Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Gangsingen

Pages: [1] 2 3 4
Installation issues / Re: New install, Squeezeboxes not working
« on: October 29, 2013, 01:41:48 pm »
Have had this problem for a few years. But since nobody else have had it, I assumed that my old SB2 is faulty. Anyways, here is "my" solution.


Try to connect the SB to the system with the ethernet connection. I have to do this with my SB2 to make it controllable via LMCE. I know that technically it shouldn´t make any difference, but this was the solution for me. Give it a try!

Users / Re: Funding Drive: ZWave Door Locks
« on: September 24, 2012, 07:28:53 pm »
This is awesome!

Exactly what doorlock did you buy?

Users / Re: Funding Drive: ZWave Door Locks
« on: September 21, 2012, 02:13:08 pm »
I´m in with 35€ if paypal transfer is ok!

Should have read the whole thread...... 35EUR sent!

Users / Re: 8.10 + SqueezeBox + Cant play audio via LMCE
« on: April 15, 2012, 11:52:30 am »
I had the same problem with my 10.04 install. The CLI (Command Line Interface) should be activated and set to port 9090.

Any progress here?

Users / Re: New Roaming Orb iOs app
« on: February 15, 2012, 03:24:28 pm »

Thanks guys, enjoying the new RoamingOrb for iOs aswell.

Users / Re: 1wire support
« on: February 11, 2012, 02:24:21 pm »
Where in the sequence do you plug the sensor/s into the interface adapter?

I had mine plugged in all the time!

Users / Re: New PLCBUS driver
« on: February 10, 2012, 03:18:44 pm »
Hi Gangsingen,

Do you solve this problem? i faced this issue also.


Well, yeah....kind of..

  • In webadmin, click "lighting scenarios" in the left-hand column
  • In the room you have specified to have the appliance module, you will have "Autogenerated scenarios" On and Off.
  • Click the On scenario.
  • Change the command from "Set level 100" to "On".
  • Reload the router

This way the scenario buttons "On" and "Off" will work, but in the floorplan the light can be turned off but not on.

Users / Re: 1wire support
« on: February 10, 2012, 02:55:21 pm »
So the steps are?

  • Connect 1wire interface to core
  • Add the 1wire interface in webadmin using template 2161
  • Select the port the 1wire interface is connected to
  • When prompted do a quick reload
  • Once the sensors are detected, another quick reload is needed
  • Now you should have Multilevel Sensors as childs, for every sensor connected to the 1wire bus, in the webadmin
  • Choose the rooms that the sensors are in and add to the floorplan.
  • Another Quick reload should do the job


Spot on, that exactly how I got mine working!

Installation issues / Re: 1004.....squeezebox not working
« on: February 09, 2012, 03:43:34 pm »
Now it works as it should. Just remember to check that the CLI (Command Line Interface) plugin is set to port 9090, NOT 7890.

Users / Re: 1-Wire Deployment
« on: February 09, 2012, 10:50:26 am »

Currently I have a 1-wire interface working and two temp sensors connected to it. The setup is just temporarily installed, as is my whole LMCE setup. I don´t have any idea if all this is possible, but I would like to use my 1-wire network to provide following information to the core.

- Temperatures in all rooms and outdoors.
- Humidity in my bathrooms.
- Motion detection in all common areas (areas in the house except the bedrooms).
- If it is dark or light outside.

With this information I want the core to:

- View present temperatures & humidity on orbiters. Temp and humidity graphs would be awesome to have available, not necessarily via orbiters, but in a web-based environment.
- When movement is detected in any common area except the bedrooms, the "at home&awake" lighting scenarios is activated.
- When no movement have been detected in any of the common areas in 30mins, the "away or sleeping" lighting scenarios are activated.

My idea is that the lighting in the common areas should be completely automatically handled 90% of the time. If I want some specific lighting scenario active, I launch it myself via orbiters.

Installation issues / Re: PLCBus 1141 RS232 cannot connect with PLCBus 2027
« on: February 06, 2012, 10:05:07 pm »
Hi bongowongo,

I'm using linuxmce 0810. Yes, 2027 is an appliance module.

I dont know what wall socket you have where you live, but in europe we have to make sure that the plug-in modules are inserted in the wall socket the right way, try to plug it in upside down" if your socket allows you to do that.

Users / Re: How much HD space do I need for Core + MDs?
« on: February 04, 2012, 09:25:01 pm »
Here is HD-guru Steve Gibsons take on SSD:s.

Maybe something to consider? Love Security Now!

Users / Re: 1wire support
« on: February 04, 2012, 09:03:37 pm »
The interface I´m using is a super cheap chineese variant of the 9097.

In 8.10 it doesn´t work, and isn´t listed with lsusb. But in 10.04 though, it´s listed using lsusb, and once added manually in webadmin the sensors are detected automatically.

Installation issues / Re: squeezebox not working
« on: January 21, 2012, 11:11:36 am »
Hi there!

I think it has to do with this. When I try to install pluto-slim-server-streamer  manually, I get this..

Code: [Select]
The following packages have unmet dependencies:
  pluto-slim-server-streamer: PreDepends: squeezeboxserver but it is not installable
E: Broken packages

Pages: [1] 2 3 4