, 75.0 Hz
(II) MACH64(0): Modeline "1024x768"x75.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
(**) MACH64(0): *Default mode "1024x768": 75.0 MHz, 56.5 kHz, 70.1 Hz
(II) MACH64(0): Modeline "1024x768"x70.1   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
(**) MACH64(0): *Default mode "1024x768": 65.0 MHz, 48.4 kHz, 60.0 Hz
(II) MACH64(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
(**) MACH64(0): *Driver mode "832x624": 57.3 MHz, 49.7 kHz, 74.6 Hz
(II) MACH64(0): Modeline "832x624"x74.6   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz)
(**) MACH64(0): *Default mode "832x624": 57.3 MHz, 49.7 kHz, 74.6 Hz
(II) MACH64(0): Modeline "832x624"x74.6   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz)
(**) MACH64(0): *Driver mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz
(II) MACH64(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(**) MACH64(0): *Driver mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz
(II) MACH64(0): Modeline "800x600"x72.2   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(**) MACH64(0): *Driver mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz
(II) MACH64(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(**) MACH64(0): *Driver mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz
(II) MACH64(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(**) MACH64(0): *Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz
(II) MACH64(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
(**) MACH64(0): *Default mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz
(II) MACH64(0): Modeline "800x600"x72.2   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
(**) MACH64(0): *Default mode "800x600": 87.8 MHz, 81.2 kHz, 65.0 Hz (D)
(II) MACH64(0): Modeline "800x600"x65.0   87.75  800 832 928 1080  600 600 602 625 doublescan +hsync +vsync (81.2 kHz)
(**) MACH64(0): *Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz
(II) MACH64(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
(**) MACH64(0): *Default mode "800x600": 81.0 MHz, 75.0 kHz, 60.0 Hz (D)
(II) MACH64(0): Modeline "800x600"x60.0   81.00  800 832 928 1080  600 600 602 625 doublescan +hsync +vsync (75.0 kHz)
(**) MACH64(0): *Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz
(II) MACH64(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
(**) MACH64(0): *Default mode "840x525": 87.0 MHz, 76.6 kHz, 69.9 Hz (D)
(II) MACH64(0): Modeline "840x525"x69.9   87.00  840 900 988 1136  525 526 529 548 doublescan -hsync +vsync (76.6 kHz)
(**) MACH64(0): *Default mode "840x525": 73.1 MHz, 65.3 kHz, 60.0 Hz (D)
(II) MACH64(0): Modeline "840x525"x60.0   73.12  840 892 980 1120  525 526 529 544 doublescan -hsync +vsync (65.3 kHz)
(**) MACH64(0): *Default mode "700x525": 77.9 MHz, 81.5 kHz, 74.8 Hz (D)
(II) MACH64(0): Modeline "700x525"x74.8   77.90  700 732 892 956  525 526 532 545 doublescan +hsync +vsync (81.5 kHz)
(**) MACH64(0): *Default mode "700x525": 72.5 MHz, 76.5 kHz, 70.1 Hz (D)
(II) MACH64(0): Modeline "700x525"x70.1   72.53  700 748 824 948  525 525 527 546 doublescan -hsync +vsync (76.5 kHz)
(**) MACH64(0): *Default mode "700x525": 61.0 MHz, 64.9 kHz, 60.0 Hz (D)
(II) MACH64(0): Modeline "700x525"x60.0   61.00  700 744 820 940  525 526 532 541 doublescan +hsync +vsync (64.9 kHz)
(**) MACH64(0): *Default mode "640x512": 67.5 MHz, 80.0 kHz, 75.0 Hz (D)
(II) MACH64(0): Modeline "640x512"x75.0   67.50  640 648 720 844  512 512 514 533 doublescan +hsync +vsync (80.0 kHz)
(**) MACH64(0): *Default mode "640x512": 54.0 MHz, 64.0 kHz, 60.0 Hz (D)
(II) MACH64(0): Modeline "640x512"x60.0   54.00  640 664 720 844  512 512 514 533 doublescan +hsync +vsync (64.0 kHz)
(**) MACH64(0): *Default mode "720x450": 53.2 MHz, 55.9 kHz, 59.9 Hz (D)
(II) MACH64(0): Modeline "720x450"x59.9   53.25  720 760 836 952  450 451 454 467 doublescan -hsync +vsync (55.9 kHz)
(**) MACH64(0): *Driver mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz
(II) MACH64(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(**) MACH64(0): *Driver mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz
(II) MACH64(0): Modeline "640x480"x72.8   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(**) MACH64(0): *Driver mode "640x480": 30.2 MHz, 35.0 kHz, 66.7 Hz
(II) MACH64(0): Modeline "640x480"x66.7   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz)
(**) MACH64(0): *Driver mode "640x480": 25.2 MHz, 31.5 kHz, 59.9 Hz
(II) MACH64(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(**) MACH64(0): *Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz
(II) MACH64(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
(**) MACH64(0): *Default mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz
(II) MACH64(0): Modeline "640x480"x72.8   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
(**) MACH64(0): *Default mode "640x480": 54.0 MHz, 60.0 kHz, 60.0 Hz (D)
(II) MACH64(0): Modeline "640x480"x60.0   54.00  640 688 744 900  480 480 482 500 doublescan +hsync +vsync (60.0 kHz)
(**) MACH64(0): *Default mode "640x480": 25.2 MHz, 31.5 kHz, 59.9 Hz
(II) MACH64(0): Modeline "640x480"x59.9   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
(**) MACH64(0): *Driver mode "720x400": 28.3 MHz, 31.5 kHz, 70.1 Hz
(II) MACH64(0): Modeline "720x400"x70.1   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
(**) MACH64(0): *Default mode "680x384": 36.0 MHz, 47.4 kHz, 60.0 Hz (D)
(II) MACH64(0): Modeline "680x384"x60.0   36.00  680 704 720 760  384 385 390 395 doublescan +hsync -vsync (47.4 kHz)
(**) MACH64(0): *Default mode "680x384": 42.4 MHz, 47.7 kHz, 59.8 Hz (D)
(II) MACH64(0): Modeline "680x384"x59.8   42.38  680 716 784 888  384 385 390 399 doublescan -hsync +vsync (47.7 kHz)
(**) MACH64(0): *Default mode "576x432": 54.0 MHz, 67.5 kHz, 75.0 Hz (D)
(II) MACH64(0): Modeline "576x432"x75.0   54.00  576 608 672 800  432 432 434 450 doublescan +hsync +vsync (67.5 kHz)
(**) MACH64(0): *Default mode "576x432": 52.5 MHz, 67.6 kHz, 75.0 Hz (D)
(II) MACH64(0): Modeline "576x432"x75.0   52.49  576 612 676 776  432 432 434 451 doublescan -hsync +vsync (67.6 kHz)
(**) MACH64(0): *Default mode "576x432": 48.4 MHz, 63.0 kHz, 70.0 Hz (D)
(II) MACH64(0): Modeline "576x432"x70.0   48.38  576 612 672 768  432 432 434 450 doublescan -hsync +vsync (63.0 kHz)
(**) MACH64(0): *Default mode "576x432": 40.8 MHz, 53.7 kHz, 60.1 Hz (D)
(II) MACH64(0): Modeline "576x432"x60.1   40.81  576 608 668 760  432 432 434 447 doublescan -hsync +vsync (53.7 kHz)
(**) MACH64(0): *Default mode "512x384": 39.4 MHz, 60.0 kHz, 75.0 Hz (D)
(II) MACH64(0): Modeline "512x384"x75.0   39.38  512 520 568 656  384 384 386 400 doublescan +hsync +vsync (60.0 kHz)
(**) MACH64(0): *Default mode "512x384": 37.5 MHz, 56.5 kHz, 70.1 Hz (D)
(II) MACH64(0): Modeline "512x384"x70.1   37.50  512 524 592 664  384 385 388 403 doublescan -hsync -vsync (56.5 kHz)
(**) MACH64(0): *Default mode "512x384": 32.5 MHz, 48.4 kHz, 60.0 Hz (D)
(II) MACH64(0): Modeline "512x384"x60.0   32.50  512 524 592 672  384 385 388 403 doublescan -hsync -vsync (48.4 kHz)
(**) MACH64(0): *Default mode "416x312": 28.6 MHz, 49.7 kHz, 74.7 Hz (D)
(II) MACH64(0): Modeline "416x312"x74.7   28.64  416 432 464 576  312 312 314 333 doublescan -hsync -vsync (49.7 kHz)
(**) MACH64(0): *Default mode "400x300": 24.8 MHz, 46.9 kHz, 75.1 Hz (D)
(II) MACH64(0): Modeline "400x300"x75.1   24.75  400 408 448 528  300 300 302 312 doublescan +hsync +vsync (46.9 kHz)
(**) MACH64(0): *Default mode "400x300": 25.0 MHz, 48.1 kHz, 72.2 Hz (D)
(II) MACH64(0): Modeline "400x300"x72.2   25.00  400 428 488 520  300 318 321 333 doublescan +hsync +vsync (48.1 kHz)
(**) MACH64(0): *Default mode "400x300": 20.0 MHz, 37.9 kHz, 60.3 Hz (D)
(II) MACH64(0): Modeline "400x300"x60.3   20.00  400 420 484 528  300 300 302 314 doublescan +hsync +vsync (37.9 kHz)
(**) MACH64(0): *Default mode "400x300": 18.0 MHz, 35.2 kHz, 56.3 Hz (D)
(II) MACH64(0): Modeline "400x300"x56.3   18.00  400 412 448 512  300 300 301 312 doublescan +hsync +vsync (35.2 kHz)
(**) MACH64(0): *Default mode "320x240": 15.8 MHz, 37.5 kHz, 75.0 Hz (D)
(II) MACH64(0): Modeline "320x240"x75.0   15.75  320 328 360 420  240 240 242 250 doublescan -hsync -vsync (37.5 kHz)
(**) MACH64(0): *Default mode "320x240": 15.8 MHz, 37.9 kHz, 72.8 Hz (D)
(II) MACH64(0): Modeline "320x240"x72.8   15.75  320 332 352 416  240 244 246 260 doublescan -hsync -vsync (37.9 kHz)
(**) MACH64(0): *Default mode "320x240": 12.6 MHz, 31.5 kHz, 60.1 Hz (D)
(II) MACH64(0): Modeline "320x240"x60.1   12.59  320 328 376 400  240 245 246 262 doublescan -hsync -vsync (31.5 kHz)
(**) MACH64(0): Display dimensions: (340, 270) mm
(**) MACH64(0): DPI set to (95, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/lib/xorg/modules/libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 1.2.1
ABI class: X.Org Video Driver, version 6.0
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) MACH64(0): I2C bus "Mach64" initialized.
(--) Depth 24 pixmap format is 32 bpp
(WW) MACH64(0): DRI static buffer allocation failed -- need at least 12800 kB video memory
(II) MACH64(0): Largest offscreen areas (with overlaps):
(II) MACH64(0): 1280 x 614 rectangle at 0,1024
(II) MACH64(0): 256 x 615 rectangle at 0,1024
(II) MACH64(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
Indirect CPU to Screen color expansion
Solid Lines
Setting up tile and stipple cache:
20 128x128 slots
5 256x256 slots
(==) MACH64(0): Backing store disabled
(==) MACH64(0): Silken mouse enabled
(**) MACH64(0): DPMS enabled
(II) MACH64(0): Direct rendering disabled
(==) RandR enabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
(II) AIGLX: Screen 0 is not DRI capable
(II) AIGLX: Loaded and initialized /usr/lib/dri/swrast_dri.so
(II) GLX: Initialized DRISWRAST GL provider for screen 0
(II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm
(II) config/udev: Adding input device Power Button (/dev/input/event1)
(**) Power Button: Applying InputClass "evdev keyboard catchall"
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.7.6, module version = 2.3.2
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 7.0
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event1"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc105"
(**) Option "xkb_layout" "us"
(**) Option "xkb_variant" "basic"
(II) XKB: reuse xkmfile /var/lib/xkb/server-FA909DFBFFB6007765A9F4B3490F5D40DB9AB26E.xkm
(II) config/udev: Adding input device Power Button (/dev/input/event0)
(**) Power Button: Applying InputClass "evdev keyboard catchall"
(**) Power Button: always reports core events
(**) Power Button: Device: "/dev/input/event0"
(II) Power Button: Found keys
(II) Power Button: Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc105"
(**) Option "xkb_layout" "us"
(**) Option "xkb_variant" "basic"
(II) config/udev: Adding input device HID 0461:4d09 (/dev/input/event4)
(**) HID 0461:4d09: Applying InputClass "evdev pointer catchall"
(**) HID 0461:4d09: always reports core events
(**) HID 0461:4d09: Device: "/dev/input/event4"
(II) HID 0461:4d09: Found 9 mouse buttons
(II) HID 0461:4d09: Found scroll wheel(s)
(II) HID 0461:4d09: Found relative axes
(II) HID 0461:4d09: Found x and y relative axes
(II) HID 0461:4d09: Configuring as mouse
(**) HID 0461:4d09: YAxisMapping: buttons 4 and 5
(**) HID 0461:4d09: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "HID 0461:4d09" (type: MOUSE)
(II) HID 0461:4d09: initialized for relative axes.
(II) config/udev: Adding input device HID 0461:4d09 (/dev/input/mouse1)
(II) No input driver/identifier specified (ignoring)
(II) config/udev: Adding input device cx88 IR (pcHDTV HD5500 HDTV) (/dev/input/event5)
(**) cx88 IR (pcHDTV HD5500 HDTV): Applying InputClass "evdev keyboard catchall"
(**) cx88 IR (pcHDTV HD5500 HDTV): always reports core events
(**) cx88 IR (pcHDTV HD5500 HDTV): Device: "/dev/input/event5"
(II) cx88 IR (pcHDTV HD5500 HDTV): Found keys
(II) cx88 IR (pcHDTV HD5500 HDTV): Configuring as keyboard
(II) XINPUT: Adding extended input device "cx88 IR (pcHDTV HD5500 HDTV)" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc105"
(**) Option "xkb_layout" "us"
(**) Option "xkb_variant" "basic"
(II) config/udev: Adding input device cx88 IR (Hauppauge WinTV-HVR400 (/dev/input/event6)
(**) cx88 IR (Hauppauge WinTV-HVR400: Applying InputClass "evdev keyboard catchall"
(**) cx88 IR (Hauppauge WinTV-HVR400: always reports core events
(**) cx88 IR (Hauppauge WinTV-HVR400: Device: "/dev/input/event6"
(II) cx88 IR (Hauppauge WinTV-HVR400: Found keys
(II) cx88 IR (Hauppauge WinTV-HVR400: Configuring as keyboard
(II) XINPUT: Adding extended input device "cx88 IR (Hauppauge WinTV-HVR400" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc105"
(**) Option "xkb_layout" "us"
(**) Option "xkb_variant" "basic"
(II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event3)
(**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event3"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Option "xkb_model" "pc105"
(**) Option "xkb_layout" "us"
(**) Option "xkb_variant" "basic"
(II) config/udev: Adding input device Macintosh mouse button emulation (/dev/input/event2)
(**) Macintosh mouse button emulation: Applying InputClass "evdev pointer catchall"
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event2"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found relative axes
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(II) Macintosh mouse button emulation: initialized for relative axes.
(II) config/udev: Adding input device Macintosh mouse button emulation (/dev/input/mouse0)
(II) No input driver/identifier specified (ignoring)

How can I disable the 'chipset detection' during bootup and get avwizard to successfully run (or bypass avwizard)?

Dennis

I recently ran an update on my core/hybrid.. its got an onboard ati rage xl card that usually uses the mach64 kernel module... however the new installer detects the board and is trying to install the fglrx module.. it crashes.. I cant even figure out how to get it to get past this so that it finishes booting to the UI1.

Ive tried disabling my onboard video and install a PCI nVidia card... but it seems to be having issues getting it working as well

The nvidia card info is

03:00.0 VGA compatible controller [0300]: nVidia Corporation G98 [GeForce 8400 GS] [10de:06e4] (rev a1)
        Subsystem: eVga.com. Corp. Device [3842:b724]
        Flags: bus master, fast devsel, latency 0, IRQ 26
        Memory at f3000000 (32-bit, non-prefetchable) [size=16M]
        Memory at d0000000 (64-bit, prefetchable) [size=256M]
        Memory at f4000000 (64-bit, non-prefetchable) [size=32M]
        I/O ports at ac00 [size=128]
        [virtual] Expansion ROM at f67e0000 [disabled] [size=128K]
        Capabilities: [60] Power Management version 3
        Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
        Capabilities: [78] Express Endpoint, MSI 00
        Kernel driver in use: nvidia
        Kernel modules: nvidia-glx-260, nvidiafb, nouveau

I'd have to shut it down and re-enable the Rage XL card to get that info.

Dennis

Hear, Hear!

also do a web search of linuxtv and your card vendor/model... the results are usually pretty helpful.

Dennis

I have the same card.. it works with Mythtv.. yes you only need get the firmware and verify in logs that the firmware is loaded...

Have you set up a DVB-S card before?

Did you set up the 'lnb' in the DiSEqC section?   And when you are searching for channels, are you entering the transponder and SR information then searching?

And hopefully your dish is actually locked onto a satellite!!!


hope this helps...
Dennis

Jill... if you havent already... open up a new thread for the HDMI audio... there were others having problems... search the forums too!

Great that you're figuring things out though...

Dennis

Jill,
    DO NOT try making this more complicated than needed... If there is anything you ABSOLUTELY need to do on the physical 'core' machine, you are better off just going to it.... other than that.... everything you would ever really need to do on the core (management-wise) can be done remotely thru a 'terminal' (MS windows term is CMD or command prompt) OR thru the web browser interface...

You stated in another post that you set up a MD in your brother's room...   You can have a MD in your room, and you can ALSO connect your laptop or tablet to the LinuxMCE network and launch a browser to reboot any of the  MD's or the server itself.   If you have a tablet, you can make it a remote control for your MD.   The possibilities are many.

Dennis...

ps... just keep asking questions... its the only way to get the information you need!!!!!   

what 'commands' do you mean?

You can always 'ssh' remote into the server (command prompt), or you can always web administer from any web browser on your network.  I use my linux-desktop to administer my core.

Dennis

awesome!