Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Esperanto

Pages: 1 [2] 3 4
16
Users / Remote (gyration) not repeating commands
« on: March 27, 2014, 10:11:05 am »
I have a gyration 3101 remote which gets detected by the GO Cordless GC1005M #1812 template. According to its configuration string it need to repeat the volume up and down keys when they are being pressed:
Code: [Select]
voldn,122,R
VolUp,123,R
However while the orbiter receives a lot of key presses DCE router and so the general serial device that should use it do not, they only receive 2 of them and then stop while the orbiter still receives them. Anyone knows why this might be the case?

tail -f /var/log/pluto/21_LaunchOrbiter.sh.log | grep "GenericHIDInterface"
Code: [Select]
01      03/27/14 10:01:56.614           GenericHIDInterface::DecodeEventInFD() Successful read of 48 bytes from fd 18 <0xb09ffb40>
01      03/27/14 10:01:56.846           GenericHIDInterface::DecodeEventInFD() Successful read of 48 bytes from fd 18 <0xb09ffb40>
01      03/27/14 10:01:57.742           GenericHIDInterface::DecodeEventInFD() Successful read of 48 bytes from fd 18 <0xb09ffb40>
01      03/27/14 10:01:57.993           GenericHIDInterface::DecodeEventInFD() Successful read of 32 bytes from fd 18 <0xb09ffb40>
01      03/27/14 10:01:58.029           GenericHIDInterface::DecodeEventInFD() Successful read of 32 bytes from fd 18 <0xb09ffb40>
01      03/27/14 10:01:58.065           GenericHIDInterface::DecodeEventInFD() Successful read of 32 bytes from fd 18 <0xb09ffb40>
01      03/27/14 10:01:58.101           GenericHIDInterface::DecodeEventInFD() Successful read of 32 bytes from fd 18 <0xb09ffb40>
01      03/27/14 10:01:58.137           GenericHIDInterface::DecodeEventInFD() Successful read of 32 bytes from fd 18 <0xb09ffb40>
01      03/27/14 10:01:58.173           GenericHIDInterface::DecodeEventInFD() Successful read of 32 bytes from fd 18 <0xb09ffb40>
01      03/27/14 10:01:58.182           GenericHIDInterface::DecodeEventInFD() Successful read of 48 bytes from fd 18 <0xb09ffb40>
tail -f /var/log/pluto/DCERouter.log
Code: [Select]
08      03/27/14 10:01:56.616           Received Message from 21 (OnScreen Orbiter / Living Room) to 10 (Media Plug-in / Living Room), type 1 id 90 Command:Vol Down, retry none, parameters: <0x5ebf7b40>
08      03/27/14 10:01:56.617           Received Message from 21 (OnScreen Orbiter / Living Room) to 20 (The core/hybrid / Living Room), type 1 id 90 Command:Vol Down, retry none, parameters: <0x9bda0b40>
08      03/27/14 10:01:56.617           Forwarding 90 Command:Vol Down up pipe to 98 (AVC-A1SRA (RS232)) <0xb61f8b40>
05      03/27/14 10:01:56.618           The target device 20 (routed to 20) has not registered. <0xb61f8b40>
08      03/27/14 10:01:57.743           Received Message from 21 (OnScreen Orbiter / Living Room) to 10 (Media Plug-in / Living Room), type 1 id 90 Command:Vol Down, retry none, parameters: <0x5ebf7b40>
08      03/27/14 10:01:57.745           Received Message from 21 (OnScreen Orbiter / Living Room) to 20 (The core/hybrid / Living Room), type 1 id 90 Command:Vol Down, retry none, parameters: <0x9bda0b40>
08      03/27/14 10:01:57.745           Forwarding 90 Command:Vol Down up pipe to 98 (AVC-A1SRA (RS232)) <0xb61f8b40>
05      03/27/14 10:01:57.745           The target device 20 (routed to 20) has not registered. <0xb61f8b40>
tail -f /var/log/pluto/98_Generic_Serial_Device.log
Code: [Select]
05      03/27/14 10:01:56.618           GSDMessageTranslator isCmdImplemented = true <0xb54ffb40>
05      03/27/14 10:01:56.618           #### Pre-Process Queue = 1 <0xb54ffb40>
05      03/27/14 10:01:56.660           _QueueProc Pre - 90 : 0 <0xb6e3eb40>
05      03/27/14 10:01:56.660           GSD-Sleep Pre 90 : 0 <0xb6e3eb40>
05      03/27/14 10:01:56.660           Process Queue = 1 <0xb6e3eb40>
05      03/27/14 10:01:56.660           Parameter:  <0xb4affb40>
05      03/27/14 10:01:56.680           GSD-Sleep Post 90 : 0 <0xb6e3eb40>
05      03/27/14 10:01:56.680           _QueueProc Post - 90 : 0 <0xb6e3eb40>
05      03/27/14 10:01:57.745           GSDMessageTranslator isCmdImplemented = true <0xb54ffb40>
05      03/27/14 10:01:57.745           #### Pre-Process Queue = 1 <0xb54ffb40>
05      03/27/14 10:01:57.782           _QueueProc Pre - 90 : 0 <0xb6e3eb40>
05      03/27/14 10:01:57.782           GSD-Sleep Pre 90 : 0 <0xb6e3eb40>
05      03/27/14 10:01:57.782           Process Queue = 1 <0xb6e3eb40>
05      03/27/14 10:01:57.782           Parameter:  <0xb4affb40>
05      03/27/14 10:01:57.804           GSD-Sleep Post 90 : 0 <0xb6e3eb40>
05      03/27/14 10:01:57.804           _QueueProc Post - 90 : 0 <0xb6e3eb40>


17
Users / Where to debug squeezeslave not starting?
« on: March 24, 2014, 09:51:58 am »
I added a squeezeslave device on 'Wizard | A/V Equipment', put it in a room, set the 'Alsa Output Device', gave it a MAC, updated it and reloaded the router. It added as device 105. The process does not appear to be running. I get no loggin in the file:
Code: [Select]
# ls -lia /var/log/pluto/105*
ls: cannot access /var/log/pluto/105*: No such file or directory

I tried adding some extra logging as described in http://wiki.linuxmce.org/index.php/Logging_levels to /etc/pluto.conf (currently am on LogLevels = 1,5,7,8,10,13,22,29,30,34 ) and reloaded the router but I am not sure which ones are appropriate. Slim log (/var/log/pluto/58_Slim_Server_Streamer.log) saids it is creating the device and it is an unknown type. Any suggestions?

Code: [Select]
========== NEW LOG SECTION ==========
1       03/24/14 09:39:03       58 (spawning-device)    Starting... 1
1       03/24/14 09:39:03       58 (spawning-device)    Found /usr/pluto/bin/Slim_Server_Streamer
10      03/24/14 9:39:03.165            Device: 58 starting.  Connecting to: localhost <0xb6ff2700>
10      03/24/14 9:39:03.177            Setting timeout for socket 4 to 20 <0xb6ff2700>
10      03/24/14 9:39:03.222            Requesthandler 0x85b1800 (device: 58) runThread now running <0xb65ffb40>
10      03/24/14 9:39:03.260            App_Server started <0xb6ff2700>
05      03/24/14 9:39:03.260            Trying to connect to SlimServer at address: 127.0.0.1:9090 <0xb6ff2700>
10      03/24/14 9:39:03.260            We have made a successful connection to the slim server on 127.0.0.1:9090. Life is good. <0xb6ff2700>
10      03/24/14 9:39:03.260            Connect OK <0xb6ff2700>
05      03/24/14 9:39:03.260            Creating child 105 <0xb6ff2700>
10      03/24/14 9:39:03.260            Got CreateEvent for unknown type 2148. <0xb6ff2700>
05      03/24/14 9:39:03.260            Note: Device manager has attached a device of type 2148 that this has no custom event handler for.  It will not fire events. <0xb6ff2700>
10      03/24/14 9:39:03.260            Got CreateCommand for unknown type 2148. <0xb6ff2700>
05      03/24/14 9:39:03.260            Note: Device manager has attached a device of type 2148 that this has no custom handler for.  This is normal for IR. <0xb6ff2700>

18
Users / Possy: ? about joggler
« on: March 22, 2014, 04:16:38 pm »
Possy: since you use a lot of jogglers I have a few questions I hope you are willing to answer:
- whats your current opinion on them?
- they the best fixed orbiter atm?
- If not what is a better option?
- Do they have a pnp experience already?

thx a lot.

19
Users / Weird audio/video pipes / rs232 behaviour
« on: March 20, 2014, 09:24:12 am »
I have a LG TV that is connected to my hybrid via rs232. My amp is also connected to the hybrid, both via a dual rs232 usb adapter.

My Amp was detected immediately and added properly and is functioning as expected. The LG was not detected initially (due to upper/lowercase in the detection script) and I managed to adapt it so that that also get detected. Now the weird stuff ;-).

When I plug in the adapter it finds my TV, asks me how it is connected (I specify the port and that it is connected via the amp and on which port and the n the amp) and then it does a restart. Then it mentions again that it found the device and goes to the steps again. There are no pipes made by lmce. I talked to tschalk and he said just add them manually which I did. Then it worked. However this morning the pipes where gone again (had a few reloads because I added an orbiter). So I wanted to add them via Wizard | A/V Equipment but when I press 'Edit Audio/Video Pipes' and then with 'Connected to Media Director' select 'The core/hybrid' I get no ports I can select. I removed the device and replugged the serial usb adapter. The tv got found twice again but still no pipes. So I decided to try the Connection Wizard where I can nicely draw the line to the device but after updating it does not appear in the list in 'Wizard | A/V Equipment'

wtf is going on???

20
Users / Audio amp suggestions requested
« on: March 19, 2014, 04:36:42 pm »
I got squeezelite running on my nas and would like to be able to actually hear what is playing ;-). Anybody has suggestions for a cost effective way too amplify the sound? I have power in the area and can also us the usb port with a bit longer cable. I do however want the amp to be somehow turned of when its not in use to save some power there.

all suggestions are welcome.

thx

21
Users / Zone2 implementation of receiver
« on: March 19, 2014, 04:34:00 pm »
Is there a preferred way of implementing a zone2 on a receiver when that is used for squeezelite/squeezeslave? I would like to be able to control the volume and turn the amp on and off for squeezelite.

22
Users / rs232 generic serial high load avgs
« on: March 19, 2014, 10:03:37 am »
When I plug in my usb dual serial device I get insane high load averages after a while. ( load average: 20.61, 17.68, 12.47 ).

Anybody can give me a direction on where to debug that?

23
Installation issues / LG rs232 script
« on: March 18, 2014, 01:15:34 pm »
When I connect my LG TV via rs232 the detection script does not find it. When I run the command manually I get:

Code: [Select]
# ./20_LG_TV.sh 1 2 /dev/ttyUSB1
LG TV detection script queue 2
A 01 OK01x\r\n
A 01 OK01x\r\n
It's not a LG TV

However the connection works fine as when I do:
Code: [Select]
# /usr/pluto/bin/TestSerialPort -p /dev/ttyUSB1 -P N81 -b 9600 -t "ka 01 00\r\n" -s "a 01 OK" -i 2
A 01 OK00x\r\n

it turns off and with
Code: [Select]
# /usr/pluto/bin/TestSerialPort -p /dev/ttyUSB1 -P N81 -b 9600 -t "ka 01 01\r\n" -s "a 01 OK" -i 2
A 01 OK01x\r\n

it goes on again.

This is the content of the script:
Code: [Select]
#!/bin/bash
echo "LG TV detection script queue $2"
# make sure its on
/usr/pluto/bin/TestSerialPort -p $3 -P N81 -b 9600 -t "ka 01 01\r\n" -s "a 01 OK" -i 2
# double check that its on
/usr/pluto/bin/TestSerialPort -p $3 -P N81 -b 9600 -t "ka 01 FF\r\n" -s "a 01 OK" -i 2

if [[ "$?" -ne 0 ]]; then
echo "It's not a LG TV"
#/usr/pluto/bin/MessageSend dcerouter -r 0 $1 1 806 224 $2 13 "$4" 44 0
exit
fi
echo "test"
# older TVs should not have a "xb" command
/usr/pluto/bin/TestSerialPort -p $3 -P N81 -b 9600 -t "xb 01 FF\r\n" -s "b 01 OK" -i 2
if [[ "$?" -eq 0 ]]; then
echo "LG TV with newer command set"
#/usr/pluto/bin/MessageSend dcerouter -r 0 $1 1 806 224 $2 13 "$4" 44 2126
exit
fi
# double check that it responds correctly to the older command
/usr/pluto/bin/TestSerialPort -p $3 -P N81 -b 9600 -t "kb 01 FF\r\n" -s "b 01 OK" -i 2
if [[ "$?" -eq 0 ]]; then
echo "LG TV with older command set"
#/usr/pluto/bin/MessageSend dcerouter -r 0 $1 1 806 224 $2 13 "$4" 44 1915
fi

Anyone sees what needs to be changed? thx

24
Users / 12.04 black screen
« on: March 15, 2014, 01:57:37 pm »
On my MD I often get a black screen. I can still press F7 to show the menu but the content that was showing is not visible anymore. Any suggestions?

25
Users / clean /usr/pluto/deb-cache
« on: March 15, 2014, 12:50:49 pm »
How can I clean the deb-cache? I removed a ppa but it still got the entries in pluto's deb-cache.

26
Users / pulseaudio on core/MD
« on: March 14, 2014, 02:45:05 pm »
Anyone experience with running pulseaudio on the core or MD's?

27
Users / squeeze player on freebsd nas
« on: March 14, 2014, 09:18:14 am »
For anyone interested in running squeezelite / squeezeslave on your freenas. binary attached. (requires portaudio: pkg_add -r portaudio)

28
Users / Mele F10 still best RF remote?
« on: March 10, 2014, 08:40:36 am »
Is the Mele F10 still the best current RF remote for lmce or is there better value available?

29
Developers / 1204 install broke my internet connection
« on: March 03, 2014, 02:18:34 pm »
I think being able to control the interfaces a bit during installation is nice (swap&test). At least the installation broke my internet and I was disconnected from the ISP and unable to recover so I got stuck without internet and thus life :-) (Linuxmce was probably sending offers over the internet which killed my internet connection). I suppose we need something that controls (and swaps) the interfaces during installation if required. During installation it said no internet (while that was plugged in since it is was the machine that was running lmce). Swapping interfaces on the network page automatically rebooted the core but the harm was already done.

Also there was no warning to remove the usb stick. (I did not remove it and then the reboot got stuck).

I also saw that the patch for 10.04 regarding the local host in the nameserver list is not implemented yet.

30
Users / sound alert
« on: February 11, 2014, 02:37:45 pm »
How can I send a message with sendmessage to play a sound alert without interrupting the current state of the MD/orbiter (it can stop playing as long as it continues afterwards)


thx!

Pages: 1 [2] 3 4