Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - tortho

Pages: 1 2 [3]
31
Users / Re: RS232 & Sharp Aquos not working in LinuxMCE, Only Windows
« on: March 22, 2010, 08:22:13 pm »
Hi,

On the core/hybrid there is nothing in the available serial port box.

On my other MD I have "/dev/ttyS0," That one is not working either, only TestSerial..., but no autodetect

32
Users / Re: RS232 & Sharp Aquos not working in LinuxMCE, Only Windows
« on: March 22, 2010, 05:53:39 pm »
Well,

Finally the cable for the motherboard is in house and the pci RS232 card has been removed.

Still no luck.

TestSerial works and turns the tv on/off, but no autodetection in LMCE.

Any further hints?

33
Users / Re: 0810: Timed Events adding new entries by itself
« on: February 23, 2010, 11:17:39 pm »
Yes it does. and you don't need to click it twice..
It does create a new event every time you click on the link, also the first time.

This does not happen if you choose "timed events" from the top dropdown menu.

Confirmed from Google chrome.

34
Hi,

Can answer partly:

Day & Night:
Assume this is the same as sunset and sunrise which it controls by your location settings in Webadmin.
See: Wizard -> Basic Info -> Installation.

I did have an issue with a zwave device which did turn on without me telling it to do so. Discovered I had set it's location for the device to "Outside Area" (See room setup)
This device where then automatically added to a scenario and turned automatically on / off based on sunrise/sunset.

35
Users / Re: RS232 & Sharp Aquos not working in LinuxMCE, Only Windows
« on: February 23, 2010, 10:23:10 pm »
Excellent!!

Thanks a lot Hari, that worked.

Then the big question.
- Why is it not auto detected?
- Why does it not respond to com port numbers "1" or "2"...?
 and assume it will be a lot more easy to "install" the tv if it is auto detected.

36
Users / Re: RS232 & Sharp Aquos not working in LinuxMCE, Only Windows
« on: February 22, 2010, 02:52:43 pm »
Hi,

Thanks for the reply.
Nope 8N1, was a typo and does not make any difference.

Tried the bottom not on the Sharp page with minicom and no commands do work.

As additional info I can inform that I have the exactly same issue on my MD with another pc with another Sharp model LCD.
The MD does also work perfectly with my other laptop and putty under windows.

37
Users / RS232 & Sharp Aquos not working in LMCE, Only Windows
« on: February 22, 2010, 12:35:20 pm »
Hi,

On my laptop:
With windows running Putty I do control my Sharp Aquos LC52X20E with e.g. "POWR1   " & "POWR0   " or any other command from the manual.

On my Core:
Have 2 serial ports (one on the Motherboard which is not connected and one on a pci card which is connected to the TV)
Found the serial card which is connected to be /dev/ttyS1 (Port 0xdc00)
Only these 2 serial ports are reported with UART 16550A when I run setserial -g /dev/ttyS[012345678]

When issuing the below commands nothing happens:
/usr/pluto/bin/TestSerialPort -p 2 -P N81 -b 9600 -t "POWR0   \r\s500mPOWR1   \r\n" -i 1 -s "OK\r"

or

/usr/pluto/bin/TestSerialPort -p 2 -P N81 -b 9600 -t "POWR0   \r\n" -i 1 -s "OK\r"

Any suggestions on where the issue might possibly be is highly appreciated.





38
Users / Broken audio in .flv video files
« on: February 06, 2010, 10:58:50 am »
Believed that after upgrades last week playback of .flv files got broken.

Lots of noise, scratching sound on the audio and totally unusable of the video files.

Anyone else experiencing the same or have a workaround?

39
Users / Re: ACT Homepro Z-wave ZRM230 Only partially working
« on: February 03, 2010, 09:33:42 pm »
Hi,

Thanks I know it can be associated to groups, but then you need a controller to do so (Which I believe is not possible with an Aeon Z-stick which is the only other item I have in addition to switches and smoke detectors).

To have the switch show up in LMCE would as far as I can see be a huge benefit. Believe then it can be used to trigger other devices just as you do with motion detectors etc. today.

Example Event:
IF button 2 on this switch off THEN Turn off all light and stop all media.
IF button 2 on this switch on THEN turn on light from your entrance to the normally used rooms in your house...

or a lot of other scenarios If you associate you can only control the z-wave devices, not all the other functions within LMCE.

40
Users / Re: ACT Homepro Z-wave ZRM230 Only partially working
« on: February 02, 2010, 11:05:29 pm »
Hi Hari,

Thanks for the reply.
(A little confusing that you write "No", and then "You can use it to control other devices... assume this means without going through LMCE)

Then I need a different controller as I can not "associate" it with other devices with the Z-stick (As far as I know)
And then assume the association part on this page is not valid to this light switch: http://wiki.linuxmce.org/index.php/Z-Wave_Getting_Started#Setting_associations

Then to ask differently. Is there any plans to implement this in LinuxMCE?
Is this then also the "issue" with the smoke detectors?

To gain some more knowledge as youre the expert here, is this something that is launched in the new z-wave/zensys protocoll?

41
Users / ACT Homepro Z-wave ZRM230 Only partially working
« on: February 01, 2010, 12:42:06 am »
Hi,

Purchased a ACT ZRM230 light switch and was planning to use the "second" switch to turn off all my zwave devices.. but can not figure out how to get it working.

The "normal" switch works fine and is detected. Can the second one be "detected" in any way and be used in LMCE to control any of the other z-wave devices?
Using this together with Aeon Z-stick. (Assume I could have programmed it with another controller)

The device is here:
http://www.smarthus.info/redirect.php?action=url&goto=www.act-solutions.com%2FHomePro%2Fpdfs%2FHomePro%2FSpecs%2FZRM230_spec.pdf
http://www.smarthus.info/product_info.php?cPath=1_46_128&products_id=1884

Thanks!

42
Users / Re: Is there any Smoke alarm z-wave ? Or other solution as gc100 ?
« on: December 31, 2009, 10:50:28 am »
:-)

The Flexcontrol Smoke Detector = Everspring SF-812

Mine has the Flexcontrol sticker on the front and everything else refers to Everspring SF-812 which is the manufacturer.
The  siren as well is the Everspring brand.

43
Users / Re: Is there any Smoke alarm z-wave ? Or other solution as gc100 ?
« on: December 30, 2009, 12:42:26 pm »
nite_man, Believe the potentioal and possibilitites here are bigger...

Believe the following should be possible:
- Tamper alarm
- Smoke alarm
- Use it as a siren for a security alarm? Would be quite loud and awesome.
- Battery status on request
- One detector sets off all of them
- Assume the text to speach can give you a message of where the fire might be as well?


Hari:
- Is it because of a new z-wave version/revision?
It is fully working in Homeseer..
Believe you need more than one to fully test the equipment.. as they are supposed to be connected to eachother.
5 units could be associated according to the spec.... believe we could connect and set of all with LinuxMCE? Will check with some other what is possible in Homeseer..
 

44
Users / Re: Is there any Smoke alarm z-wave ? Or other solution as gc100 ?
« on: December 29, 2009, 09:53:53 pm »
Hey,
Price is not that bad. USD 100,- each for a smoke detector, wireless with battery and tamper alarm.. (Tamper alarm might be nice if you are renting out parts of your house)

I have included them in the Aeon Z-stick, but is too stupid to make a template and make it work.

Assume it would not be too much of a problem with concrete walls if you have several devices not too far away from each other... looks like good signal as I have installed a smoke detector in a small "building" next to my house as I have electricity and other stuff in there...

45
Users / Re: Is there any Smoke alarm z-wave ? Or other solution as gc100 ?
« on: December 29, 2009, 02:40:27 pm »
Hi,

Assume Hari refers to the Everspring SF-812.

It is out with all approvals etc.
I have bought 8 pcs, but can not get them to work with LMCE
Assume only some template tuning might be the needed fix.

If anyone would like to help, then please contact me.

Spec Sheet for the SF-812 can be found as a PDF on this page:
http://www.smarthus.info/product_info.php?products_id=2729

Pages: 1 2 [3]