Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mardibloke

Pages: 1 2 [3] 4
31
Installation issues / Re: IP Camera in 1004
« on: July 25, 2012, 12:12:01 pm »
Add as Motion Wrapper,  the wiki covers it very well:

http://wiki.linuxmce.org/index.php/Monitor_surveillance_cameras#Adding_IP_Cameras_under_Motion_Wrapper

What I do not see in the manual for you IPCAM, is a link for a static image from your camera.

For example, my Axis cameras the link is : /axis-cgi/jpg/image.cgi   or my other cameras : /mjpg/video.mjpg

You need to figure that out for your camera.


32
Installation issues / Re: Dianemo S - Networking
« on: July 23, 2012, 09:21:06 pm »
Sorry for bothering you Andrew, now working fine.

I forwarded all ports from my router to 192.168.1.10

Then just setup the firewall on Dianemo.

Maybe some extra reboots/restarts of router/switch/dianemo helped this time.


Is the firewall in Dianemo/Linuxmce regarded as being secure?




33
Installation issues / Dianemo S - Networking
« on: July 23, 2012, 08:13:40 pm »

I had some firewall/NAT rules setup in my router to support things like XBOX gaming and my FTP server.

Adding the Dianemo/LinuxMCE between these services and my router,  I wonder how (best) to set this up.

Internet provider >>> Router (NAT/Firewall) >>> LinuxMCE/Dianemo >>> Home network Services

My router is 192.168.1.1
Dianemo WAN 192.168.1.10
Dianemo LAN 192.168.0.1

LAN devices 192.168.0.x




34
Installation issues / Re: Dianemo S - ZWave
« on: July 03, 2012, 09:45:14 am »
Thanks chaps,  that was exactly the issue.

Sorted now.


35
Installation issues / Dianemo S - ZWave
« on: July 02, 2012, 08:26:14 pm »
Following the guides here:

http://wiki.linuxmce.org/index.php/Dianemo_S#ZWave_Devices

and here:

http://wiki.linuxmce.org/index.php/ZWave#SUC.2FSIS_Mode_.28recommended.29

I get to the part to add the Tricklestar Remote,  which fails, on the Tricklestar remote I get a RED light.

Have tried several times/reloads.  I made this work in the past,  and remember something odd about the process I had to do - maybe around the timing of the steps.

Sending any commands to the zwave device I get : RESP: Delivery failed


36
Thanks so much for the pointer.

Rebooted my internet router, rebooted the core, and all ok again.


37
Installation issues / Dianemo S - Stalled at Dianemo Flashing Logo
« on: July 01, 2012, 09:03:15 pm »
Whilst adding some firewall rules, appeared to get a hang,  did a shutdown -r from console, and now at boot get as far as the flashing Dianemo logo.

dmesg output attached.

Anything I can check for more information?


38
I thought in the AV Wizard (after choosing resolution) there is a later screen where you can resize/reposition the image on the screen - did you not get to that screen?

39
Installation issues / Dianemo S - MythTV - Directory Setup
« on: June 12, 2012, 06:59:11 pm »

What directory structure should I use to best integrate MythTV with Dianemo?


40
Installation issues / Re: Dianemo S - DHCP Server
« on: June 12, 2012, 04:12:50 pm »
Thanks Andrew - all working fine now.

41
Installation issues / Dianemo S - DHCP Server
« on: June 12, 2012, 02:46:56 pm »
Any known issues,  suggestions of things to check if DHCP clients on LAN side are not getting an IP address?

Was working fine, before changing LAN/WAN addressing on Core -  :-[

12.04 32bit, recent fresh install of Dianemo.

Devices with Fixed IP address on LAN side can Browse internet and dianemo admin pages
Firewall on Dianemo currently off
Can Browse internet and LAN devices from Core

See attachment for settings - have tried enable/disable/restarts of core.

42
Shot of part of Dianemo's UK distributor RedLine's stand at the CEDIA Home Technology Event in London 28-30 June 2011

Great looking stand Andrew, am sure it was a busy few days.  Had tickets and plans to attend, but end of month work got in the way at the last minute.

- --
Rod,  UK


43

However currently the Duet controllers themselves are not fully integrated.


Just checking that you have you seen that firmware (in the last year or so) that on the Duet controllers allows them to appear as just another Squeezebox Receivers, and use their built in speaker for audio playback - that was how I was thinking it might work.

- --
Rod,  UK

44
using your iOS device as a portable Squeezebox :-)

Andrew, I'm thinking this would maybe also work with the Logitech Duet controllers?

http://www.logitech.com/en-us/speakers-audio/wireless-music-systems/devices/3817

- --
Rod,  UK

45
Marketplace / Re: Complete Multi room Dianemo/LinuxMCE System
« on: December 14, 2009, 08:21:48 pm »
I use HDMI to AMP

Pages: 1 2 [3] 4