Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - stallione

Pages: [1] 2 3 4
Users / Asterisk outbound SIP routing 10.04
« on: October 25, 2014, 07:38:03 pm »
I am finally upgrading my system to 10.04 and am confused about how to route to different SIP trunks
I have two trunks, one is for international calls only. So I need to add a route for any calls initiated with 011* to pick a particular sip trunk.
How would I do that now that we no longer use FreePBX? (I am assuming we have to modify the db?) Any guidance would be much appreciated.

Users / Re: TSCHAK has a TSCHAKlet now.
« on: July 23, 2013, 01:01:11 am »
Congrats Thom!!!

Users / Re: MP4 Crash
« on: March 13, 2013, 11:52:19 am »
I am still running 810, and this has been a problem from day 1 for me.
What I do is before the file finishes, I hit the skip button to start the next video. Xine freezes only when it is done reading a file and has to read the next file in the list.

Users / Re: Thom, Our Thoughts are with you...
« on: March 31, 2012, 12:38:22 am »
Thom, my prayers go out for your Father and to provide you strength at this hour of the test you are going through.

Developers / Re: LinuxMCE Game Player - Game Recording
« on: December 16, 2011, 08:51:06 pm »
Thom, you are truly insane!!!
Awesome job!!

Users / Re: How to setuo sccp.conf and use SCCP under Asterisk
« on: December 16, 2011, 08:48:11 pm »
I think he was asking about a door-bell camera, or a camera tied to the doorbell to see who is at the door. :)

Users / Re: Too many thermostat/temperature notifications
« on: September 22, 2011, 03:38:46 pm »
Hi Hari,
Yes, zwave template. Is there a way to cut down on the temp change notifications?
 It looks like the following

07      09/22/11 8:37:06.575            Event #25 has no handlers <0x745eab90>
01      09/22/11 8:37:06.575            Climate_Plugin: EVENT_Temperature_Changed_CONST ! <0x745eab90>
07      09/22/11 8:37:06.575            Received Message from 257 (Standard Thermostat / Family Room) to -1001 (unknown / ), type 2 id 25 Event:Temperature Changed, retry none, parameters: <0x745eab90>
07      09/22/11 8:37:06.575              Parameter 30(Value): 25.00 <0x745eab90>
07      09/22/11 8:37:37.459            Event #25 has no handlers <0x745eab90>
01      09/22/11 8:37:37.459            Climate_Plugin: EVENT_Temperature_Changed_CONST ! <0x745eab90>
07      09/22/11 8:37:37.459            Received Message from 257 (Standard Thermostat / Family Room) to -1001 (unknown / ), type 2 id 25 Event:Temperature Changed, retry none, parameters: <0x745eab90>
07      09/22/11 8:37:37.459              Parameter 30(Value): 25.00 <0x745eab90>

Users / Too many thermostat/temperature notifications
« on: September 10, 2011, 05:17:50 pm »
Is there a way to reduce the number of "Temperature Changed" message being logged to Dcerouter.log? It seems like every 30 seconds the Standard Thermostat logs an entry even without a change in temperature.
Any ideas to reduce the verbosity of the logs?

Users / Re: DCERouter Delay function
« on: July 17, 2011, 04:00:30 pm »
Hi Nuwis,
I have a similar scenario setup to turn off the lighs in my mudroom after 5 minutes which gets triggered by a sensor during night time hours. Attached you can see the screenshot. I am running 810. This has worked flawlessly for me for the past year or so. Something to keep in mind is that when you setup things in LMCE especially lighting and other 'Scenarios', I have noticed that after you reload your router, go ahead and reboot it else you get erratic results with triggered events.

Users / Wayne Dalton Zwave Thermostat +1 / -1
« on: July 15, 2011, 06:21:53 pm »
I was wondering if it is just my setup that doesn't work when I send a +1 or -1 temp adjustment to the thermostat. I am able to successfully send out specific numbers to the thermostat but not the incremental values. ideas?

Users / Thermostat Schedule
« on: May 23, 2011, 12:51:56 am »
I have an Intermatic (similar to the wayne-dalton) zwave thermostat as part of my LMCE install but I don't see how to add it to the Thermostat Scheduler. If there is a wiki out there, please point me to it or let me know what to do and I'll add a new wiki entry.

I have two X10 controllers and a zwave controller in my setup, no problems. (CM11, CM15 and Zwave USB)

Users / Turning off monitor when sending 'Halt MD'
« on: September 19, 2010, 02:25:14 pm »
When we click on 'Halt MD' button, is it possible to send a monitor/TV off command before we start with the MD shutdown/suspend process automatically?

Hi Paulo,
Would you please tell me which are the files that you have in your tftp folder for the phone so to load the firmware? (I am running an older version and would like to know what I need to do to get it to 8-5-4TH1-6) I downloaded the files from Cisco's web site along with the cop file. Do you have to rename the .cop file and how about the xml files, did you point it to the new software?

Users / Re: Jerky HD Video on Asus AT3N7A-I
« on: August 10, 2010, 03:16:33 am »
the file extension is m2ts

Pages: [1] 2 3 4