Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ladekribs

Pages: 1 [2] 3 4 ... 6
16
Installation issues / Re: Problem with installing updates
« on: March 18, 2011, 08:01:02 pm »
Installing from behind a proxy is not easy, I have tried a couple of times, but always failed.

even if you have the proxy settings for http and ftp other scripts might not know the way out, as of what I know.


BR Stefan

17
Users / Re: Can I control a DLNA device (SONY TV) from Linuxmce?
« on: February 01, 2011, 02:39:35 pm »
Hi All,

Sony support said that for time being such commands (poweron/off) are not supported, but has now been suggested as a good feature.




BR Stefan

18
Users / Re: Pictures on NAS drive not appearing in LinuxMCE Picture menu
« on: February 01, 2011, 02:33:27 pm »
hi maxinva,

how did you copy the to the NAS?

if you use the samba share, permissions usually works.


BR Stefan

19
Users / Re: Problems with create_amp_*.pl
« on: January 23, 2011, 11:53:43 am »
@Daniel yes so was mine, and that resultet in the "The number you have dialed is not in service"
so I removed it and now it works
i am using digisip, now converted to bredband2

BR Stefan

20
Users / Re: Problems with create_amp_*.pl
« on: January 22, 2011, 08:05:52 pm »
if I go to advanced - configuration - phones setup inbound routes, and clear the DID number then inbound calls works

we should not change the settings in freepbx manually so is there som other way to change the DID settings?


BR Stefan

21
OK I thought there where minor differences between them only

22
It was from here:

V8.12 Download available at: http://radiotwenterand.nl/~graver/cisco/SIP-7960/P0S3-8-12-00.zip

wrong version?


BR Stefan

23
Hi I tried putting the firmware in tftpboot i downloaded from http://www.voip-info.org/wiki/view/Asterisk+phone+cisco+79xx (and renamed to sxp#mac#) but got same result.

24
Users / Re: Can I control a DLNA device (SONY TV) from Linuxmce?
« on: January 20, 2011, 08:49:55 am »
Thank You all, I will start reading.

25
Users / Re: Can I control a DLNA device (SONY TV) from Linuxmce?
« on: January 19, 2011, 07:00:16 pm »

@Thom,I have been searching for a while with no luck, trying to read the upnp docs, but know too little to understand it

@Posde, thought that maybe some other device used standard UPNP or DLNA commands, like for example the roku soundbridge,or the Sony VPL-HS51 Ethernet?


BR Stefan

26
Users / Can I control a DLNA device (SONY TV) from Linuxmce?
« on: January 19, 2011, 01:56:58 pm »
I would like to power on/off a Sony TV via the network using DLNA commands, and maybe also select input,control volume etc.

Is it possible?
where can I find the command syntax?


BR Stefan

27
Users / Re: Problems with create_amp_*.pl
« on: January 14, 2011, 09:09:04 am »
@Aviator, thank you for the tip I will compare them

also curious to see Pointman87s working settings

BR Stefan

28
Have been trying some time to get the 7965 configured, but it keeps rebooting and says uppgrading and then a fast error flash.

when I look in the /tftpboot 2 files are created SIPDefault.cnf and SIP#mac#.cnf
I used the Cisco 7960 template, also tried the 7970 orbiter but then no files gets created in /tftpboot

from where should it load it software?

any suggestions how to get further?


BR Stefan

29
Installation issues / Re: LG LCD Template
« on: January 11, 2011, 05:43:53 pm »
Hi Barney

Yes the digital tuner works I have not programmed the tv with the channels in the right order, bute selecting either analog or digital works.


BR Stefan

30
Users / Re: Problems with create_amp_*.pl
« on: January 10, 2011, 10:59:14 am »
Hi,

I used Broadcom template to create a digisp file but I also get the message "The number you have dialed is not in service. Please check the number and try again" when calling in.
maybe I should try the sipgate template?

I can dial out ok just need to dial 9 before the phonenumber.

BR Stefan

Pages: 1 [2] 3 4 ... 6