Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - pga57

Pages: 1 ... 6 7 [8] 9 10
106
Users / Re: Shoutcast Plugin
« on: July 27, 2009, 06:14:16 pm »
Humm... I have now the genres displayed on the webdt but still nothing on the N810. :-(
Very strange.

Best regards,
Philippe

107
Users / Re: Shoutcast Plugin
« on: July 24, 2009, 02:03:17 pm »
Hello Sambuca,

Is there a reason why the station genre are note displayed on an (external) orbiter ?
I try it on a N810 and a Webdt366 and it give me nothing when I select the shoutcast option (UI1)
It work with the orbiter from the PC media director.

Philippe


108
Users / Re: New Z-Wave driver
« on: June 09, 2009, 06:54:41 pm »
The StatusReport command works, but ZWave worked again this after-noon without intervention.
I thought the reset would be automatic with this new driver.
I did not translate correctly your exchanges.

Thank you for these details

Philippe

109
Users / Re: New Z-Wave driver
« on: June 09, 2009, 07:24:57 am »
Hello Hari,

For me, the lastest ZWave driver (ZWave-0710-32bit-20090605.bz2) don't resolve the error I have    
after a few days of proper functioning.
The Seluxit viaSENS Homecontroller give me the same problem I have with my previous Tricklestar 300ZW-EU-W and ZWave-0.0.2-0710-32bit.bz2 driver.

36   06/09/09 7:12:43.254      ERROR: ZW_SEND could not be delivered to Z-Wave stack <0xb792fb90>
36   06/09/09 7:12:46.353      No callback received: await_callback: 141 timer: 31 <0xb792fb90>
36   06/09/09 7:12:46.353      ERROR: Dropping command, no callback received after three resends <0xb792fb90>
36   06/09/09 7:13:16.461      We have been idle for 30 seconds, polling device states <0xb792fb90>

Do I set all associations    again?

Philippe

110
Users / Re: New Z-Wave driver
« on: June 07, 2009, 09:03:17 pm »
Hi Philippe,

It is not a tar archive. All you need is to bunzip it (command is bunzip2 if I remember correctly).

Good luck,
Mark

[/quote]

Hi Mark,
I thought there was a problem because the input file did not have the same name as the previous version (ZWave-0710-32bit-20090605 instead ZWave).
So, I've use bunzip2 and have install this new version on my core.
I'll see if that corrects the problems that I described
previously (April 15)

Thank's for your help !
Philippe


111
Users / Re: New Z-Wave driver
« on: June 07, 2009, 07:18:50 pm »
http://vt100.at/files/ZWave-0710-32bit-20090605.bz2

br, Hari

Hello Hari,

I have those errors when extracting the archive:

linuxmce@dcerouter:~$ sudo tar jxvf ZWave-0710-32bit-20090605.bz2
tar: This does not look like a tar archive
tar: Skipping to next header
tar: Error exit delayed from previous errors

I have made a lot of downloads with the same result :-(
Is the file ok on your side ?

Philippe

112
Users / Re: Setting up Siemens Gigaset IP
« on: May 22, 2009, 05:38:41 pm »
It's ok !
I can now consult my voicemail with the gigaset S675IP.
I had to check "RFC 2833" in the advanced phone parameters.

Philippe

 

113
Users / Re: Setting up Siemens Gigaset IP
« on: May 22, 2009, 03:29:23 pm »
Hi,

I've just finished to setup my gigaset S675IP phone with mce710.
It work but I can't access to my voicemail.
When asterisk ask me for the mailbox number and password it does not recognize them.
I've not this problem with the cisco 7970.
Is there something to be done to resolve this ?


Thank's
Philippe

114
Users / Re: New Z-Wave driver
« on: April 17, 2009, 08:43:44 am »
Strange...this morning my shutters were reopened without changing my config and I can control my lights again.
It appears that the system work after a while.
The Zwave log seems ok.

Philippe


115
Users / Re: New Z-Wave driver
« on: April 16, 2009, 06:59:02 am »
My remote controleur is a Tricklestar 200ZW-EU-W and the stick is a Tricklestar 300ZW-EU-W.
I use the SIS mode I've find in the Zwave wiki.
It worked for about 1 month (with 1 shutter only) without problem.

I think like you that the stick has a defect.
I've order another one (Seluxit now) to verify

Best regards,
Philippe


116
Users / Re: New Z-Wave driver
« on: April 15, 2009, 09:30:05 pm »
I use:
3 x Merten Blind control (580699) + Radio shutter push-button (504519)
2 x HomePro ZRP230 (plug-in appliance)
2 x HomePro ZDP230 (plug-in lamp module)

They all stop working.
It is like the zwave stick does not work anymore.

I had the same problem and re-installed all (driver etc..) after a delete but prefer now search the cause of the problem.

Philippe

117
Users / Re: New Z-Wave driver
« on: April 15, 2009, 09:03:04 pm »
Hello Hari,

Yesterday we discuss (on irc) a problem I had with my zwave setup.
After correction of my setup, the network worked again.
But this evening I does not work anymore, without changing anything :-(.
I've just configurate last evening some timed events to open and close my 3 electric stores.
I've post my zwave log at http://pastebin.com/m192ed64a

Can you look at it and explain me what's append ?
The error begin at 08:37:48.

Thank's,
Philippe

118
Paypal contribution sent.

Philippe

119
Count with my contribution too!

Philippe

120
Users / Re: Cisco 7970 and Asterisk config help
« on: March 22, 2009, 09:34:58 am »
I've resolve my external calls problem.
My outbound route was not correct.

I have allways the "bad request protocol packet" error in the asterisk log.

What can be the reason ?

Philippe
 

Pages: 1 ... 6 7 [8] 9 10