Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - zug

Pages: 1 2 3 [4]
46
Installation issues / automount failures
« on: April 01, 2008, 09:22:34 am »
In the syslog I get a couple of these messages every second. Does anybody know what is causing these? I have looked in the fstab but there seems to be nothing there. I think 41 is a harddrive that has since been removed from the core.

Apr  1 08:19:03 dcerouter automount[16497]: failed to mount /mnt/device/41
Apr  1 08:19:03 dcerouter automount[16528]: lookup(program): lookup for 41 failed


Thanks,
Mark

47
Installation issues / Re: PXE booting
« on: March 31, 2008, 06:54:34 pm »
I have got a little bit further now, I have only one card but it seems to get the IP ok but then says unable to connect to router. Restarting in 5 seconds.
Are there any logs anywhere to find out whats going on?

48
Installation issues / Re: PXE booting
« on: March 31, 2008, 10:34:40 am »
well yes I do but the 2nd nic is not plugged in. I think I have tried it with just one though. I will try again.

49
Installation issues / PXE booting
« on: March 30, 2008, 12:24:43 pm »
My md boots into the pxelinux kernel, then as it loads it runs dhclient and gets the Ip address but seems to hang there. Then about two minutes later it will output the dhcp reply over and over again. I can go no further and have to restart. Has anybody experienced this before? Is there any logs saved when pxebooting?
Thanks,
Mark

50
Users / Re: Abit An-M2HD Motherboard
« on: March 28, 2008, 07:31:51 pm »
I was looking into it but I couldn't find any drivers to output HDMI audio :(

51
Users / Re: 2x pvr-500 but only one to watch OR recording
« on: March 24, 2008, 08:18:01 pm »
How have you set them up? does it show 4 tuners when you setup mythtv? ie video0,1,2,3 ? I think you have to set the channels up on each tuner. What inputs are you using on the cards? ie s-video etc.

Side note, how are you finding the picture? I have the same card but have white lines going across the screen :(. It looks really bad

52
Users / Re: "Cannot connect to router"
« on: March 20, 2008, 09:44:28 pm »
anybody ? :(

53
Users / Re: "Cannot connect to router"
« on: March 19, 2008, 08:56:49 pm »
I have a standard 1 nic core with an 192.168.80.0/24 and a 192.168.1.0/24(adsl router) interface. I am simply connecting a pxe booted MD to it but it tells me it cannot connect to router.
Also I have noticed I do not have a diskless folder. Is this still used? I have run the setup diskless MD script and it seemed successful but this folder does not seem to be where it should be?

54
Users / Re: "Cannot connect to router"
« on: March 18, 2008, 08:53:34 pm »
This is crazy I have not done anything unordinary but it just wont work. Can nobody help me? :(
I have installed the Windows XP orbiter which works but it cant play video. This is just too hard :(

55
I am probably not the best person to answer this but my understanding is the two ethernet entries you have should be on different IP addresses ideally on different ranges. Do you have an internet connection for this network because the whole point of the two network interfaces on the one network card is so they run on different subnets and your Core becomes the router for the mds and orbitors.
Therefore your eth0 should run on your Internet network subnet ie 192.168.0.X and the gateway should be your DSL router or Cable router etc. The eth0:0 should be for the internal Linuxmce network such as your orbitors and mds. The default subnet is 192.168.80.X. This interface should not have a gateway because it IS the gateway for the linuxmce subnet. This should also be the DNS server for your network so the domain-name-server option should point to the core's IP on the linuxmce subnet.

The next-server is an option used for PXE booting. When the client boots to LAN the next-server tells the client which IP address to boot from. Therefore this should also be the core's IP on hte linuxmce subnet.


Thinking about it, you may not need to have separate subnets running, but it is just how I do it. You could probably have eth0 and eth0:0 on the same subnet :ie 192.168.0.X but definitely not having the same IP address.


I may be completely wrong but that is my understanding. Hope it helps.

56
Users / Re: "Cannot connect to router"
« on: March 17, 2008, 11:14:45 pm »
Can anybody help me please? I just want an MD but it is so so so difficult.
I have tried PXE booting but I get "cannot connect to router" and reboots over and over. I have tried installing from the linuxmce dvd but it complains that the screen resolution is wrong and is stuck in a loop. I have tried pxe booting a laptop but that seems to hang on the mouse module loading. Can anybody please please help it's driving me insane, how can it be so hard to install an MD :( Does anybody have a full step by step guide to creating an MD without PXE booting?

57
Users / Re: "Cannot connect to router"
« on: March 17, 2008, 09:39:18 am »
no I disabled the DHCP on my adsl router. I have even tried installing from the dvd on the MD and then connecting to core but it just seems to be stuck in a loop of " Your resolution has changed" and tries to recreate the UI over and over.

58
Users / Re: Attn: all AN-M2HD owners
« on: March 17, 2008, 09:37:11 am »
My install went fine with this board and didn't need to upgrade any drivers. However this may help for the graphics drivers:
http://forum.linuxmce.org/index.php?topic=3368.0

59
Users / "Cannot connect to router"
« on: March 15, 2008, 09:15:00 am »
Hi,
I have a core working but whenever I try to pxe boot a MD i get an error saying "Cannot connect to router" and it then restarts 5 seconds later. Does anybody know how to fix this? I have tried two different PCs and get the same problem so I think its a problem with the core.
Thanks,
Mark

60
Users / PXE boot freezes
« on: February 27, 2008, 12:26:15 pm »
Hi,
I am trying to network boot my laptop but the kernel seems to hang on the following line :

PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12

Has anybody experienced this before? I have disabled legacy USB support in the bios but it still fails (read this could be the cause from another forum)

Can anybody help ?
Thanks

Pages: 1 2 3 [4]