Connect the PC to internet or use wright repositorie

1/ open a shell
2/ type "sudo apt-get install mysql-admin"
3/ type yes
4/ type "sudo apt-get install mysql-query-browser" (to modify the table data)
5/ type yes

then go to the K menu of kubuntu

For more infos:
http://doc.ubuntu-fr.org/mysql_outils

o, I'm sorry, I re-read your post:

Integration with motion is not fully done. Actually only config files are auto generated from settings in admin page and then more or less motion works on its own. Communication happens only on few occasions :
- when LMCE needs snapshots it sends signal to motion and than motion_wrapper reads latest snapshots and send it back (view camera scenarios for instance)
- when motion is detected, then proper DCE messages are sent. In ThreadX.conf you have :

Code:

# sending pluto tripped on/off events on motion start/end
on_event_start /usr/pluto/bin/MessageSend 127.0.0.1 51 -1001 2 9 25 1
on_event_end /usr/pluto/bin/MessageSend 127.0.0.1 51 -1001 2 9 25 0

and that cause sensor tripped on and tripped off events that are sent to LMCE. Currently even motion http interface is not supported - I did all the work I could at that time, but now have no time to enhance it. But everone is welcome to rool sleeves up, I'll help as much as I can with internals and how to do it...

BTW, I think that you have current house status displayed on main page of Orbiter...

So I would like to have the work you did and some how to in order not to loose to much time !!! Then I would help coding !!

however, why on main linuxmce page, there is

Security: Uses your existing home alarm, surveillance cameras, lights, phones and tv's to notify you on your mobile phone of any security alerts with the option of reseting the alarm or broadcasting your voice in the house over the tv's

[notify you on your mobile phone of any security alerts]

hy and thanks for the answer there is 2 days I try to figure outwhy'not working !!

Do you have any key starting to work on it !!
I will need this fonctionnalities !!!!
You said it's not implemented, so why on the first linuxmce.com webpage you can read:

Security: Uses your existing home alarm, surveillance cameras, lights, phones and tv's to notify you on your mobile phone of any security alerts with the option of reseting the alarm or broadcasting your voice in the house over the tv's

Thanks for replying, and given any help. I can work on it!

as described in this thread:
http://forum.linuxmce.org/index.php?topic=2542.0

I setup my security camera (controled by the motion detector), that is working.
Then I setup the "active sensor" in admin website.
I set it up as bellow:
* monitor mode unchecked
* disarmed mode: N "unchecked", action "do nothing"
* armed-away: N "checked", action "Security"
* armed-at home: N "checked", action "Announcement"
* sleeping: N "checked", action "Snap picture"

rest as armed away


My problem is that I change the mode and:
1/ no info about the current mode in the top bar
2/ the mode is changed (see in statut of the admin website), but video still record on motion, picture as well, like if there is no difference between mode!! and before, I had the security breach that appears when motion detected, but now I don't have the alert any more, and if I reset the parameters (monitor mode  unchecked, all N checked and all in "security", it come back) !!

It's very painfull. If someone could help I'll be gratefull.

no, I still got problems with the security mode, 'll make a new post!

To do an update,
I did:

1/ go to /usr/pluto/bin
2/ ./LMCEUpdate_DownloadXml.sh
3/ ./LMCEUpdate
4/ still downloadind, however I guess I have to do
./LMCEUpdate_Apply.sh

Other solution as described in wiki
Another way to perform system update is use the Orbiter:
  More --> Advanced Options --> Force Upgrade Now


The wiki has to be update !!

I thing my problem was that I needed to reboot computer when change active sensor, reload and regen is not enough !!

For the state, in the top banner, I've got Ox and nothing else... will figure out why !

In fact I will make a link I guess in the "/home/public/data/video" folder

1/ For my security mode problem, when I change mode, bellow alert, I have:
camera X (announce only), I guess it's the part of the problem. However I didn't check the monitor mode buton

2/And It don't display the state mode in top bar

For the path I have to modify the "target dir value", I will try in the configuration field !
target dir value = /home/media/N°ofCamera

hoppe will not broke link with cellphone alert !!

than's you bulek your the best !!!

you are wright, all videos are stores there in a particular way !!! However, will try to change the stored path in order to see it in the media directory if the link send to mobile phone still work !!

Thanks.

For the state, I though there as been in the gui display of the MD there should be on top banner the state. In fact my other problem is that the alert mpg video don't display when I change the parameters for disarmed mode (snapshot for example), and let security in armed mode. The disarmed mode is ok but armed don't show message as in scenario event 16 or 17 I don't remember !!
ps: also do you know why when security "breech " appears, a move or click of the mouse... don't turn off the display of the mpg file

thanks helping !

Hello,

I still continue finding some solution for my need and digg in the http://www.lavrsen.dk/twiki/bin/view/Motion/MotionGuide website for info.
The parameters are:
http://www.lavrsen.dk/twiki/bin/view/Motion/MotionGuideGettingItRunning
http://www.lavrsen.dk/twiki/bin/view/Motion/MotionGuideBasicFeatures#Capture_Device_Options_The_Basic



1/ I'm looking for a way of making video recorded when motion detect it! I though it was in the motion field, putting 3 make it record but not find any video file.
2/ The worst is that when I change the action in "active sensor" for each mode, if I make just snapshot in disarmed mode then reload, then when I change mode to armed, alarm don't work at all like if the mode was still in disarmed ! Is there a way of showing the mode in the gui !! I tried some other conbination in the alctive sensor, but I got a probleme with the mode !!! shity ! because the threadx.conf is correct and motion.conf also for record when motion !
any help would be appreciate !

I fixed the second point going in admin site, there is "active sensor" where you can choose action for each mode !!!

I will do the french translation since I will be able to connect my xp computer on the core !!!

For the door phone, I have the same project 

I 'v got a little problem with floorplan, when I drag and drop the camera in floorplan wizard, I've got the camera on the MD, but When I click on it, I can't have the view button activ Any idea? Is it beause it's controled by motion wrapper

In fact I put camera instead of motion detector !

2 bugs!
1/ If I got many floorplan, if I click on one camera button, then not click on view button but on another floorplan, the camera button still display on other floorplan that I didn't drag n drop on it !!!
2/ I don't know if it's bug (I have to see how motion wrapper work), but If i'm on security disarmed, the alert still come when mouvemment are detected on the camera !!! Have to figure out why !!

you was right, it's working, I put

netcam_url  http://192.168.0.20/VIDEO.CGI

in configuration field !!
However I would be great to make a driver with a java applet !!

I 'v got a little problem with floorplan, when I drag and drop the camera in floorplan wizard, I've got the camera on the MD, but When I click on it, I can't have the view button activ Any idea? Is it beause it's controled by motion wrapper

thanks for your great help !!