Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - DragonK

Pages: 1 ... 25 26 [27] 28 29 30
Developers / Re: Using HADesigner: The Screencasts
« on: August 20, 2010, 04:19:43 pm »

Developers / Re: Using HADesigner: The Screencasts
« on: August 20, 2010, 04:07:36 pm »

Nope didnt work. Its only those two that seem to be the problem.

Developers / Re: Using HADesigner: The Screencasts
« on: August 20, 2010, 03:55:06 pm »

I cant view 2 of the screencasts, 02_designobj_basics_1.ogg and 04_ui2_popup_part_2.ogg. I've downloaded them twice each.
All the other screencasts work except for those two. Can you pls verify if they are indeed working.


Users / Re: wiimote on 810 alpha2
« on: August 19, 2010, 07:16:10 pm »

JUst got home.

Tested my Wiimote. After connected all lights go dead.

Maybe we should move this discussion to the users or installation issues section for other users to benefit from it to?


Developers / Re: HADesigner Screencasts: Creating the Minimo Skin
« on: August 19, 2010, 03:53:10 pm »
Hi Thom,

Are these screencasts still relevant? I wanna make my own orbiter skin\layout.
Busy downloading the screencasts at the moment.


Users / Re: wiimote on 810 alpha2
« on: August 19, 2010, 02:49:31 pm »

You using a bluetooth dongle? Can you navigate through the menu's with the directional keys on the Wiimote?

My Wiimote has the motionplus adapter, I had to remove it.
When i start the wminputd script i then only pressed 1+2 on the Wiimote. The 4 blue lights flashed then stopped. after that it was working.

You do have the wiimote's mac address in /etc/wminputd.conf?


Users / Re: wiimote on 810 alpha2
« on: August 18, 2010, 07:19:12 pm »

I use the Wiimote to its full potential without the sensor-bar, but with a usb bluetooth dongle.

Zaerc, no disrespect.

Users / Re: wiimote on 810 alpha2
« on: August 17, 2010, 09:36:56 pm »
You could try putting two candles on your TV about 20 cm (8") apart until you have a proper sensor-bar.

Zaerc or I can just read the wiki properly.........  ;D

Purps u should try this it worked for me. This is from the Wiki at the bottom......
Code: [Select]
An additional change that I need to make was in /usr/sbin/wminputd. Had the change the line wminput -c ir_ptr
 $WIIMOTE_BDADDR & to wminput $WIIMOTE_BDADDR &. Otherwise I could not move the cursor, but the buttons works.

Hope it helps. It sure did for me. I dont need to get an exspensive remote now.  8)  Or two candles ontop of my TV....  ::)

Users / Re: wiimote on 810 alpha2
« on: August 16, 2010, 07:19:42 pm »
Hi Guys,

I'm not a developer, but I just want to share my experience.

Purps, I setup a Wiimote last night using a bluetooth dongle. I followed this wiki

It works, but if I lift or drop the wiimote the cursor doesnt move, but all the buttons work. I think it might be because I dont have the sensorbar and I'm using a usb bluetooth dongle instead.


Users / Intergrate existing alarm system into LinuxMCE
« on: August 16, 2010, 11:22:43 am »
Hi All,

I want to link my existing alarm system to LinuxMCE. What do I need to look at to know if this would be possible?
Use the existing alarm panel, PIR ect......
What is the requirements of an alarm system to be able to connect to LinuxMCE?


Hi Blaine,

Sorry for the late reply, In Bed with flu.

My camera didnt autodetect. I manually added it. I still need to add it to the Wiki. Will do it today or tomorrow.

I followed this wiki at first, but instead of adding the camera as a Generic Analog camera, i chose the Generic motion Ip Camera template. If you use the path you've entered ( then you will get a refresh of still images about every 1sec.

Dont follow the examples of the Axis camera. I've attached a screenshot of my camera's device data section.
After you've done it. Reload the router.
I had to reboot as well.


Installation issues / Re: Logitech MX Air
« on: August 14, 2010, 08:32:58 pm »

What did the Keyboard cost you?

Users / Re: What devices are you running Web orbiter 2.0 on?
« on: August 09, 2010, 04:47:50 pm »

Thnx once again.... I can Kick myself.....
After all this time my weborbiter must have been working.... ;D
I installed firefox on my laptop and VIOLA!!!!! its working.  ;D

The IE7 seemed to be the problem as it is still not working...... but who cares hey... typical MS....  ;)


Users / Re: What devices are you running Web orbiter 2.0 on?
« on: August 09, 2010, 08:25:57 am »

I've removed the weborbiter again from the admin webpage. Did another apt-get update and apt-get upgrade.
Rebooted the core. Reinstalled the web orbiter as per the Wiki. Followed it step by step.

But still all I get is the flying penguin. If I hold the mouse pointer over it, a tooltip comes up "waiting for info"
Can I manually install the web orbiter?
I really want to get it working, but it seems i'm hitting a wall here....  ???

Pages: 1 ... 25 26 [27] 28 29 30