Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - MANDINGO

Pages: 1 ... 12 13 [14]
Users / lost some interrupts at 1024
« on: February 18, 2008, 05:43:11 pm »
Any one else getting this error message from the console dmesg output,
lost some interrupts at 1024
just keeps on looping !!!!

Users / Webdt 375 and Bluetooth
« on: February 18, 2008, 02:34:43 am »
Can any one help me on getting my Webdt to work with bluetooth, the problem is, is that the dcrouter see the unit as a mobile phone not sure what to do here........  any help would be great thanks

Users / Re: LMCE on Dell SX270
« on: February 13, 2008, 01:07:29 am »
First Things first you have to flash to the lastest bios to get the pxe boot feature

i have xp on my drive but i just tell it to boot of the network and set the WOL for the nic also.

Users / Re: LMCE on Dell SX270
« on: February 09, 2008, 08:12:18 am »
I have 2 of them that i use for MDs since they are so quiet as far as the ui2 thats a no the card cant handle it i just use the basic, still rocks for a little machine though

Installation issues / ISO PROMPT BUG
« on: February 09, 2008, 05:09:37 am »
Found this bug that if you install Kubuntu first then copy iso images to the drive for the install of mce, i copied disk 1 and 2 as iso files and then the kubuntu cd also so the install would be faster and have not to cache the cd. During the setup process it asks for the cds When you point to the first disk iso thats ok then point to second disk thats ok but the third prompt does not ask for the kubuntu disk but the linuxmce disk 2 again, i just point to the kubuntu on the third prompt and all is well.  I installed 3 time in this same fashion just to make sure and yes its a bug this doesnt happen if you cache from the cds and not use the iso on your drive, so its just a mistake in the prompt for the iso its prompting for linuxmce disk 2 instead of kubuntu disk .....

Users / Changed Core IP now md wont boot
« on: February 09, 2008, 01:04:02 am »
 >:( This is driving me crazy i changed the internal ip of my core and now my md wont boot but if i change my core internal ip back to the old the md will boot.

After changing the ip in the core i removed all refrence to my md from the director panel and the orbiter panel and removed the folder under diskless boot as so the core will find it as new, and yes dhcp is working i recieve valid ips for my laptops.  Is there a .sh file that didnt get changed when i changed the ip or a parameter somewhere ? any help would be appreciated.

Fixed the problem
Had to hard code the new cores ip address in the and the for it to work and it did  :-\ thats ashame cuz you shouldnt have too

Users / Re: Intermatic Ha22 usb stick
« on: January 31, 2008, 10:52:10 pm »
Hari i had to add a couple of changes but now works completely with intermatic could u post the codes below into the svn thanks

sorry about the files but only place i could post them   :-\

Users / Re: Intermatic Ha22 usb stick
« on: January 30, 2008, 12:12:46 pm »
i have a question i am adding some info to the spcp8x5.c and spcp8x5.h i have the vid and pid for the intermatic, but i dont know the complete usb device id for now i have placed them as

the .c file
{ USB_DEVICE(SPCP8x5_INTERMATIC_VID , SPCP8x5_INTERMATIC_PID)}, need to replace the INTERMATIC with the right info

the .h file
#define SPCP8x5_INTERMATIC_VID   0x04FC
#define SPCP8x5_INTERMATIC_PID   0x0204 

any help would be great and yes the drivers work just wanna add intermatics info in also if this can be done this way ! im comming up with unknown symbol usb_serial_disconnect etc....

Users / Intermatic Ha22 usb stick
« on: January 28, 2008, 07:13:08 pm »
Went to CES 2008 and spoke to the fokes over at intermatic and bitched about the linux drivers not being available....
Got a phone call today telling me that they sent me a copy of the linux drivers they have so im gonna give it a try and see if i can get this thing working ill let you guys know....   ;D

Ok got home and found that i need some help with these drivers i posted a copy here

any help would be appriciated

Pages: 1 ... 12 13 [14]