Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Esperanto

Pages: 1 ... 9 10 [11] 12 13 ... 19
Users / Re: Need some dedicated testers.
« on: January 25, 2014, 07:58:58 pm »
Still the same.

Also the Audio list crashes. More songs than movies so that makes sense.

Users / Re: Need some dedicated testers.
« on: January 25, 2014, 03:41:31 pm »
thx posde. It's Missing instead of IsMissing I saw:

mysql> select count(*)  from File where EK_MediaType=5 and IsDirectory = 0 and Missing = 0 ;
| count(*) |
|     2018 |
1 row in set (0.00 sec)

Users / Re: Need some dedicated testers.
« on: January 25, 2014, 02:35:40 pm »
I think I have more. Here getting the list has always crashed.

Anybody knows the correct query to show the number of movies?

mysql> select count(*)  from File where EK_MediaType=5 and IsDirectory = '0';
| count(*) |
|     2019 |
1 row in set (0.08 sec)

Users / Re: Need some dedicated testers.
« on: January 25, 2014, 09:35:57 am »
Do you have a lot of videos?

As you can see in a few post ago I have the same issue and I indeed have quite some entries.

Users / Re: Need some dedicated testers.
« on: January 22, 2014, 08:18:15 pm »
I just tried the latest build (#103) on Nexus7 2013. When I press video it starts loading and then gives me: Unfortunately, qOrbiterQt4 has stopped.

Users / Re: lightpack with discount
« on: December 31, 2013, 01:48:51 pm »
think it expires today

Users / lightpack with discount
« on: December 27, 2013, 07:58:59 pm »
Lightpack now in preorder with discount ($99 total).

use couponcode:


Users / Re: No sound on cisco 7970
« on: November 29, 2013, 04:33:01 pm »
I have a 7970 that works without sound problems using SCCP.

Check on your firewall (Advanced -> Network -> Firewall rules) that you have a rule that allows incoming RTP (sound) packets:

Protocol: udp
IP version: both
Source port: 10000 to 20000
Type: core_input

Thanks but it did not make a difference. Since I already was able to receive sound using the orbiter on the core/hybrid I am not sure if this made any difference in any case.

Anything else you can think of that might cause this? I am a bit confused since there is not much to configure. The cisco is pnp, the sip provider is straightforward and the core is directly connected to the internet. hmmmm.

Users / Re: No sound on cisco 7970
« on: November 27, 2013, 08:00:29 pm »

I hoped telecom was fully functional. I have a basic setup with one SIP provider and one phone connected. Calling on the core (directly connected to the internet) works properly. Only the incomming audio on the cisco is lacking.

any suggestion appreciated.

Users / No sound on cisco 7970
« on: November 25, 2013, 08:06:28 pm »

I just connected a Cisco 7970 (using sccp) to my setup but the incomming sound is not working. Anyone knows what might be the issue.

Maybe interesting for others: I also had an issue with connecting to my sip provider which gave me the message  'The Number You have Dialed is not In Service' when caling the number. I seemed what caused it was that reverse DNS did not resolve to the hostname. Specifying the IP address in the host field solved that.

Users / Re: Low energy MCE configuration?
« on: October 06, 2013, 08:03:27 pm »
I have not experienced a environment friendly spirit here yet. A bigger setup often uses more power. However I think that if you chose your components properly you don't need a laptop. At least if you also need some performance (otherwise there might be other options, I saw some links to software that runs on routers instead). If you need performance I think you can create a pretty efficient core. Take a look here . There must be many more similar sites that give good info.

Good luck and keep us updated.

Users / Re: Kickstarter Campaign to fund a programmer?
« on: September 29, 2013, 01:34:51 pm »
- How much work would it be to get totally rid of Pluto and have lmce GPLed or is that still lightyears away?


Users / Re: Kickstarter Campaign to fund a programmer?
« on: September 19, 2013, 09:50:33 am »
...but speaking on behalf of the cheapskates; how would contributing towards LMCE compare to paying out for a dianemo license?

I think the main thing is that dianemo already have a 12.04 release out with latest mythtv etc. Also people expect support when they pay and continuity. When it is clear what people will get I think they are willing to pay. Personally I don't want to pay for a dianemo license and would prefer to pay to the open source variant.....

Users / Re: Mele F10
« on: September 11, 2013, 08:30:28 pm »
here ya go:

Code: [Select]
<esperegu> any guru on mapping/configuring remotes? I want to define a specific button on a remote and have the xev output but cannot seem to figure out what to put into the template.
<esperegu> I tried media,85,D in the template but that does not seem to do anything
<TSCHAKMac> after adding this, you need to be sure, to reload the router. Is the scan code indeed 85 ?
<esperegu> TSCHAKMac: part of the output of xev when I press the button is in
<esperegu> TSCHAKMac: it is the middle mouse button (button 2) and key 85
<esperegu> TSCHAKMac: I also tried a mapping like: 4,2=2,176
<esperegu> 5,2=3,176
<TSCHAKMac> uh, no
<TSCHAKMac> you'll need to get more data in this case
<TSCHAKMac> comment out #loglevels in the media director's /etc/pluto.conf
<TSCHAKMac> then killall -9 OrbiterGL
<TSCHAKMac> and grep -rin "GenericHID" /var/log/pluto/XX_name_of_your_launchorbiter.log
<TSCHAKMac> you'll see a scan code when you press the button, hopefully
<TSCHAKMac> use that value.
<esperegu> TSCHAKMac: k. thx. awesome. will do that.
<TSCHAKMac> be sure to uncomment the LogLevels line again, and killall -9 OrbiterGL after all of this, so you don't needlessly log things when you're done.
<esperegu> TSCHAKMac: does not seem to give a code there
<TSCHAKMac> hm ok
<TSCHAKMac> then some code will have to be added to deal with it.
<esperegu> TSCHAKMac: :-(. that easy to do in the template or is that hardcore coding?
<TSCHAKMac> no, it won't be able to be handled in the template
<TSCHAKMac> you'd need to modify Orbiter itself
<esperegu> :-(. outofmyleague ;-)
<esperegu> TSCHAKMac: any chance/way I can supply you with the right info so you could add it one day you are working on the specific part in the code anyway?
<TSCHAKMac> no, it doesn't work that way, unfortunately.
<TSCHAKMac> esperegu: whatdevice is it?
<esperegu> TSCHAKMac: I got an rf03 on ebay:
<esperegu> TSCHAKMac: I also created a template for it but that does not have all the buttons:
<esperegu> TSCHAKMac: is there info somewhere with guidelines on which actions are preferred for buttons on a remote?
<esperegu> TSCHAKMac: (I mean which are the actions best to put behind the buttons in lMCE)
<TSCHAKMac> no, there isn't. The point was to map stuff to what made best sense for the remote at hand on a case by case basis.

Users / Re: Kickstarter Campaign to fund a programmer?
« on: September 10, 2013, 02:51:22 pm »
Let's face it: The people who are using LinuxMCE these days are mainly cheapskates. They use it cause it is free as in beer. Some are here, cause they think they can make a quick buck out of it for clients.

hence my suggestion to attract more people willing to spend some money on the software.

Regarding the current users: how many active installs are there? Is that visible in the statistics somewhere?

Pages: 1 ... 9 10 [11] 12 13 ... 19