Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - joerod

Pages: [1] 2 3 ... 11
Users / Z-Wave Siren
« on: July 17, 2014, 02:34:40 pm »

Users / Re: Roku Template 2049
« on: July 07, 2014, 08:29:03 pm »

Users / Re: Roku Template 2049
« on: July 07, 2014, 03:31:48 am »
Well I think i found the problem.  Im using /dev/video0 tuner for mythtv.  if I stop mythtv-backend, reload the cx18 drivers, start mythtv-backend and access the roku scenario everything sounds and looks great, but once I enter myth again the roku scenarios sound stop working..

Any ideas on what I could do to make these co-exists?

Users / Re: Roku Template 2049
« on: July 06, 2014, 09:48:35 pm »
after fixing the hvr1600 template I get picture but no sound....
cat /dev/video0 > test.ts does produce a file with sound; what am I missing?

Users / Re: Roku Template 2049
« on: July 06, 2014, 08:25:26 pm »
Found a problem with the HVR1600 template where device block isnt filled correctly (it should say /dev/video0) and it didnt say anything, and the port were configure wrong as well (they should have a 0 infront of the port number in extra paramters, 0 being the videoX number).

Users / Roku Template 2049
« on: July 06, 2014, 07:36:56 pm »
I'm trying to use template 2049 which is controlling the player correctly
I changed the media type to DVD so that the remote would be more accurate
and that also created the media scenarios that were not being created automatically
but I get no video on screen; i do get remote on orbiters and I can get video if I log in with x-forwarding, change the input via v4l2-ctl  and type mplayer /dev/video0.

DCERouter.log says:
08 07/06/14 13:22:14.146  Received Message from 0 (unknown / ) to 10 (Media Plug-in / Server Area), type 1 id 43 Command:MH Play Media, retry none, parameters: <0x94ffcb70>
 08 07/06/14 13:22:14.147    Parameter 2(PK_Device): 98 <0x94ffcb70>
 08 07/06/14 13:22:14.147    Parameter 29(PK_MediaType): 12 <0x94ffcb70>
 08 07/06/14 13:22:14.147    Parameter 45(PK_EntertainArea): 2 <0x94ffcb70>
 01 07/06/14 13:22:14.148  debug_stream_end MediaStream::MediaStream c1 1010/0x58c2f6c8 source 98 <0x7b3e1b70>
 05 07/06/14 13:22:14.148  MediaStream::GetCurrentMediaFile - no file <0x7b3e1b70>
 05 07/06/14 13:22:14.148  MediaStream::GetCurrentMediaFile - no file <0x7b3e1b70>
 05 07/06/14 13:22:14.148  MediaStream::GetCurrentMediaFile - no file <0x7b3e1b70>
 05 07/06/14 13:22:14.148  Media_Plugin::CheckForAlternatePipes no destination for EA 2 Bedroom (Master) <0x7b3e1b70>
 01 07/06/14 13:22:14.148  StartCaptureCard(): Audio Port Device is 38 <0x7b3e1b70>
 07 07/06/14 13:22:14.148  Event #19 has no handlers <0x9abf9b70>

 38 is the default audio on the capture card, but I see no video device id, video device id should be 32; and that is configure correctly for the device in webadmin -> A/V Equipment.

I though i understood what was going on, but now I'm confused again... Any help is much appreciated.

Installation issues / Re: Embedded ATI Radeon 7000-M
« on: July 06, 2014, 07:33:16 pm »
I commented out CheckVideoDriver in /etc/init.d/a0start_avwizard and verified that the ati drivers are installed.

Now when I run the avwizard the end of the log says:

dlopen: /usr/lib/xorg/modules/drivers/ file too short
(EE) Failed to load /usr/lib/xorg/modules/drivers/
(EE) Failed to load module "viaprop" (loader failed, 7)
(EE) Can't load FireGL DRM library (
FATAL: Error inserting fglrx (/lib/modules/2.6.32-45-generic-pae/updates/dkms/fglrx.ko): No such device

0: /usr/bin/Xorg (xorg_backtrace+0x3b) [0x80eaafb]
1: /usr/bin/Xorg (0x8048000+0x610fd) [0x80a90fd]
2: (vdso) (__kernel_rt_sigreturn+0x0) [0xb777f410]
3: /usr/lib/xorg/modules/drivers/ (xdl_x750_atiddxProbe+0x1f0) [0xb66eb6e0]
4: /usr/lib/xorg/modules/drivers/ (atiddxProbe+0x29) [0xb66648e9]
5: /usr/bin/Xorg (xf86CallDriverProbe+0x182) [0x80b06b2]
6: /usr/bin/Xorg (DoConfigure+0x1c8) [0x8163868]
7: /usr/bin/Xorg (InitOutput+0x1da) [0x80b1c8a]
8: /usr/bin/Xorg (0x8048000+0x1ebbb) [0x8066bbb]
9: /lib/tls/i686/cmov/ (__libc_start_main+0xe6) [0xb74abbf6]
10: /usr/bin/Xorg (0x8048000+0x1e961) [0x8066961]
Segmentation fault at address (nil)

Caught signal 11 (Segmentation fault). Server aborting

Please consult the The X.Org Foundation support
 for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional information.

 ddxSigGiveUp: Closing log
+ VerifyExitCode 'Running /usr/bin/Xorg -configure failed!'
+ local EXITCODE=1
+ '[' 1 '!=' 0 ']'
+ echo 'An error (Exit code 1) occured during the last action'
An error (Exit code 1) occured during the last action
+ echo 'Running /usr/bin/Xorg -configure failed!'
Running /usr/bin/Xorg -configure failed!
+ exit 1
+ StatsMessage Exiting
++ date

Installation issues / Re: Embedded ATI Radeon 7000-M
« on: July 04, 2014, 09:41:12 pm »
Running 10.04

# lspci -nn | grep VGA
0b:0d.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] RV100 [Radeon 7000 / Radeon VE] [1002:5159]

Installation issues / Embedded ATI Radeon 7000-M
« on: July 04, 2014, 07:42:00 pm »
 I have a poweredge 2850 with an Embedded ATI Radeon 7000-M
 AVWizard is not running :(
 /usr/bin/aticonfig: No supported adapters detected
 any ideas on what I could do to get it to work?
 apparently it defaults to: radeon
 and kde looks great with that driver
 but orbiter is acting funny

Users / old server proliant ml530 G1
« on: May 20, 2014, 04:20:25 pm »
I was given an old 2 processor proliant ml 530 g1 ( with scsi drives (5 discs running raid5) 2.5 gigs of ecc ram (PC133MHz Registered ECC SDRAM DIMM Module) power supply array, etc.

The installation went great (network install of 1004).  I was able to configure hdpvr, and two media directors. Everything seems stable and something expected to be slower, but I did not expect logging into a MD via ssh would take 1-2mins to login, playing a video from an MD would take 30-60 seconds to begin playing and 45 - 90 seconds from the moment myth starts to the moment the live stream begins. 

Am I missing something? Do you guys think this kinda of core hardware would cause this kinda of problem?  During these slow load times core CPU is not at 100%.

Any ideas on why some components are working slow while others (screensaver, zwave lights, router reloads, among oothers) work fine?

Users / Re: Purge Camera Archive
« on: May 11, 2014, 03:50:21 am »
Is this really fixed? My camera recordings seem to be erased daily even though purge period is set to 5. Any ideas?

Users / Re: Haven't posted a thank you in a while
« on: March 01, 2014, 11:51:01 pm »
If I could like this post I would so... (LIKE)...

Users / Re: What PVR
« on: March 01, 2014, 11:49:08 pm »
I use mythTV on 1004 using a local cable computer "LibertyCable" connected via rca cables to a HDPVR.  Everything works great, I use the IR Blaster on the HDPVR to change the channels and schedules direct for the guide.  I have very few complaints about myth (most concerning the UI).  I had to configure everything manually, but once it was working Ive had no problems (been about 3 months).

Users / Re: X100P
« on: December 21, 2013, 06:09:48 pm »
Ok, I got it working and from I can tell its working the way its suppose to (no crazy hacks, but yes I had to change code). I will try to document it as best I can in wiki and will try to comunicate with developers to get this committed, but here what I did:

Line: 24 (REPLACE):
Code: [Select]
Line: 106 (REPLACE):
Code: [Select]
<td><B>'.translate('TEXT_HOST_CONST').' / Channel *</B></td>
Line: 366 (APPEND):
Code: [Select]
        elif [[ $protocol == "DAHDI" ]]; then
                LINESSQL="$LINESSQL INSERT INTO $DB_Extensions_Table (context,exten,priority,app,appdata) VALUES \
Lines: 382-387 (REPLACE):
Code: [Select]
        LINESSQL="$LINESSQL DELETE FROM $DB_Extensions_Table WHERE context like '$context';"

        if [[ $protocol == "DAHDI" ]]; then
                LINESSQL="$LINESSQL INSERT INTO $DB_Extensions_Table (context,exten,priority,app,appdata) VALUES \
                ('$context','_.','1','Set','GROUP()=OUT_$LineCounter'), \
                LINESSQL="$LINESSQL INSERT INTO $DB_Extensions_Table (context,exten,priority,app,appdata) VALUES \
                ('$context','_.','1','Set','GROUP()=OUT_$LineCounter'), \

After the configure/installation of DAHDI and /etc/asterisk/chan_dahdi.conf I can access Phone Lines from web admin and add a new FX0 trunk. 

Users / Re: X100P
« on: December 18, 2013, 08:37:31 pm »
once dahdi was installed I had to add the driver to /etc/dahdi/modules file: for the X100P card the driver name was: wcfxo
then restarted dahdi: service dahdi restart
then I noticed in dmesg that the correct module was installed for the card that showed lspci
then I ran dahdi_cfg and dahdi_genconf
it generated the correct configuration files for both dahdi and asterisk, but asterisk did not have the dahdi modules installed so I ran: apt-get install asterisk-dahdi and then uncommented the dahdi module from /etc/asterisk/modules.conf
I then created a /etc/asterisk/chan_dahdi.conf file with the contents of the previously mentioned zapata.conf file.
I restarted asterisk and connected to the console using asterisk -vvvvr
and typing dahdi show channels I can see my card. I can also execute dahdi_tool and see my card.


how do I set my card as the out route now that freebpx isnt available?

Pages: [1] 2 3 ... 11