Messages

46

Users / Re: Incoming call ends media play instead of just pause-anyone can confirm this?

« on: August 21, 2008, 09:29:06 am »

Hi
I have the same problem in 710RC2
so it still a problem 

47

Users / Re: Australian Z-Wave....

« on: August 07, 2008, 09:30:09 am »

Hi colinjones

I would give Smarthome  a call as there are them main supplier for all the X10 stuff  www.smarthome.com.au

 

48

Users / Re: MSI Media Live VFD Working

« on: July 30, 2008, 02:12:17 am »

Hi Andrew

yes i know that but it is working now
 Is the  HDMI Audio working on yours ??

49

Users / Re: MSI Media Live VFD Working

« on: July 29, 2008, 05:02:04 am »

Hi all
I have tested the VFD in Mythtv and it works the same as it does in VDR as well

But I have also noticed that HDMI audio is working as well now, could some one else test and see if their HDMI audio is working as well

Thanks
Chris 

50

Users / Re: MSI Media Live VFD Working

« on: July 25, 2008, 05:23:09 am »

mm
I have tried it as well a it still as black as it was before no go at all
you must have changed something else to make it work

51

Installation issues / Re: VOIP setup/Providers Australia

« on: July 21, 2008, 07:57:41 am »

Hi Justdeb
I use voipwa as my provider but i am a bit biased i own the company but if i can help with you voip setup please let me know

52

Users / Re: Happauge Wintv-Nova-T-500

« on: June 30, 2008, 01:39:29 am »

Hi

I am still having problems it is like the options usbcore autosuspend=-1  has stoped working and the card is going to sleep after sometime

53

Users / Re: Happauge Wintv-Nova-T-500

« on: June 26, 2008, 05:21:50 am »

Hi pga57
thanks i will   try it as well and let you know how i get on

54

Users / Happauge Wintv-Nova-T-500

« on: June 24, 2008, 02:04:48 am »

Hi all
I am having some problems with my setup up i have a Hauppauge Wintv-Nova-T-500 install and i am using Mythtv all works fine most of the time but probably once a day i get no signal strength and myth can't get a channel lock
Now if i do a quick reload router all is fine again till next time which could be 1 day or two days but it will do it again
I have made some changes to /etc/modprobe/options this is what i have added

options dvb-usb-dib0700 force_lna_activation=1    (this option turns the LNA on)
options usbcore autosuspend=-1    (this option stops the card from going into standby)

Any help would be nice as this problem has been driving me mad

55

Users / Re: Avermedia 777 TV Quality issues

« on: June 18, 2008, 03:37:21 am »

Hi

I am using the Hauppauge Nova-T-500  and there are working well for me and i am in Perth/Australia
 
Hope this helps

56

Users / Re: How to setup a Disked Media Director for MCE 7.10

« on: May 01, 2008, 02:10:19 am »

First thing to do is pull the hard drive out of the Media Director then go in to the bios and tell it boot of the network card and try that you might get some were

57

Users / Re: New hardware switch & NIC for MD network setup -any comment?

« on: April 23, 2008, 07:43:23 am »

Hi gunsmoke
I am using a intel pci-e ethernet card and it just works as fare as the switch goes ether switch will do the job

Hope this helps

58

Users / MSI Media Live

« on: March 26, 2008, 02:16:52 am »

Hi all
I just brought my self a MSI Media Live and it works very well as a MD but i can not work out how to get the VFD working
Is it possable to get it working ??

59

Installation issues / Re: Windows MCE Receiver Beta 4

« on: March 05, 2008, 05:46:15 am »

All sorted

My Fault i had a IMON VDF Panel pluged in as well and that was causing some sort of conflict any way working Now

 

60

Installation issues / Windows MCE Receiver Beta 4

« on: March 05, 2008, 04:23:35 am »

Hi
I have been trying for days to get my Windows MCE Receiver working and for the life of it want work
it is being found by linuxmce and is loading the right module for it mce_usb2
If i tail the system.log  it gets found as a Philips Ehome IR Receiver
But if i try to use the remote which is a mce remote that works on another MD fine this MD has a built in Receiver which is also found as a mce_usb2 device all works fine
But it want work with the  Philips Ehome IR Receiver

Any help would be good

Thanks