Did you do a router reload after you made the events?

Br,
Raymond

L3mce,
I am happy to help, just let me know what you want me to do and I will see what I can do.
Br,
Raymond

Hi David,

As posde once pointed out to me, make sure that the DT you want to make, is created, installed and assigned to the room where the IR-trans is (or in my case the USBUIRT) before you start learning ir-codes.
You can finish creating the DT and installing it and then, at a later time, fill in the ir-codes.

Another tip: www.remotecentral.com where you can find all sorts of ir-codes, discrete and normal once.

br,
Raymond

Congratulation to all involved!
I big thanks to all the devs who keep pushing this big amazing piece of software to the next level.
Also a big thanks to all the people who take the time to test, report bugs or help in any other way.

br,
Raymond

l3mce,

Thank you very much for all your hard work and support, making audio and video work for everybody and documenting it.

br,
Raymond

Looking very nice, i am curious on how you want to do the floor plans, media navigation and media file grids.
Makes me wanna see more
Keep up the good work.

br,
Raymond

Hi tschak909, DragonK,

i also have them on my HDD, DragonK, if for some reason you can't upload, let me know and i will try.

br,
Raymond

it turns out that when you add a light to a room with room-type 'outside area', that light gets automatically added to LMCE's auto generated sunset/sunrise events.
The light gets the on command at sunset and the off command at sunrise.

a big thanks to every one who helped, especially hari, tschak, possy and sambuca.

br,
Raymond

A big congratulation to all who are involved,

thanks for all their effort, time invested, code added and patience while giving support.

i would personally wanna thank: L3mce for his contribution, insights and user-support; Tschak for his deep knowledge, user-support and explanations; Foxi352 for doing RoamingOrb, Asterix and user-support; posde for his huge knowledge, never ending contribution to the system and user-support; Hari for his never ending additions to the device-database and user-support and Golgoj4 for his qOrbiter and user-support.

Thanks for making this such a great project.
br,
Raymond

Hari,

Thanks, i will be looking for you in IRC.

br,
Raymond

hi foogee,
Can you have LMCE 1004 send out email as a response to a event (sensor tripped, alarm breach, etc)
Because i can't seem to find it in the event pull-down menu.

Also what did you change the from into, because using a known email address gives me sometimes a email, but sometimes not?
Its a bit confusing to me...

Br,
Raymond

Hi All,

Recently i upgraded from 8.10 to 10.04.
On 8.10 i had z-wave working perfectly.
Right before going to 10.04 i added a Aeon-Labs door/window sensor which worked also perfectly.

Now on 10.04 i re-added my "respond to event" event (sunset) to control a light (this worked great under 8.10)
But now every time when the event gets fired, another light also gets turned on.
Its always the same combo.

I can turn both these lights on and of individually with a orbiter.

the zwave gear used in above case:
- Aeon-Labs zwave controller: http://wiki.linuxmce.org/index.php/Aeon_Labs_Z-Wave_Interface
- duwi inwall switch on/off
- duwi dimmer: http://wiki.linuxmce.org/index.php/Düwi_ZW_ZDAN_300_Dimmer

I also tried deleting the "respond to event" event ad re-adding it but without any luck.

In the Event Plug-in log i can see that the 2 wave-modules get a "on" command, but thats not what i specified in the "respond to event" event.

Any pointers are welcome.

Br,
Raymond

After more investigation, with big help from l3mce (thanks again), i can safely draw the conclusion that it was me who has screwed things up. What probably happened is that i ripped my cd's to the OS-Drive instead of the media drive.
LMCE doesn't delete files
I swapped my old OS-drive for a new one, so thats why they are not there anymore

Thanks for al your replies and help.

Look on the bright side: hopefully someone can learn from this, especially from the kick-ass commands from l3mce.

br,
Raymond

lspci -nn | grep -w 'VGA'

Code:

01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GT216 [GeForce GT 220] [10de:0a20] (rev a2)

apt-cache policy linux-backports-modules-alsa-$(uname -r)

Code:

linux-backports-modules-alsa-2.6.32-41-generic:
  Installed: 2.6.32-41.43
  Candidate: 2.6.32-41.43
  Version table:
 *** 2.6.32-41.43 0
        500 mirror://mirrors.ubuntu.com/mirrors.txt/ lucid-updates/main Packages
        500 mirror://mirrors.ubuntu.com/mirrors.txt/ lucid-security/main Packages
        100 /var/lib/dpkg/status

sudo aplay -l

Code:

**** List of PLAYBACK Hardware Devices ****
card 0: NVidia [HDA NVidia], device 3: NVIDIA HDMI [NVIDIA HDMI]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: NVidia [HDA NVidia], device 7: NVIDIA HDMI [NVIDIA HDMI]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: NVidia [HDA NVidia], device 8: NVIDIA HDMI [NVIDIA HDMI]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: NVidia [HDA NVidia], device 9: NVIDIA HDMI [NVIDIA HDMI]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 1: SB [HDA ATI SB], device 0: ALC888 Analog [ALC888 Analog]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 1: SB [HDA ATI SB], device 1: ALC888 Digital [ALC888 Digital]
  Subdevices: 1/1
  Subdevice #0: subdevice #0

br,
Raymond

Hi l3mce,

Your command didn't return anything on my system
I guess something else must have happened.
I am glad to hear though that LMCE CAN'T delete files on his own, i thought i might have found a bug, but i am glad i didn't.

br,
Raymond