Is there a changelog for the last couple of updates.

I think something bad has happened to my mythtv server component,  in that my xbmc/openelc front ends can no longer show live tv or recorded tv.

Any way to roll back to test?

 

I'm running Dianemo S rather than Linuxmce,  so maybe the panels are different,  see my attached screenshot for maybe some clues - see that for user (and password) there are dedicated configuration input fields, and I don't put the full server address/path.

Do you get an image if you pop the address of your camera into a normal web browser:

http://camerauseridhere:camerapasswordhere@192.168.178.181/axis-cgi/jpg/image.cgi

where 192.168.... is your camera IP address

Any advice at all appreciated, have tried everything I can think of, reset/recreated my z-wave network, checked wiring, tried another new Dimmer module, and exhausted google.

and set config param is the screen shot above,  that appears incorrect.

Looks like a Dianemo oddity,  if Linuxmce is the same as the wiki screenshots.

Thanks for your suggestion to exclude device from network, and include it again.  It didn't fix this issue, but noticed when excluded that the wall switch works fine - see my new thread.

With z-wave Fibaro FGD-211 dimmer module,  *not* included in z-wave network.  The light switch, 1 press to switch on, 1 press to switch light off, hold switch to set dimmer level - works fine/as expected.

As soon as I include the z-wave module in my Linuxmce/Dianemo z-wave network,  the light switch can no longer be used to turn light off.It does switch light on and can set dimmer level.  

Control from Linuxmce orbiters works as expected, allowing off/on/level.

Exclude it from z-wave network again, and switch works fine, allowing to switch off the light.

Any ideas/things to check?

Thanks Hari,  I'm struggling to find where you are directing me.

I choose :

Wizard / Devices / Interfaces

Click on Advanced for the Zwave interface

Shows me my ZWave device ( Template #1754 )

Click on Send command to device

I now have a drop down list with the options:

Add Node
Assign Return Route
Download Configuration
Remove Node
Report Child Devices
Reset
Send Command to Child
Set Association
Set Config Parameter
Set Polling State
SetWakeUp
Status Report

Following the wiki I get to the panel to send/change the parameters, and my admin screen looks a little different:



The z-wave device I wish to update is on Port 6  ( which I guess is 'node id' and so the first field )
The Parameter I wish to change is 14
The value I wish parameter 14 to have is 1

Thanks Hari

As I do not have Monostable/Momentary light switches, I believe I need to change a switch parameter for the Fibaro z-wave dimmer module (Parameter 14 to value 1), to support my bi-stable existing UK light switches.

Is it possible to make this parameter change using LinuxMCE/Dianemo?

My tricklestar 200ZW-EU remote appears broken (lack of lights) - have ordered and will try replacing the battery.

I wondered if I can use another remote with my tricklestar USB 300ZW-EU,  as I don't appear to be able to find a UK supplier for a replacement tricklestar remote?

If so are there are recommended ones beyond the Aeon Labs Minimote which came up when I searched the forum.

Update ran just fine,  I look forward to the wiki updates, so I can have a try of the new telecoms features.

I figured out that following options allowed me to control/view the camera. This all works when i'm using a normal webbrowser.

Try :

http://10.10.10.10/kmotion

I add my cameras in there and use it as the interface for monitoring, and setting it to record when there is motion. Then reviewing archive footage.  It supports my Axis PTZ cameras and moving.

Assuming that your real Squeeze devices have never been allowed to connect to the LAN side of your NC before then you should ....

Squeezeslaves are virtual Squeezeboxes that can be created on your NC (or MM's) and they make use of 2 of your physical audio outputs each.

Thanks Andrew, Squeeze hardware devices added - I suspect I will continue to control them through dedicated Squeeze hardware controllers, and Squeeze Apps for Android/iOS,  but any issues adding them into same rooms/zones as MM's?

Virtual Squeeze added to core and tested working fine.

Tried adding one to a MM, and it does not appear to work.  
Added the 1964 template to MM, then added #58 template under the Slim Streamer on the Core - matching fake MAC address on both.  Did a reload, and ran Start_SqueezeBox_Slaces.sh
In the Logitech Media Server web interface ( http://core.address:9000 ), I see all my Squeeze Hardware devices, plus the virtual squeeze device on Core, but no device for the MM.
Room assignments/zone is the same as the MM settings.

Anything I can check?