Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - heinola

Pages: 1 2 [3] 4
31
started over...

Zotac 8100-ce matx mobo
2gb ram 1066
gf8600 pcie ( using hdtv componetn output )
160gb sata( os drive + some media )
Fugitu sata dvdrw 
hitachi 500gb sata


DVD install beta2
(after Kubuntu + Linuxmce install had to run nvidia-config + add in
BusID "PCI:3:0:0" ( for my gf8600 )
Mode "800x600" "1024x768"

Before reboot or Linuxmce would not lauch X for its config

Setup went good  ( Love the newer Icon sets for UI + UI2 aplha )

Linuxmce detects sad1 (160gb sata in witch my os is on )

but...

sdc1 500gb hitachi is not add threw linuxmce ( ext3 format ) note also had a 320gb seagate i pluged in either sata port 3 or 4 no go either fat32 or ntfs format  -or-  ext2 " was testing id 500gb was bad ect...

the 500 and 320gb are seen in Kubuntu and can be mounted and used  as well as on my laptop via usb addapter...soo I know the physical drives are ok...

at the moment I am running apt-get update + upgrade   

i'll post if any fix cam about or more info

32
two days ago i did a dvd install of kubuntu 810

run udate + upgrade per the sites instructions 

downloaded the beta tar  ranthe commands per the site instruction.

The install took a awhile  but  i didnt notice any error.

I can run the system just fine  accually reallysmooth    but...

I have a 500gb  sata drive that has Linuxmce file structure + media on it
as well as a couple jump drives..

None of witch Linuxmce want to setup  ---but---  kubuntu sees them

I fear something went wrong during the install.    If I mount these threw Kunbunto
(Dolphin)  i can access files ect  but Linuxmce does not want to see or set them up


I have no unknown devices in Pluto admin...
fstab reads
Code: [Select]
# /etc/fstab: static file system information.
#
# <file system> <mount point>   <type>  <options>       <dump>  <pass>
proc            /proc           proc    defaults        0       0
# /dev/sda1
UUID=d8510b58-b608-48e5-a507-b6c19bf25cd3 /               ext3    relatime,errors=remount-ro,user_xattr 0       1     
# /dev/sda5
UUID=54278047-d595-4f67-9585-6c1d082a8fba none            swap    sw              0       0
/dev/scd0       /media/cdrom0   udf,iso9660 user,noauto,exec,utf8 0       0

mtab reads
Code: [Select]
rootfs / rootfs rw 0 0
none /sys sysfs rw,nosuid,nodev,noexec 0 0
none /proc proc rw,nosuid,nodev,noexec 0 0
udev /dev tmpfs rw,mode=755 0 0
fusectl /sys/fs/fuse/connections fusectl rw 0 0
/dev/disk/by-uuid/d8510b58-b608-48e5-a507-b6c19bf25cd3 / ext3 rw,relatime,errors=remount-ro,user_xattr,data=ordered 0 0
/dev/disk/by-uuid/d8510b58-b608-48e5-a507-b6c19bf25cd3 /dev/.static/dev ext3 ro,errors=remount-ro,user_xattr,data=ordered 0 0
tmpfs /lib/init/rw tmpfs rw,nosuid,mode=755 0 0
varrun /var/run tmpfs rw,nosuid,mode=755 0 0
varlock /var/lock tmpfs rw,nosuid,nodev,noexec 0 0
tmpfs /lib/modules/2.6.27-16-generic/volatile tmpfs rw,mode=755 0 0
tmpfs /dev/shm tmpfs rw,nosuid,nodev 0 0
devpts /dev/pts devpts rw,nosuid,noexec,gid=5,mode=620 0 0
securityfs /sys/kernel/security securityfs rw 0 0
nfsd /proc/fs/nfsd nfsd rw 0 0
automount(pid8070) /mnt/device autofs rw,fd=4,pgrp=8070,timeout=30,minproto=2,maxproto=4,indirect 0 0

i think its be mounted by something else but df-h reads
Code: [Select]
linuxmce@dcerouter:~$ df -h
Filesystem            Size  Used Avail Use% Mounted on
rootfs                142G  9.2G  125G   7% /
udev                 1012M  2.8M 1010M   1% /dev
/dev/disk/by-uuid/d8510b58-b608-48e5-a507-b6c19bf25cd3
                      142G  9.2G  125G   7% /
/dev/disk/by-uuid/d8510b58-b608-48e5-a507-b6c19bf25cd3
                      142G  9.2G  125G   7% /dev/.static/dev
tmpfs                1012M     0 1012M   0% /lib/init/rw
varrun               1012M  360K 1012M   1% /var/run
varlock              1012M     0 1012M   0% /var/lock
tmpfs                1012M  2.2M 1010M   1% /lib/modules/2.6.27-16-generic/volatile
tmpfs                1012M     0 1012M   0% /dev/shm
linuxmce@dcerouter:~$

any ideas would be helpfull

33
Users / Acer AX1200-U1711A Desktop
« on: October 28, 2009, 05:23:57 am »
any try these as a hybreed or a md?

34
Users / Re: Aspire R3600 REVO 250G/2G RAM Mini Desktop PC
« on: August 15, 2009, 05:24:45 pm »
I see it has a net boot issue but all info would be helpfull  :)

35
Users / Aspire R3600 REVO 250G/2G RAM Mini Desktop PC
« on: August 15, 2009, 05:22:40 pm »
Any try this as a MD as of yet ?

OS : Linux 
CPU: Intel Atom N230 (1.6 GHz)
Chipset: NVIDIA ION Chipset
Support full HD 1920x1080
DIMM: DDR2 800 SO-DIMM 2 GB
HDD: 250 GB
Video out: HDMI port x1 / D-SUB VGA port x1
Card Reader: SD/SDHC/MS/MS Pro/MMC
WiFi: IEEE 802.11 b/g/n
LAN:10/100/1000 Base-TX Ethernet LAN on Board 
Dia.182  x 36  x 218  mm
COLOR :Blue 
Weight : 750g
 

36
Users / Re: md usb webcam setup?
« on: August 09, 2009, 06:00:57 pm »

Both my webcams that know worked on core..

Both of them have status lights on allthe time from MD bootup..  even before i set up motion

37
Users / Re: energy usage interface?
« on: August 08, 2009, 08:06:41 pm »
looking into it

38
Users / md usb webcam setup?
« on: August 08, 2009, 08:06:16 pm »
Setup:

AMD x2  32bit hybreed  (masterbedroom)
AMD 64bit md (livingroom)

I have a current wifi ip camera  Panasonic BB-HCM371A

auto detected and set up  pan/tilt function ok  but no zoom  ( working on this )
also have it on motion wrapper via CORE

I have a Logitech webcam that worked on the CORE using motion wrapper.

I moved it to the livingroom md

I got no prompt for new device when I did this...

My question is what is the next step as far as trouble shooting this issue  -or- someone has doc on this kind of setup/issue

ty

39
Users / energy usage interface?
« on: August 07, 2009, 02:11:42 pm »
Any know of any interfaces that are linux compat for RDC ( residential demand control )
or shedding/trimming power usage in a said structure to a preset limit...

Most of them just use a simple induction coil on both phases to monitor incoming usage -or- outgoing in the case of alt energy equiped homes.

Since Linuxmce already has the structure to shed loads eg: zwave insteon ect.

If not this might be a usefull/needed function in the future...

Im sure a gc-100 unit could be used in this function...

Or i might get a STAMP kit and make start playing with my own interface  lol

any info at all is cool


Heinola 

40
Users / Re: control a/v equipment via usb/ir + x10 commands ?
« on: August 01, 2009, 09:49:16 pm »
I got a couple questions...

(1) Can the UIRT at a md control other md's via those md's UIRT...like in a house wide media command..?
      ( wanted to play a music playlist from all md's) 

(2) On the GC-100 is there a way to tie the gc-100 into a IR network to control md's from the gc unit?



I am so used to having a house hold ir network  hard to get away from the old ways  lol



41
Users / Re: control a/v equipment via usb/ir + x10 commands ?
« on: June 21, 2009, 06:31:25 pm »
Thanks guys,  I got a bit of reading in and both methods look like they would work.

The gc-100 method looks like something I will try when I get the funds for that setup.
As well if I move I will have a better area for a core only setup in the ultility room....
.....plz let me move  LOL


But...for now I will get a couple usb transceivers for my hybrid and Md's

As for the the home stereo system I might run a cheap old puter that will netboot
just to run that threw a usb transceiver..

Ill let you all know how it goes for me  :)

I am so ready for bluetooth / headset support  :)

42
Users / Re: control a/v equipment via usb/ir + x10 commands ?
« on: June 21, 2009, 06:00:16 pm »
ty for the input,  will read into it  :)

43
Users / Re: control a/v equipment via usb/ir + x10 commands ?
« on: June 15, 2009, 07:51:55 pm »
some of the general home audio equipment might not have a md near it 

just wondering if I have to do it that way

44
Users / Re: control a/v equipment via usb/ir + x10 commands ?
« on: June 15, 2009, 05:24:11 am »
maby this

http://www.insteon.net/2411t-IRLinc-Transmitter.html

there used to be a x10-3012 type converter but i can only find the europe version

45
Users / control a/v equipment via usb/ir + x10 commands ?
« on: June 15, 2009, 04:54:58 am »
I base setup is

core//masterbed// 2.1ghz amd x2 2gb 160sata 32" sharp 720p
md//livingroom// 2ghz amd 64 1gb (diskless)
orbit//livingroom// old desktop on xp

looking at a ipaq wifi hx2400 for a master control for house..
.....at least for masterbed for the future

I wanted to setup for 5.1 sound (RCA) in masterbed
&
5.1 sound (RCA) livingroom

I wanted to control the A/V equipment via  IR  threw X10 knowing that some of
the equipment will have simular codes i do not want to relay commands to
one reciever or tv and in turn affecting a reciever/tv that i do not to control at the time.

I was thinking of (2) usb/IR transcievers one for the core and md or md's (for controling that rooms equipment as well as otherrooms

Something that would translate IR to X10 commands  (mini controller x10 maby -or Powermids)

(my thought on the later is if I get a home audio stereo like a Sony STG-197 i could control threw x10)
>Power toggle
>volume
>input (prob a input feed from a MD or the core)
>am/fm
>a/b zone

If any have tried and failed or had success in what I hope to try to do make a post

Thank you










Pages: 1 2 [3] 4