29
« on: September 12, 2008, 02:51:07 am »
I pressed and held the button on the PLM and the led stayed on solid. I also used and extension cord connected on the same circuit and I get the same result:
(***):Current Command:0
(***):SndIns:Queue:18
(***):out:02 6B 40 Length:3
(***):receive timeout=1
05 09/11/08 20:36:51.036 GSDMessageTranslator isCmdImplemented = false <0x42003950>
05 09/11/08 20:36:51.038 #### Pre-Process Queue = 1 <0x42003950>
05 09/11/08 20:36:51.041 _QueueProc Pre - 193 : 0 <0x40800950>
05 09/11/08 20:36:51.041 GSD-Sleep Pre 193 : 0 <0x40800950>
05 09/11/08 20:36:51.041 Process Queue = 1 <0x40800950>
(***):------dce--- cmdID:193, cmdFrom:0, cmdTo:41, cmdType:1, Priority:1
(***):------dce--- X10 DEVICE!!!
(***):DeviceID=A2
(***):X10 Byte1:6E
(***):X-----------SndIns: Waiting for response to:SetCfg
(***):X-----------SndIns: Current Queue Length:20
(***):From:41
(***):current State:100
(***):Wanted State:0
(***):ReportStatus: device:41 Status:0
05 09/11/08 20:36:51.188 GSDMessageTranslator isCmdImplemented = false <0x42003950>
05 09/11/08 20:36:51.189 #### Pre-Process Queue = 1 <0x42003950>
05 09/11/08 20:36:51.189 GSD-Sleep Post 193 : 0 <0x40800950>
05 09/11/08 20:36:51.189 _QueueProc Post - 193 : 0 <0x40800950>
05 09/11/08 20:36:51.189 _QueueProc Pre - 193 : 0 <0x40800950>
05 09/11/08 20:36:51.189 GSD-Sleep Pre 193 : 0 <0x40800950>
05 09/11/08 20:36:51.190 Process Queue = 1 <0x40800950>
(***):------dce--- cmdID:193, cmdFrom:41, cmdTo:41, cmdType:1, Priority:1
(***):Detected Command sent to Self!
05 09/11/08 20:36:51.193 GSD-Sleep Post 193 : 0 <0x40800950>
05 09/11/08 20:36:51.193 _QueueProc Post - 193 : 0 <0x40800950>
(***):receive timeout=2
(***):receive timeout=1
(***):receive timeout=2
(***):receive timeout=3
(***):Command Stalled! resetting and retrying
(***):Current Command:0
(***):SndIns:Queue:20
(***):out:02 6B 40 Length:3
(***):receive timeout=1
(***):receive timeout=2
(***):receive timeout=3
(***):Command Stalled! resetting and retrying
Did everyone follow this step in the setup instructions?
Adding a Code Group
* Click 'Edit Ruby Codes' ( loads Edit Ruby Codes Popup)
* In the field to the LEFT of 'Create new group', type in 'Insteon PLM'
* click 'Create new group'
b4 is broken have to run sql manually to add new group close 'Edit Ruby codes' page. Look at 'Edit Device Template' popup page and note Device_Category and Manufacturer you will need to set them in sql code below
INSERT INTO InfraredGroup (FK_DeviceCategory,FK_Manufacturer,Description,FK_CommMethod,psc_id,psc_batch,psc_user,psc_frozen,psc_mod,psc_restrict) VALUES (Device_Category,Manufacturer,"Insteon PLM",2,NULL,NULL,NULL,NULL,NULL,NULL);
run this sql and reload 'Edit Ruby codes' page and you should see 'Insteon PLM' in 'Uses Group/Codeset'
* If the 'Uses Group/Codeset' does not change to 'Insteon PLM', repeat the previous 2 steps again.
* Once the 'Uses Group/Codeset' says 'Insteon PLM' Check 'Discoverable Interfaces'
* Check 'Ruby Internal Commands'
* click Update
When I did this:
* In the field to the LEFT of 'Create new group', type in 'Insteon PLM'
* click 'Create new group
The 'Uses Group/Codeset' said 'Insteon PLM' and I didn't edit the sql. Is this ok?
Thanks