Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ladekribs

Pages: [1] 2 3 ... 6
1
Users / Re: LinuxMCE suddenly rings
« on: Today at 10:07:24 am »
same thing happened to me as far as I can see.
I had an extension used by a Siemens gigaset phone with password "12345" when I changed that password, the ringing stopped. so if I not total misunderstood, asterisk is open for communication to the extensions if you know the password and ID.

BR Stefan

2
Users / Re: LinuxMCE suddenly rings
« on: November 21, 2014, 07:36:51 am »
Do you have an extension with a very simple password, that might have been hacked?

BR Stefan

3
Users / Re: Automatic adding Internet Radio streams to LinuxMCE
« on: November 18, 2013, 08:17:09 am »
It worked for me also, no problems either. Nice!

BR Stefan

4
Posde , but how? This is a new installation LinuxMCE newer saw the disk before.
would it be listed under devices then?

BR Stefan

5
I think I have the same problem as Jamo had.

I had an old 1004 20120508033925950 installation with a 500GB Sata disk partioned into / 100GB Swap 5Gb and rest for a data partition, the root user (or what it is called) was "linuxmce", filled up the disk with data and could use it well.

Later I bought a solid state disk, removed the old 500 GB disk, and installed again from the DVD, user this timed was "lmce".
a few weeks later I installed the and repartioned the 500 GB using gparted to only hold one data partition.
Booted up LinuxMCE, but LinuxMCE did not see the disk even after many(10 maybe) reboots and reloads, so I fired up X on the Headless installation, and there from dolphin I can see the disk, and when I try to access it I am being asked for a password and if I enter correct password for user "lmce" (note both user have different password) I can access the disk, but LinuxMCE still does not see it.

can this be same issue?

BR Stefan

6
Users / Re: 1004: The time has come.
« on: June 13, 2012, 12:43:33 pm »
Hi,

Question, I get "hum" over HDMI sometimes after stopping music or video, feels like a software problem.

anyone else have the same experience?



BR Stefan

7
Installation issues / Re: Dianemo issue with USB Webcam
« on: May 25, 2012, 08:36:11 am »
Yes POSDE I will be quiet for a while now

8
Installation issues / Re: Dianemo issue with USB Webcam
« on: May 24, 2012, 09:12:33 am »
Oh I am sorry it should have been "cat /dev/video*" and it should give something like /dev/video0

BR Stefan

9
Installation issues / Re: Dianemo issue with USB Webcam
« on: May 23, 2012, 08:38:00 am »
I am no expert, but I am trying to understand webcam under 1004.

what does cat /dev/videox say?


BR Stefan

10
Installation issues / Re: Some calls are being made
« on: February 17, 2012, 12:08:39 pm »
Hi Brononi,

I now very little about SIP but there is a common pattern in the Dst in row 7 & 8
0001520173882639
xx00020173882639

can that be some one trying to dial with different area or coutry codes?

do you recognize the IP adress in row 9 & 10 178.11...

BR Stefan

11
Users / Re: UVC video cameras - Motion question
« on: January 10, 2012, 02:35:26 pm »
Motion has a streaming functionality where you can open a browser to 192.168.80.1:8000 (increase 1 for each camera)
this feature  is enabled in Linuxmce(0810).

check the motion config files and also site lavrsen.dk/foswiki/bin/view/Motion/WebHome

/etc/motion/thread0.conf will show setting

BR Stefan

12
Users / Re: Temperature display in orbiter?
« on: November 19, 2011, 08:28:20 pm »
I am not correct person to answer but remember seeing this:
http://forum.linuxmce.org/index.php/topic,11328.75.html

BR Stefan

13
Users / Re: Generic IP Device - Configure
« on: November 10, 2011, 09:39:55 pm »
Thank you Claudio i will see if I understand.

Best Regards Stefan

14
Users / Re: Generic IP Device - Configure
« on: November 09, 2011, 06:49:34 pm »
Hi ,

I am a bit confused over how to compile the http request, I am comparing with the Panasonic IP Camera but I am not sure of how the 192.168.1.201/forms.htm?led1=1
would fit in.

please advice me.


thanks Stefan

15
Users / Re: Has my sigate UK account been hijacked because of LMCE?
« on: September 29, 2011, 12:02:57 am »
Fibres,

loggs found at Web admin - Advanced - configuration - Phones setup - (FreePBX) - Reports

Pages: [1] 2 3 ... 6