Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - yrucrem

Pages: [1]
Installation issues / Re: No files in Pluto folder?
« on: February 08, 2011, 07:01:32 am »
Ok. Thanks for clarifying, rperre!

I used my downloaded dvd snapshot again and followed the DVD installation now. But when I ran the LinuxMCE desktop button most seemed ok except for the following:

Get:51 intrepid/main libgnomevfs2-0 1:2.24.0-0ubuntu1 [264kB]               
Err intrepid/beta2 pluto-plutoutils                           
  The HTTP server sent an invalid Content-Range header                                                     
Err intrepid/beta2 pluto-serializeclass                       
  Bad header line                                                                                           
Err intrepid/beta2 pluto-dcecommon                             
  Bad header line                                                                                           
Err intrepid/beta2 pluto-pluto-main-db                         
  Bad header line                                                                                           
Err intrepid/beta2 pluto-add-software                         
  Bad header line                                                                                           
Err intrepid/beta2 lshwd 2.0-rc4-1pluto14                                           
  Bad header line                                                                                           
Get:52 intrepid/main libgnome2-common 2.24.1-0ubuntu4 [340kB]   

Are these important files?
And also my installation is now stuck in:

make KERNELRELEASE=2.6.27-7-generic..............................................

How do I solve these?


Installation issues / Re: No files in Pluto folder?
« on: February 07, 2011, 04:42:21 am »
bongowongo and rperre thanks for the replies.

That was my first setup. Got the core running but fails in the MD. I remembered there were quite a number of warnings during the setup for that one so I decided to do another setup based on the instructions given posted in that wiki page you gave. I used a newer snapshot than the one I previously used. In the first try I used the LinuxMCE desktop shortcut to install but got a lot of problems. Next setup try I used the pre-install-from-repo, mce-install and post-install codes. Everything seemed ok but after reboot found out the pluto folder only contained deb-cache.

Installation issues / No files in Pluto folder?
« on: February 06, 2011, 04:45:46 pm »

I've been trying to setup a hybrid LinuxMCE but cannot setup an MD properly. Over the weekend I tried to make a new setup by following the instructions here including the source list. There were some slight glitches but found the solutions online also and was able to finally complete this with no more errors:

sudo su - #This might ask for the password you specified earlier during the install of kubuntu.
apt-get update
sudo apt-get dist-upgrade
wget -c http :// deb . linuxmce . org/ubuntu/new-installer-latest.tar.gz
tar xvf new-installer-latest.tar.gz
cd new-installer

After reboot, however, I expected to see the AVWizard but I only got the command line login instead and a message saying

kinit: trying to resume from /dev/disk/by-uuid/a13c3a08-1a11-47bd-984e-2a11edb72156
kinit: No resume image, doing normal boot...

I tried to run the AVWizard file from the instructions online and got surprised there's no such file. I took a look at the pluto folder and saw that it only contained a /deb-cache folder. It's supposed to contain the /bin folder and other stuff, right? Right now I'm seeing only /deb-cache with a lot of *.deb files.

I have no idea what to do with this. Any idea what went wrong and how I can remedy them?


Users / Re: Sharp Aquos
« on: December 12, 2010, 06:23:39 pm »
I've been trying to connect a Sharp LCD TV to my Linux MCE test setup but haven't been successful yet. Want to connect it via HDMI and/or VGA cable(w/ audio). After using setup wizard I still can't find it. Is there something else I have to configure?

This is the model: Sharp Aquos LCD TV (LC42A66M)

Any feedback will be greatly appreciated. Thanks!

Installation issues / Re: Black screen after installation is finished
« on: September 25, 2010, 06:54:21 pm »

I'm a linux noob and I'd like to test out the LinuxMCE installation first before trying it out on a dedicated pc. However, I just have a laptop with integrated graphics (Intel HD) and tried to install it virtually. So far it worked up to the AV Wizard. After clicking the I Agree button it proceeded to the orbiter setup then after that one has completed everything went black (with mouse cursor).

I did try different video settings already but I still get the black screen after the orbiter thing. I checked my graphics properties including the display which says LVDS connector with 1366 x 768 supported mode. I saw that in the connector list in the AV wizard but the supported resolution is not listed there (does this matter?).

Is it just not possible to test out virtually with notebooks?

Any clarification is greatly appreciated. Thanks.

Pages: [1]