1
Users / Internal Interface
« on: September 13, 2007, 11:58:15 pm »
When I installed MCE it only had 1 interface card. ETH0. I have added a second card for the internal network. Kubuntu shows 2 cards ETH0 and ETH2. However; LinuxMCE only shows ETHO and ETH0:0 both of which have the same mac address per the view IP address from Launch Manager.
Here is the info from Advanced=>Network=>Network Settings
Number of network adapters: 2
Your core has the following network adapters:
1. External network card eth0
Use a static IP address
Core's IP address: ...
Subnet mask: ...
Gateway: ...
Nameserver (DNS) #1: ...
Nameserver (DNS) #2: ...
2. Internal network card eth0:0
IP address: ...
Subnet mask: ...
Here is IFCONFIG:
eth0 Link encap:Ethernet HWaddr 00:11:09:31:55:9E
inet addr:*.*.*.* Bcast:*.*.*.* Mask:255.255.255.0
inet6 addr: fe80::211:9ff:fe31:559e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:21856 errors:0 dropped:0 overruns:0 frame:0
TX packets:18126 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:26602262 (25.3 MiB) TX bytes:1570796 (1.4 MiB)
Interrupt:20 Base address:0x6f00
eth2 Link encap:Ethernet HWaddr 00:90:27:8E:FA:30
inet addr:192.168.80.1 Bcast:192.168.80.255 Mask:255.255.255.0
inet6 addr: fe80::290:27ff:fe8e:fa30/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1604 errors:0 dropped:0 overruns:0 frame:0
TX packets:75246 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:224356 (219.0 KiB) TX bytes:3170237 (3.0 MiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:31268 errors:0 dropped:0 overruns:0 frame:0
TX packets:31268 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4417717 (4.2 MiB) TX bytes:4417717 (4.2 MiB)
Can anyone suggest how to get MCE to identify the second card and use DHCP server on it? Do I have to reinstall?
Here is the info from Advanced=>Network=>Network Settings
Number of network adapters: 2
Your core has the following network adapters:
1. External network card eth0
Use a static IP address
Core's IP address: ...
Subnet mask: ...
Gateway: ...
Nameserver (DNS) #1: ...
Nameserver (DNS) #2: ...
2. Internal network card eth0:0
IP address: ...
Subnet mask: ...
Here is IFCONFIG:
eth0 Link encap:Ethernet HWaddr 00:11:09:31:55:9E
inet addr:*.*.*.* Bcast:*.*.*.* Mask:255.255.255.0
inet6 addr: fe80::211:9ff:fe31:559e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:21856 errors:0 dropped:0 overruns:0 frame:0
TX packets:18126 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:26602262 (25.3 MiB) TX bytes:1570796 (1.4 MiB)
Interrupt:20 Base address:0x6f00
eth2 Link encap:Ethernet HWaddr 00:90:27:8E:FA:30
inet addr:192.168.80.1 Bcast:192.168.80.255 Mask:255.255.255.0
inet6 addr: fe80::290:27ff:fe8e:fa30/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1604 errors:0 dropped:0 overruns:0 frame:0
TX packets:75246 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:224356 (219.0 KiB) TX bytes:3170237 (3.0 MiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:31268 errors:0 dropped:0 overruns:0 frame:0
TX packets:31268 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4417717 (4.2 MiB) TX bytes:4417717 (4.2 MiB)
Can anyone suggest how to get MCE to identify the second card and use DHCP server on it? Do I have to reinstall?