Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - maverick0815

Pages: 1 ... 33 34 [35] 36 37 ... 43
Users / Re: need some help with the phonebook
« on: January 15, 2010, 09:43:58 pm »
Friends, I really can't make heads or tails of it....
just suppose I will delete my phonebook again as well as the trunk I created...start fresh:
the international accesscode for germany is 0049
a local areacode is for example 0375
the phonenumer is 1234567
If I want to call that number from where I am it would be: 03751234567
if it was a international call it would be 00493751234567
Suppose I would stick with automatic configuration, the field "When dialing a local number, automatically prepend the area code" will contain what..0049 or 0375, or only 375?
or what? The next line to prepend one digit would be "0" for Europe.
So, assuming I did those about the phonebook then? So far what I did was putting 49 for coutry code, 375 for areacode and 1234567 for the phonenumber, however in dial as it always appeared like this  : 9011493751234567- and of course that doesn't dial...and like I said above- incoming calls do not get reported in the phones correctly. If I check this in the reportpanel in freepbx I at least the the number like this :03751234567, but the number being shown is something else.
I know there are lots of people with different problems...but this is driving me nuts...

Users / Re: need some help with the phonebook
« on: January 14, 2010, 10:36:41 pm »
I finally fillled my phonebook, but I'm experiencing some problem still. Whenever a call is coming in, I always get one and the same caller id from the phonebook reported. Did any of you guys experience that too?

Installation issues / Re: latest update- no more TV
« on: January 09, 2010, 10:03:43 pm »
there was no provider found for my location, so I had to use mythtv-setup.
there was a new xmltv entry as LMCE-default. I had some manual configuration to do, like changeging the videosource for the channels, but I could not watch anything. I deleted everything and tried a fresh start. I still had to connect the lnb and link the videosource. then I tried the channel-scan and got matter what I tried, rebooting after card-detection, or only quick reload...I can neither watch nor tune nor scan...I also cannot go back to before. Like I said, I checked the firmware I used and recompiled v4l...but I can still not find any channel.
I am open to any suggestion.

Installation issues / latest update- no more TV
« on: January 09, 2010, 08:22:16 pm »
I did a dist-upgrade this evening, rebooted and was then notified, that I had a Wintv nova hd s2 connected to the dcerouter and was asked if I wanted to use it.
Since this is my card and I was intrigued, that the templates have been released, I said yes.....ever since I am trying to get my TV back to work. After some trying around, I finally caved in and deleted all my settings in mythtv, rebooted and started anew. After I confirmed the use of the card, I went to mythtv-setup, but there I got a nasty surprise, since I cannot tune anymore! The channelscan breezes through with all timeouts and no new channel found! Right new I am trying to get my old settings back...I deleted the card info in the webadmin, deleted everything from mythtv, put the firmware again and complie v4l once more...I just hope this will work, otherwise I'm stuck without TV this weekend

Installation issues / Re: 810 Doesn't recognize discs
« on: January 08, 2010, 06:36:43 pm »
I had a similar issue...check if libdvdcss is installed.

Users / Re: need some help with the phonebook
« on: January 07, 2010, 09:04:30 pm »
the more I play around with the telecom-features, there questions I have....
for example: how can I access the general voicemail other than by going to the webadmin? What format is the recording there? When I opened it the first time, firefox complained about a missing plugin, ie8 came up with the brilliant idea of getting quicktime(yuck) to do the job. If I click the download link it downloads it as wave, but mediaplayer doesn't want to play it.

Users / Re: need some help with the phonebook
« on: January 07, 2010, 07:21:02 pm »
hmm...I still couldn't figure out where those digits come from, but I also have another question: is there any softphone for windows known to be able to access the phonebook? So far that would be quite cool. Right now I have x-lite running on my windows-pc, but I would change it for something else if I could use any other, if it had this feature. I'm also looking for some cordless IP-phones...and if those would be able to get the phonebook too, it would be the coolest thing. Right now I'd just be happy for the right softphone.

Users / Re: DVB Cards info needed for Templates
« on: January 05, 2010, 07:39:34 pm »
I got a hauppauge nova hd s2

here are my two cents:
lspci -vn:

v4l2-ctl -n
   Input   : 0
   Name    : DVB
   Type    : 0x00000002
   Audioset: 0x00000000
   Tuner   : 0x00000000
   Standard: 0x00000000007F7FF7 ( PAL NTSC SECAM )
   Status  : 0

Users / need some help with the phonebook
« on: January 05, 2010, 07:26:34 pm »
I have slight problem with the phonebook entries. I live in Germany and have a phonenumber like this : 0049 371 1234567
However when I start putting the country code in the first field, what appears in the "dial as" is this: 90110049
I don't understand what causes the 9011 to appear. I checked in the trunk for the dial pattern, but this is still as I set it: X.
Since I finally managed to get the asterisk to talk to my fritzbox via sip, I would really like to start filling in the phonebook.

Installation issues / Re: mythtv player isn't installed on MD
« on: January 02, 2010, 12:31:46 pm »
go to the webadmin interface there go to wizard->devices->mediadirectors.
Scroll down to your MD in question and look for Softwaremodules, there is a button next to it, that says edit.
it opens another window, see if  mythtv is checked, then save and close.

Installation issues / Re: asterisk
« on: December 20, 2009, 11:56:46 pm »
Well, Thom, I suspected you'd say that...and I wish I could too
so far, when I use the automatic configuration, select broadvoice and then put in the login-data for the fritzbox, it creates two lines- none of which I could delete from this page.
If I go to manual configuration, I find one trunk named broadvoice and a user context named fritzbox.
I also tried the intercom calling from one md to another or to the softphone- it gets dropped because there is no route.
Other than that I find those messages in the status page:
Could not reload the FOP operator panel server using the script. Configuration changes may not be reflected in the panel display.
Added 7 minutes ago
retrieve_conf failed to sym link the /etc/asterisk/sip.conf file from modules
Retrieve conf failed to copy file(s) from a module's agi-bin dir: copy(/usr/share/asterisk/agi-bin/list-item-remove.php): failed to open stream: Permission denied
copy(/usr/share/asterisk/agi-bin/directory): failed to open stream: Permission denied
copy(/usr/share/asterisk/agi-bin/dialparties.agi): failed to open stream: Permission denied
copy(/usr/share/asterisk/agi-bin/recordingcheck): failed to open stream: Permission denied
copy(/usr/share/asterisk/agi-bin/fixlocalprefix): failed to open stream: Permission denied
copy(/usr/share/asterisk/agi-bin/enumlookup.agi): failed to open stream: Permission denied
copy(/usr/share/asterisk/agi-bin/checksound.agi): failed to open stream: Permission denied

Installation issues / Re: asterisk
« on: December 20, 2009, 01:53:09 pm »
I'm still having some trouble getting along with asterisk
I found that the only script working for setting up a sip-trunk is broadvoice. I tried copying the script and modify it, so that it will configure asterisk to work together with my fritzbox- but that doesn't work- nothing registers. If I use the originial broadvoice-script and put in the logindata for the fritzbox, its working so far, that I suddenly have to lines  showing with the data- one for fritzbox, one for broadvoice. Then, whenever I want to make a call- either inbound or outbound- I get a recorded message, that the number I have called is not in use. I have no idea what to do. For testing purposes I  installed x-lite softphone on my computer and with the help of the wiki I set it up, so that it successfully registers with linuxmce, but I still cannot make even one call with it.
Any suggestions, anybody?

exactly the same here!

Installation issues / Re: HVR-4000
« on: December 11, 2009, 07:54:17 am »
just to make sure: when you try to configure mythtv, are you using the orbiter or are you trying from KDE-desktop? I'm asking, because obviously there are some people, who try to configure mythtv from kde-desktop, while actually you should go to Computing in your orbiter and start mythtv setup from there. if your tv-card is loaded properly, then you should have no problems tuning with mythtv, unless another application hijacked the card already

Installation issues / Re: vdpau on ion330
« on: December 09, 2009, 07:24:13 am »
regarding videoplayback I am experiencing an instability issue besides mkv-files. I don't know if this is perhaps related to the nvidia-drivers or the vdpau-libraries. Like last night- I was watching some TV and then wanted to watch a few episodes of my favourite series. The first file played fine, the second behaved just like I described with the mkv-files. I had to reboot the MD twice before it would eventually play the file.

Pages: 1 ... 33 34 [35] 36 37 ... 43