Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Riggs

Pages: [1] 2 3 ... 13
1
Users / Re: LinuxMCE 10.04 Gtalk Setup
« on: December 28, 2012, 05:32:16 pm »
heres some new logs, I attempted multiple outgoing calls with no success, they all hung up after 3 rings

2
Users / Re: LinuxMCE 10.04 Gtalk Setup
« on: December 26, 2012, 09:22:53 pm »
Just an update.
I tried to call the Gvoice number, my sipsoft phone shows the call and i can answer it
but the caller hears ringing only then they get the Gtalk voicemail.

3
Users / Re: LinuxMCE 10.04 Gtalk Setup
« on: December 26, 2012, 06:03:17 pm »
i just called it a patch , but what i did was remove the old and put in the new

4
So when i start myth tv, it will randomly switch between watch tv, recordings and a number one on screen.
it will then ask me if i want to reset the backend, i say yes, it then says it can not connect to the back end.

5
Users / Re: LinuxMCE 10.04 Gtalk Setup
« on: December 26, 2012, 05:37:20 pm »
I put your patch in (db_phone_config.sh) now it does not show a status and i can not add a sip soft phone to test.
when i add a sip soft phone in the LMCE admin page, there is no profiled ext or password

6
Users / Re: LinuxMCE 10.04 Gtalk Setup
« on: December 24, 2012, 11:34:36 pm »
Ok after putting the username in the phone number filed, it show connected but i can not make outgoing calls, they just ring endlessly.

asterisk log full:
[Dec 24 16:25:23] NOTICE[23736] iax2-provision.c: No IAX provisioning configuration found, IAX provisioning disabled.
[Dec 24 16:26:18] VERBOSE[25259] chan_gtalk.c: OOOOH domain = riggsusa
[Dec 24 16:27:00] VERBOSE[26875] chan_gtalk.c: OOOOH domain = riggsusa
[Dec 24 16:27:50] WARNING[2379] chan_sip.c: No valid transports available, falling back to 'udp'.
[Dec 24 16:27:50] NOTICE[28066] chan_iax2.c: Ignoring bindport on reload
[Dec 24 16:27:50] NOTICE[28066] chan_iax2.c: Ignoring bindaddr on reload
[Dec 24 16:27:50] NOTICE[28066] iax2-provision.c: No IAX provisioning configuration found, IAX provisioning disabled.
[Dec 24 16:28:19] WARNING[29142] pbx.c: Extension 'vmx', priority 54 in 'macro-vm', label 'vmxopts' already in use at priority 52
[Dec 24 16:28:19] WARNING[2379] chan_sip.c: No valid transports available, falling back to 'udp'.
[Dec 24 16:29:23] WARNING[30382] pbx.c: Extension 'vmx', priority 54 in 'macro-vm', label 'vmxopts' already in use at priority 52
[Dec 24 16:29:23] WARNING[2379] chan_sip.c: No valid transports available, falling back to 'udp'.
[Dec 24 16:29:25] VERBOSE[30388] chan_gtalk.c: OOOOH domain = riggsusa

7
Users / Re: LinuxMCE 10.04 Gtalk Setup
« on: December 24, 2012, 10:32:51 pm »
So we don't enter a phone number..
There needs to be a HowTo for this or the script needs to change to allow for the correct values.

8
Users / Re: LinuxMCE 10.04 Gtalk Setup
« on: December 24, 2012, 09:41:39 pm »
it looks like you are putting your username in the phone number section

9
Users / Re: LinuxMCE 10.04 Gtalk Setup
« on: December 24, 2012, 08:55:28 pm »
I've been playing with this for weeks and I have got no where.
As for filling out the username with @gmail.com does not change a damn thing, as for it saving the settings it is hit and miss

10
Developers / Re: Elk Rs232 Protocol PDF links
« on: December 23, 2012, 05:28:22 am »
I'm in contact with Elk Products, to see if they will send me an updated version, I have a account with them from my installer days, I just never thought about it till now.

11
Developers / Re: Elk Rs232 Protocol PDF links
« on: December 21, 2012, 01:54:48 am »
Yeah it sucks but I can't help where it is, I just found it.

12
Developers / Elk Rs232 Protocol PDF links
« on: December 20, 2012, 04:17:38 am »
For any one interested I came across this link for the Elk M1 Gold Rs232 protocol Specs.

http://www.scribd.com/doc/50097012/Elk-m1-Rs232-Protocol

13
Users / Re: CM15A not sending or receiving commands
« on: December 10, 2012, 09:39:43 pm »
Its a old Dell XPS gen5,
I can confirm that the power line signals are transmitting and receiving, but I'm not getting anywhere with RF which is the only reason I use X10 now.
 

14
Users / Re: CM15A not sending or receiving commands
« on: December 05, 2012, 11:33:37 pm »
I have to do some RF tests but so far i think that fixed it i can send PL commands, I cant seem to get a response over RF maybe due a config error on my part

15
Users / Re: CM15A not sending or receiving commands
« on: December 05, 2012, 10:44:19 pm »
I'm in the USA I only use the CM15A for RF motion sensors although i know i have good communication over PL.
I just did a test in windows and AHP work as usual

Pages: [1] 2 3 ... 13