Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - coley

Pages: 1 [2] 3 4 ... 33
Users / Re: zwave network lockups/delays
« on: August 22, 2014, 05:18:18 pm »
It is probably some HTML/CSS problem that appears in chrome. You could try to use a different browser.
I find firefox to be the best for viewing the advanced zwave page, I found it unworkable with chrome.


Developers / Re: squeezelite as an alternative to squeezeslave
« on: August 14, 2014, 05:43:50 pm »
That is my plan too - don't break existing when adding new.


Developers / Re: O2 Joggler As full MD - Testing needed
« on: July 22, 2014, 06:46:00 pm »
Can you make the edits you require on the diskless image of your joggler MD on the core using chroot?

/usr/pluto/diskless/<NN> where NN is the device id of your joggler MD.


Developers / Re: squeezelite as an alternative to squeezeslave
« on: July 18, 2014, 05:03:58 pm »
I've done this by adjusting the script. But this isn't the right way to do it.
Squeezeslave could be replaced by squeezelite or I don't see a reason either why they couldn't co-exist - why did they need to be swapped? can you point me to the discussion in the forum?.

The existing template and script could be extended to run either binary - but that adds additional package dependencies that squeezeslave doesn't require.
Adding Squeezelite to trusty to coexist with squeezeslave, on the surface, looks manageable.
Adding it to precise is that bit harder with the packages not being available from linuxmce/kubuntu repos.

@phenigma - you did a lot of work with the packaging setup and addition of Raspi stuff - can you advise on my initial queries?


Developers / Re: squeezelite as an alternative to squeezeslave
« on: July 16, 2014, 06:13:57 pm »
Oh, they do. I was just looking for "the right way" to add them.


Developers / squeezelite as an alternative to squeezeslave
« on: July 16, 2014, 02:24:06 pm »
I wanted to swap out my squeezeslave instances with squeezelite as the former is no longer actively developed and also cannot handle Spotify streams.
Squeezelite is available on trusty but you have to build it yourself for precise.
I went digging to find out how to add it, packages+DT, "the right way" to LMCE.
From this effort I have a number of questions;

 - I found a git clone on the squeezelite site with additions to support building a deb package. Turns out Uplink did this work. How can this be used by Linuxmce?
 - To build this deb other packages are required - again not on precise, but available via another PPA, Can these be added with the package manager?
 - Can DTs be copied? or one based on another?


Users / Re: New Fibaro Zwave multisensor FGMS-001
« on: June 24, 2014, 05:28:11 pm »
I went to check mine on 12.04 but one seems to have disappeared from the devices list.
I hadn't set anything up to react to events.
I'll try and investigate


Users / Re: New Fibaro Zwave multisensor FGMS-001
« on: June 13, 2014, 12:56:31 pm »
What version of LinuxMCE are you running?
If you are using 1204 there is a very helpful page available on the webadmin for viewing and diagnosing problems with the Zwave setup, see

I'm guessing the others sensors of the multi-sensor don't show up under Zwave Embedded Climate Interface section in your devices tree?


Developers / Re: MPD integration
« on: May 21, 2014, 08:24:54 pm »
any progress here.......

Users / Re: Joggler install script
« on: April 04, 2014, 05:05:23 pm »
I might give this a bash later and see how it goes.
I had this up and running manually before on 10.04.


Users / Re: Where to debug squeezeslave not starting?
« on: March 28, 2014, 01:14:47 pm »
It seems to be an issue - I don't see them autostart on my 12.04 core.
I had to start them via rc.local on 10.04 as per the wiki - or at least I set them up initially that way. I'm guessing the DT has been updated since as it now has a launch script.


Users / Re: 12.04 black screen
« on: March 28, 2014, 01:12:32 pm »
What UI are you running; 1, 2, 2+alpha?

Users / Re: Where to debug squeezeslave not starting?
« on: March 26, 2014, 01:48:48 pm »
Have you verified that squeezeslave can actually start with the parameters you've supplied in your device?
What happens when you start an instance in a terminal with the same parameters?


Users / Re: Audio amp suggestions requested
« on: March 19, 2014, 05:28:16 pm »
AudioSource do autosensing amps which seem to work quite well and are not too expensive.
Can't talk from experience as I don't have them.


Users / Re: Automatic adding Internet Radio streams to LinuxMCE
« on: March 18, 2014, 11:51:43 pm »
I've recovered it from the old forum:
Thanks for that possy


Pages: 1 [2] 3 4 ... 33