Hello Thom,

i have try it first, the script do no detect the changer, but i think the problem is the script.
You see the system output, are is right and the scipt don´t match the changer!

lsscsi -g

[0:0:0:0]    disk          ATA                ST3808110AS              3.AA  -        /dev/sg0
[1:0:0:0]    cd/dvd     HL-DT-ST         DVD-ROM GDRH10N       0F03  -        /dev/sg1
[4:0:0:0]    disk         SAMSUNG         HD154UI                              -        /dev/sg2
[23:0:1:0]   cd/dvd    MATSHITA        DVD-RAM SW-9584        B100  -        /dev/sg3
[24:0:2:0]   mediumx      Sony           VAIOChanger1               0100  -        /dev/sg4


Marco

[When i start the Powerfile.sh manual comes this resultat:]

I have buy a Sony VAIO Living Center include the SONY DVD Changer.
The DVD-Changer is refurbished from Sony, it looks like new and work perfectly unter MCE2005.

The problem under linuxmce (8.10b2) is, the Powerfile.sh script run´s automatic, but the script don´t find the changer!


lsscsi -g

[0:0:0:0]    disk          ATA                ST3808110AS              3.AA  -        /dev/sg0
[1:0:0:0]    cd/dvd     HL-DT-ST         DVD-ROM GDRH10N       0F03  -        /dev/sg1
[4:0:0:0]    disk         SAMSUNG         HD154UI                              -        /dev/sg2
[23:0:1:0]   cd/dvd    MATSHITA        DVD-RAM SW-9584        B100  -        /dev/sg3
[24:0:2:0]   mediumx      Sony           VAIOChanger1               0100  -        /dev/sg4


When i start the Powerfile.sh manual comes this resultat:

sudo /usr/pluto/pnp/Powerfile.sh

Powerfile Detection script queue <> <> <> <> <> <> <>
type disk
cd/dvd
disk
cd/dvd
mediumx
none of the above


a look in the script:

code:

#!/bin/bash

. /usr/pluto/bin/SQL_Ops.sh
. /usr/pluto/bin/Config_Ops.sh

echo "Powerfile Detection script queue <$1> <$2> <$3> <$4> <$5> <$6> <$7>"
DevSg="$5"; DevSgEsc="${DevSg//\//\/}"

type=$(lsscsi -g|awk "/$DevSgEsc"'$/ {print $2}')
manufacturer=$(lsscsi -g|awk "/$DevSgEsc"'$/ {print $3}')
model=$(lsscsi -g|awk "/$DevSgEsc"'$/ {print $4}')

echo "type $type"
if [[ "$type" == 'mediumx' && "$manufacturer" == 'PowrFile' && "$model" == 'C200' ]]; then
        echo "it's a c200"
        /usr/pluto/bin/MessageSend dcerouter -r 0 $1 1 806 224 $2 13 "$4" 44 1737
elif [[ "$type" == 'mediumx' && "$manufacturer" == 'Sony' && "$model" == 'VAIOChanger1' ]]; then
        echo "it's a sony"
        /usr/pluto/bin/MessageSend dcerouter -r 0 $1 1 806 224 $2 13 "$4" 44 1889
else
        echo "none of the above"
        /usr/pluto/bin/MessageSend dcerouter -r 0 $1 1 806 224 $2 13 "$4" 44 0
fi

Code:

Have anybody a solution for me, what i can do?!
I don´t found in the WIKI or FORUM a install instruction about the DVD Cahnger.

Give´s a manual install procedure?

best regards,
Marco
 




 

Hello Friends,

i have try the TeVii S420 DVB-S PCI, it works fine and the channel switching it´s fast!
driver package are find: http://tevii.com/linux_tevii_ds3000.rar

You must copy the FW from Tevii to /lib/firmware and then you install the v4l from the packet (ReadMe included)
make && make install and the card work with the vdr.

--------------------------------------------------------------------------------------------------------------------
lspci | grep v

0c:07.0 Multimedia video controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
0c:07.2 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)

--------------------------------------------------------------------------------------------------------------------

dmesg | grep dvb
[   17.596194] cx88/2: cx2388x dvb driver version 0.0.7 loaded
[   17.596200] cx88/2: registering cx8802 driver, type: dvb access: shared

---------------------------------------------------------------------------------------------------------------------

Code:

lspci -vn
00:00.0 0600: 1002:5a33 (rev 01)
        Subsystem: 1734:10cc
        Flags: bus master, 66MHz, medium devsel, latency 64
        Memory at <ignored> (64-bit, non-prefetchable)
        Kernel modules: ati-agp

00:01.0 0604: 1002:5a3f
        Flags: bus master, 66MHz, medium devsel, latency 99
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=70
        I/O behind bridge: 00009000-00009fff
        Memory behind bridge: d2100000-d21fffff
        Prefetchable memory behind bridge: c0000000-cfffffff
        Capabilities: <access denied>
        Kernel modules: shpchp

00:12.0 0106: 1002:4380 (prog-if 01)
        Subsystem: 1734:10d1
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 22
        I/O ports at 8440 [size=8]
        I/O ports at 8434 [size=4]
        I/O ports at 8438 [size=8]
        I/O ports at 8430 [size=4]
        I/O ports at 8400 [size=16]
        Memory at d240a000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: <access denied>
        Kernel driver in use: ahci
        Kernel modules: ahci

00:13.0 0c03: 1002:4387 (prog-if 10)
        Subsystem: 1734:10d1
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
        Memory at d2404000 (32-bit, non-prefetchable) [size=4K]
        Kernel driver in use: ohci_hcd
        Kernel modules: ohci-hcd

00:13.1 0c03: 1002:4388 (prog-if 10)
        Subsystem: 1734:10d1
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 17
        Memory at d2405000 (32-bit, non-prefetchable) [size=4K]
        Kernel driver in use: ohci_hcd
        Kernel modules: ohci-hcd

00:13.2 0c03: 1002:4389 (prog-if 10)
        Subsystem: 1734:10d1
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 18
        Memory at d2406000 (32-bit, non-prefetchable) [size=4K]
        Kernel driver in use: ohci_hcd
        Kernel modules: ohci-hcd

00:13.3 0c03: 1002:438a (prog-if 10)
        Subsystem: 1734:10d1
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 17
        Memory at d2407000 (32-bit, non-prefetchable) [size=4K]
        Kernel driver in use: ohci_hcd
        Kernel modules: ohci-hcd

00:13.4 0c03: 1002:438b (prog-if 10)
        Subsystem: 1734:10d1
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 18
        Memory at d2408000 (32-bit, non-prefetchable) [size=4K]
        Kernel driver in use: ohci_hcd
        Kernel modules: ohci-hcd

00:13.5 0c03: 1002:4386 (prog-if 20)
        Subsystem: 1002:4386
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 19
        Memory at d240a400 (32-bit, non-prefetchable) [size=256]
        Capabilities: <access denied>
        Kernel driver in use: ehci_hcd
        Kernel modules: ehci-hcd

00:14.0 0c05: 1002:4385 (rev 13)
        Subsystem: 1734:10d1
        Flags: 66MHz, medium devsel
        I/O ports at 8410 [size=16]
        Memory at d2409000 (32-bit, non-prefetchable) [size=1K]
        Kernel driver in use: piix4_smbus
        Kernel modules: i2c-piix4

00:14.1 0101: 1002:438c (prog-if 82 [Master PriP])
        Subsystem: 1734:10d1
        Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
        I/O ports at 01f0 [size=8]
        I/O ports at 03f4 [size=1]
        I/O ports at 0170 [size=8]
        I/O ports at 0374 [size=1]
        I/O ports at 8420 [size=16]
        Capabilities: <access denied>
        Kernel driver in use: pata_atiixp
        Kernel modules: pata_atiixp

00:14.2 0403: 1002:4383
        Subsystem: 1734:10cf
        Flags: bus master, slow devsel, latency 64, IRQ 16
        Memory at d2400000 (64-bit, non-prefetchable) [size=16K]
        Capabilities: <access denied>
        Kernel driver in use: HDA Intel
        Kernel modules: snd-hda-intel

00:14.3 0601: 1002:438d
        Subsystem: 1734:10d1
        Flags: bus master, 66MHz, medium devsel, latency 0

00:14.4 0604: 1002:4384 (prog-if 01)
        Flags: bus master, 66MHz, medium devsel, latency 64
        Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=64
        I/O behind bridge: 0000a000-0000afff
        Memory behind bridge: d0000000-d20fffff

01:05.0 0300: 1002:5a61
        Subsystem: 1734:10cc
        Flags: bus master, 66MHz, medium devsel, latency 66, IRQ 10
        Memory at c0000000 (32-bit, prefetchable) [size=256M]
        I/O ports at 9000 [size=256]
        Memory at d2100000 (32-bit, non-prefetchable) [size=64K]
        [virtual] Expansion ROM at d2120000 [disabled] [size=128K]
        Capabilities: <access denied>

0c:04.0 0200: 10ec:8139 (rev 10)
        Subsystem: 1734:10b1
        Flags: bus master, medium devsel, latency 64, IRQ 23
        I/O ports at a000 [size=256]
        Memory at d2000000 (32-bit, non-prefetchable) [size=256]
        Capabilities: <access denied>
        Kernel driver in use: 8139too
        Kernel modules: 8139cp, 8139too

0c:05.0 0200: 10ec:8139 (rev 10)
        Subsystem: 1259:2503
        Flags: bus master, medium devsel, latency 64, IRQ 20
        I/O ports at a400 [size=256]
        Memory at d2000400 (32-bit, non-prefetchable) [size=256]
        Capabilities: <access denied>
        Kernel driver in use: 8139too
        Kernel modules: 8139cp, 8139too

0c:07.0 0400: 14f1:8800 (rev 05)
        Subsystem: d420:9022
        Flags: bus master, medium devsel, latency 165, IRQ 21
        Memory at d0000000 (32-bit, non-prefetchable) [size=16M]
        Capabilities: <access denied>
        Kernel driver in use: cx8800
        Kernel modules: cx8800

0c:07.2 0480: 14f1:8802 (rev 05)
        Subsystem: d420:9022
        Flags: bus master, medium devsel, latency 64, IRQ 21
        Memory at d1000000 (32-bit, non-prefetchable) [size=16M]
        Capabilities: <access denied>
        Kernel driver in use: cx88-mpeg driver manager
        Kernel modules: cx8802

Marco

Hello Klara,

in the moment i have only the core/hybrid when he works fine, then i make the md´s with diskless boot.
The MD are equal by the diskless boot, you start a new untouched PC with network PXE-boot (show in your mainboard bios),
and the core dedect the new PC (it´s need time) and build an new MD and Orbiter for this device.
When the new MD it´s ready to work, than you loged in with from another PC with SSH to the new MD.

ssh with a putty, the then go with sudo -s (root) and install your vdr equal by the core/hybrid, this is my plan, maybe it´s going easy with another method?!

Marco

PS. I have see a script "update_ diskless_MD.sh" but i hav no time to check this script what he do!!! 

Hi,

i have a Tevvi S660 DVB-S2 USB, it works with the "linux pack" from http://tevii.com/linux_tevii_ds3000.rar
You must copy the FW from Tevvi to /lib/firmware and then you install the v4l from the packet (ReadMe included)
make && make install and the box work with the vdr.  (thanks to nite_man !)

_________________________________________________________________________________________________
lsusb -v

Bus 003 Device 002: ID 9022:d660 
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x9022
  idProduct          0xd660
  bcdDevice            0.00
  iManufacturer           1 TBS-Tech
  iProduct                2 DVBS2BOX
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x80
      (Bus Powered)
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               1
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)
_______________________________________________________________________________________

dmesg | grep dvb

[   25.850980] dvb-usb: found a 'TEVII S660 DVBS2 USB2.0' in cold state, will try to load a firmware
[   25.850994] firmware: requesting dvb-usb-teviis660.fw
[   27.325924] dvb-usb: downloading firmware from file 'dvb-usb-teviis660.fw'
[   27.325937] firmware: requesting dvb-usb-teviis660.fw
[   27.636059] dvb-usb: found a 'TEVII S660 DVBS2 USB2.0' in warm state.
[   27.636215] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
[   27.765778] dvb-usb: MAC address: f76388f0
[   28.384342] dvb-usb: schedule remote query interval to 150 msecs.
[   28.384357] dvb-usb: TEVII S660 DVBS2 USB2.0 successfully initialized and connected.

________________________________________________________________________________________________

v4l2-ctl -n -d /dev/dvb/adapter0/frontend0

The program 'v4l2-ctl' is currently not installed.  You can install it by typing:
sudo apt-get install ivtv-utils
__________________________________________________________________________________________________


Marco

nite_man,

many thanks for you instruction, the vdr is playin TV javascript:void(0); !

>>>. Me and Posde try to test VDR 1.7.11 under 0810. It works but with some tricks.<<<
>>> Will add instructions to install VDR 1.7.11 later. <<<
NICE!

When you need help, let me now it, may be i can help!? testing....

Marco

My Test HTPC:
Mainboard Zotac ION 330 (Typ A); 2 x 2 GB DDR2 RAM 800Mhz; Antec Mini, DVB-S2 USB Tevii S660, 250 GB WD Green HD,

Hello to All,

i have the same problem with the VDR, the MCE run´s well, but the DVB-S/S2 with VDR makes me crazy!

Please help us and me!

Have anybody a detailed instructtion, how i can fix the VDR problem?!

Many thanks @ all from Germany.

Marco