Topics

46

Installation issues / Orbiter for Cisco 79XX issues

« on: August 10, 2010, 05:29:03 pm »

Hia,
after using the Cisco 7970 for some time, i did note some problems:
1) When receiving a call, the caller id is NOT displayed on the phones orbiters, but on MDs and Core/hybrid, it´s shown.
2) Even if the phone is registered as being in a room, it starts with living (but is registered as being on master bedroom).
3) When placing a call from one phone, trying to place a call from the other phone simply dies. Should it be a message like "all lines are busy now"?
Anyone aware of this?
TIA,
Paulo

47

Installation issues / [SOLVED] Cisco 7970 SCCP firmware update / reflash?

« on: August 07, 2010, 07:00:39 pm »

Hia,
i got a new cisco 7970G phone, and it is running in cycles (line lights) and does not stop.
I guess it is looking for firmware to load (please correct me if i'm wrong).
On my /tftpboot directory, i do have the following 7970 files:

apps70.8-5-4TH1-6.sbn
cnu70.8-5-4TH1-6.sbn
cvm70sccp.8-5-4TH1-6.sbn
dsp70.8-5-4TH1-6.sbn
jar70sccp.8-5-4TH1-6.sbn
SCCP70.8-5-4S.loads
term70.default.loads
term71.default.loads
which i assume are correct sccp files.

My syslog tells the following:

Aug  7 13:54:56 dcerouter dhcpd: DHCPREQUEST for 192.168.80.146 from 00:13:7f:fd:94:4b (SEP00137FFD944B) via eth1
Aug  7 13:54:56 dcerouter dhcpd: DHCPACK on 192.168.80.146 to 00:13:7f:fd:94:4b (SEP00137FFD944B) via eth1
Aug  7 13:55:03 dcerouter atftpd[32276]: Serving term70.default.loads to 192.168.80.146:1025

These entries repeats for hours.

So, the phone is trying to get the files.

In my SEPDefault7970.cnf.xml file i have the entry:
<loadInformation>TERM70.7-0-1-0s</loadInformation>

What else do i need to do in order ot get the phone reading the files and finally works?

TIA,

Paulo

SOLVED: i got the cmterm-7970_7971-8-5-4.zip. After searching, i did read a post where an user told not being successful with any version other than .cop. So, i got cmterm-7970_7971-8-5-4.cop, and used it's files. In 5 minutes, the phone was alive and kicking, ready for service.

P.S. Thx Hari for trying to help me on last saturday.

48

Installation issues / question about udev rules for video (webcam)

« on: August 03, 2010, 09:38:27 pm »

Hia,
due a bug on my (and anybodies M3N78-VM) concerning usb 1.1 handling, i got a startech pci board for usb, and have my usb 1.1 devices (like webcam) connected to it, leaving the mobos usb interfaces for usb 2.0 devices.
On boot, the startech pci board loads first, making the webcam getting the video0 device, which is undesireable for me.
I did create the /etc/udev/rules.d/25-name-video-devices.rules with following content:
SUBSYSTEM=="pci", BUS=="usb", SYSFS{idVendor}=="05a9", SYSFS{idProduct}=="0511", NAME="video4"
problem is: on boot, the f***g webcam gets assigned to /dev/video0.
the dmesg output for this is:
[  333.231214] ov511 7-1:1.0: Device at usb-0000:01:06.1-1 registered to video0
AFAIK, subsystem is pci and bus is usb.
Anyone with a hint?
TIA

49

Installation issues / [SOLVED] Solo USB microphone problem

« on: July 12, 2010, 07:28:16 pm »

Hia,
after some updates, Solo microphone is not working.....
When i plug it in, i get the following dmesg output:

Code: [Select]

[  307.968179] usb 3-5: new full speed USB device using ohci_hcd and address 3                                        
[  308.181442] usb 3-5: configuration #1 chosen from 1 choice                                                          
[  308.193219] input: AKM                       AK4571                    as /devices/pci0000:00/0000:00:04.0/usb3/3-5/3-5:1.3/input/input6                                                                                                  
[  308.253146] input,hidraw2: USB HID v1.10 Device [AKM                       AK4571                   ] on usb-0000:00:04.0-5                                                                                                                
[  308.491583] snd_usb_lib: disagrees about version of symbol snd_rawmidi_receive
[  308.491592] snd_usb_lib: Unknown symbol snd_rawmidi_receive
[  308.491701] snd_usb_lib: disagrees about version of symbol snd_rawmidi_transmit_empty
[  308.491702] snd_usb_lib: Unknown symbol snd_rawmidi_transmit_empty
[  308.491741] snd_usb_lib: disagrees about version of symbol snd_rawmidi_transmit
[  308.491743] snd_usb_lib: Unknown symbol snd_rawmidi_transmit
[  308.491801] snd_usb_lib: disagrees about version of symbol snd_ctl_add
[  308.491804] snd_usb_lib: Unknown symbol snd_ctl_add
[  308.491900] snd_usb_lib: disagrees about version of symbol snd_ctl_new1
[  308.491901] snd_usb_lib: Unknown symbol snd_ctl_new1
[  308.492014] snd_usb_lib: disagrees about version of symbol snd_rawmidi_transmit_ack
[  308.492015] snd_usb_lib: Unknown symbol snd_rawmidi_transmit_ack
[  308.492458] snd_usb_lib: disagrees about version of symbol snd_rawmidi_transmit_peek
[  308.492462] snd_usb_lib: Unknown symbol snd_rawmidi_transmit_peek
[  308.492531] snd_usb_lib: disagrees about version of symbol snd_ctl_notify
[  308.492532] snd_usb_lib: Unknown symbol snd_ctl_notify
[  308.492659] snd_usb_lib: disagrees about version of symbol snd_rawmidi_new
[  308.492660] snd_usb_lib: Unknown symbol snd_rawmidi_new
[  308.492700] snd_usb_lib: disagrees about version of symbol snd_rawmidi_set_ops
[  308.492701] snd_usb_lib: Unknown symbol snd_rawmidi_set_ops
[  308.516860] snd_usb_audio: Unknown symbol snd_usbmidi_create
[  308.517142] snd_usb_audio: Unknown symbol snd_usbmidi_disconnect
Any hint in how to fix it?
TIA,
Paulo

50

Users / Motion compile problem

« on: July 11, 2010, 08:03:44 pm »

Hia,
i'm trying to build the latest motion version, but with not luck.
The configure being used is:
./configure --prefix=/usr -with-ffmpeg=/opt/pluto-ffmpeg
which shows:

Code: [Select]

  *******************************
      Configure status           
      motion 3.2.12               
   *******************************

OS             :     Linux
pthread Support:     Yes 
jpeg Support:        Yes 
V4L included:        Yes 
V4L2 supported:      Yes 
FFmpeg Support:      Yes 
MYSQL Support:       Yes 
PostgreSQL Support:  No   

CFLAGS:  -g -O2 -D_REENTRANT -DHAVE_FFMPEG -I/opt/pluto-ffmpeg/include -DFFMPEG_NEW_INCLUDES -DHAVE_FFMPEG_NEW -I/usr/include/mysql -DMOTION_V4L2 -DTYPE_32BIT="int" -DHAVE_BSWAP   -march=i686                         
LIBS: -lm  -lpthread -ljpeg -L/opt/pluto-ffmpeg/lib -lavformat -lavcodec -lavutil -lm -lz -L/usr/lib -lmysqlclient -lz                                                                                                 
LDFLAGS:   -L/opt/pluto-ffmpeg/lib                                                                         

Install prefix:       /usr

and makes produces at the end:

Code: [Select]

ffmpeg.c:26:10: warning: #warning **************************************************                       
ffmpeg.c:27:10: warning: #warning Your version of FFmpeg is newer than version 0.4.8                       
ffmpeg.c:28:10: warning: #warning Newer versions of ffmpeg do not support MPEG1 with
ffmpeg.c:29:10: warning: #warning non-standard framerate. MPEG1 will be disabled for
ffmpeg.c:30:10: warning: #warning normal video output. You can still use mpeg4 and
ffmpeg.c:31:10: warning: #warning and mpeg4ms which are both better in terms of size
ffmpeg.c:32:10: warning: #warning and quality. MPEG1 is always used for timelapse.
ffmpeg.c:33:10: warning: #warning Please read the Motion Guide for more information.
ffmpeg.c:34:10: warning: #warning Note that this is not an error message!
ffmpeg.c:35:10: warning: #warning **************************************************
--------------------------------------------------------------------------------
Motion object files compiled.

Linking Motion...
--------------------------------------------------------------------------------
gcc -L/opt/pluto-ffmpeg/lib -o motion motion.o conf.o draw.o jpegutils.o video.o video2.o video_common.o netcam.o netcam_ftp.o netcam_jpeg.o netcam_wget.o track.o alg.o event.o picture.o rotate.o webhttpd.o webcam.offmpeg.o -lm  -lpthread -ljpeg -L/opt/pluto-ffmpeg/lib -lavformat -lavcodec -lavutil -lm -lz -L/usr/lib -lmysqlclient -lz
/opt/pluto-ffmpeg/lib/libavformat.a(file.o):(.data+0x0): multiple definition of `file_protocol'
ffmpeg.o:(.data+0x40): first defined here
collect2: ld returned 1 exit status
make: *** [motion] Error 1

Any hint?

TIA

51

Installation issues / Motion issues

« on: July 10, 2010, 04:10:26 pm »

Hia,
i'm trying to configure motion with a mix of cameras, usb and ip.
For ip camera, i got an ICamView USB to IP server, and using http://192.168.80.140/pda.cgi?user=viewer&password=viewer&page=image&cam=1, i can get the image from this dedicated server.
Adding this as generic ip camera (wizard -> devices -> surveillance cameras) gets template and i select generic ip camera.
For Path, i do enter: http://192.168.80.140/pda.cgi?user=viewer&password=viewer&page=image&cam=1, TCP port is 80 and IP is 192.168.80.140 and it's controlled by core.
Then i go to wizard -> interfaces -> add device, select motion wrapper, and have video input type = 8 (usb camera) and all the motion parameters for usb webcam.
What is to be changed?
Is there the need to have one motion wrapper for each cam?
The wiki is not very usefull about the configuration....
TIA

52

Installation issues / PVR-500 and input sources.

« on: July 04, 2010, 06:27:27 pm »

Hia,
i do have a PVR-500 installed with two tuners working, and i would like to plug my old VCR and/or Videocam to the RCA inputs, so i can watch or even record from them.
I could not find how to do it.
Anyone has done it and could give a hint?
TIA

53

Installation issues / [SOLVED] VideoLan-server & VideoLan-Client - still exists?

« on: July 04, 2010, 06:24:37 pm »

Hia,
form the begining of my installation, everytime orbiters are regenerated, i get failure message on staring VideoLan-server and VideoLan-Client.
Seaching the system, i never found both.
The question is: Does these two componets still exists?
On Media Directors, there is the option of disable VideoLan-CLient, but not VideoLan-Server.
TIA

54

Users / Cisco 7970 orbiter error 404

« on: July 04, 2010, 02:55:43 am »

Hia,
after today's update, when trying to access he orbiter from the cisco 7970, i get HTTP Error [404]!
The apache log tells:

Code: [Select]

192.168.80.41 - - [03/Jul/2010:21:49:17 -0300] "GET /lmce-admin/index.php?section=proxySocket&command=XML HTTP/1.1" 200 4767 "-" "Allegro-Software-WebClient/4.34"
192.168.80.41 - - [03/Jul/2010:21:49:18 -0300] "GET /pluto-admin/security_images/184_cisco.png HTTP/1.1" 404 385 "-" "Allegro-Software-WebClient/4.34
Under pluto-admin, there is no security_images directory, but under lmce-admin.
Something got broken in the last update?
TIA

55

Users / pluto-xine-player (117,136) - enable subtitle support

« on: June 29, 2010, 07:24:20 pm »

Hia,
today xine was updated, and according to the wiki, pluto-xine-player (117,136) - enable subtitle support.
How is this done?
TIA,
Paulo

56

Users / Adding a second telephone line. How?

« on: June 28, 2010, 11:26:19 pm »

Hia,
after having pstn working well, thx to the wiki (http://wiki.linuxmce.org/index.php/Sipura/Linksys_spa3000_pstn_interface), now is time to get a voip provider in order to make calling Europe much cheaper. My choice is voipcheap, but first i need to be able to add a second phone line, and next, to tune the dialplan and routing.
Questions:
1) How do i add a second phone line (could not find it in the webadmin)?
2) How to add it without the use of the ATA (which is intended only for the pstn line), but having the phone connected to it be able to route to voip?
I will call and receive calls from both (pstn and voip).
Anyone have it working and would kindly help?
TIA,
Paulo

57

Users / Headers for pluto-ffmpeg

« on: June 28, 2010, 06:57:17 pm »

Hi,
i'm trying to build the newest version of motion, but configure complains it cannot find the pluto-ffmpeg headers.
Where do i get them?
TIA,
Paulo

58

Installation issues / V4L2 drivers - OV511 problems

« on: June 26, 2010, 04:08:56 pm »

Hia,
after the last update, i'm getting some weird problems, and would like to know if someone also is having or had it:
1) core/hybrid - USB gyro mouse and gyration remote stops, and are only enabled again after a reboot.
2) core/hybrid - USB camera, after a router reload stops. Unplugging and replugging does not help.
3) without any explanation, router reload occours.
The kernel being used is the 2.6.27-17.
It seems that something might be wrong with the USB subsystem. Any hint?

EDIT: After some tests, i suspect of the OV511 driver, which seems to be causing instability problems.
Unplugging the OV511 webcam, no problems.
Plugging back the OV511 webcam, after a time, gyro mouse stops working, no more PnP detection....of any webcam...
without the camera, the router does not unexpected reload.
This problem occurs with both kernel versions i have installed: 2.6.27-13 and 2.6.27-17.

TIA,
Paulo

59

Installation issues / [SOLVED] Motion not working with USB camera

« on: June 22, 2010, 09:06:42 pm »

Hia,
today i've installed my USB camera, as described in http://wiki.linuxmce.org/index.php/Analog_cameras
After that, the camera was recognized, but i get a static image. No change, after hours.
And if i do a reload router, no more connection, even with /etc/init.d/morion restart.

The motion wrapper config is:

Code: [Select]

#image settings
frequency 0
rotate 0
width 640
height 480
framerate 15
auto_brightness off
brightness 128
contrast 128
saturation 128
hue 128

#http control
control_localhost off
control_html_output on
control_port 8888

#filters
despeckle EedDl
lightswitch 50
minimum_motion_frames 2

#detection
noise_tune on
threshold_tune on
smart_mask_speed 5
gap 5
post_capture 30
pre_capture 15

#output
locate on
text_double off
webcam_quality 80
webcam_maxrate 5
text_changes on
text_right %m-%d-%Y\n%T

#movies
ffmpeg_cap_new on
ffmpeg_timelapse 60
ffmpeg_timelapse_mode daily
ffmpeg_video_codec mpeg4

#snapshot config
snapshot_interval 60
snapshot_filename %Y/%m/%d/%H/minute_%M_%S
jpeg_filename %Y/%m/%d/%H/minute_%M_%S
movie_filename %Y/%m/%d/recordings/%m_%d_%Y_%H_%M_%S
timelapse_filename %Y/%m/%d/timelapse/%m-%d-%Y-timelapse

The device is #2 (/dev/video2) as shown in my dmesg output:

Code: [Select]

dcerouter_1008240:/home/cameras/192/2010/06/22# dmesg | grep video
[    1.188831] pci 0000:03:00.0: Boot video device
[   18.288340] Linux video capture interface: v2.00
[   18.363566] ov511 2-1:1.0: USB OV511 video device found
[   19.249711] ivtv0: Registered device video0 for encoder MPG (4096 kB)
[   19.249797] ivtv0: Registered device video32 for encoder YUV (2048 kB)
[   19.249970] ivtv0: Registered device video24 for encoder PCM (320 kB)
[   19.337928] ivtv1: Registered device video1 for encoder MPG (4096 kB)
[   19.338028] ivtv1: Registered device video33 for encoder YUV (2048 kB)
[   19.338218] ivtv1: Registered device video25 for encoder PCM (320 kB)
[   19.939129] ov511 2-1:1.0: Device at usb-0000:00:04.0-1 registered to video2

Anyone got this?
Any hints?

TIA

Paulo

60

Installation issues / Computing applications

« on: June 18, 2010, 09:51:21 pm »

Hia,
the todays update & upgrade did not restore the mythtv setup in the computing applications menu (OSD).
TIA