Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - steven.herr

Pages: [1]
1
Users / Onscreen Orbiter Volume Controls
« on: April 07, 2013, 03:57:58 am »
Hello,

I have installed LinuxMCE 1004 and managed to get a media director up and running, connected my Marantz SR receiver that uses IR codes to a USB UIRT, and created a new template in the AV wizard to control the receiver.  The "test code" buttons work to increase and decrease the volume.  I have UI1 as the Onscreen Orbiter of the media director.  I can play music.  When I use my mouse to open the "remote" of the Onscreen Orbiter I can pause and play the audio file.  I cannot get the volume controls or mute to work using my mouse by clicking on the volume up or volume down of the "remote".  I have rebooted the entire system and it still doesn't work.

Am I expecting something that LinuxMCE cannot do or is there a mistake in my configuration somewhere?

Regards,

Steve

2
Users / HAI Omni IIe on LinuxMCE 1004
« on: April 01, 2013, 05:43:36 pm »
Hello,

I've installed LinuxMCE 1004 and it has detected my Omni IIe panel through the RS232 connection.  Unfortunately, I don't have an idea how to configure the rest of LinuxMCE to integrate with my Omni IIe panel.  Would someone be able to walk me through how to have set up the sensors of the system within LinuxMCE?

Thanks,

Steve

3
Users / LinuxMCE 810 Web Orbiter 2.0 Buttons Link to a Blank Screen
« on: July 04, 2012, 03:36:12 pm »
Hello,

I am attempting to get a Web Orbiter working for workstations and Ipods using Web Orbiter 2.0.  I am able to login and view the Home screen with the buttons.  When I select a button, I am presented with a black/blank screen.  I am able to navigate back to the Home screen by selecting Home at the bottom.  I should also note that the Onscreen Orbiter works fine.  Any suggestions where I have gone wrong?

Thanks,

Steve

4
Users / LinuxMCE-810 RC1 Internal Hard Drive Array Permission Issues
« on: February 02, 2012, 04:57:49 pm »
Hello,

I am running LinuxMCE-810 RC1 and I am a newbie to LinuxMCE.  I have it installed on a typical internal hardrive.  I am able to access and write to this hard drive across the network.

In addition, I have a large internal array of hard drives that I want to utilize as a fileshare across my network.  I have created Device #34: DISK_0_1 (sdb1) on dcerouter-C and chose "public" rather than "LinuxMCE's directory structure".  My difficulty is that I am not able to write to this array despite being able to write to the internal hard drive mentioned above.

I must be missing something simple.  Can someone offer a suggestion so that I don't go messing things up?

Thanks!

Steve

5
Installation issues / 8.10 UI2 Not Available
« on: November 15, 2011, 02:54:23 am »
Hello,

I am attempting my first installation of LinuxMCE 8.10 and have it installed and working with an onscreen orbiter on a hybrid server.  I have an Nvidia 9600 GT video card.  I would like to try to change the skin for the orbiter but the UI2 is not available as an option.

Is there a wizard I need to re-run?  Or, do I have to reinstall and pay closer attention to some of the initial installation choices?

Thanks,

Steve

6
Users / Static IP LinuxMCE Server to Static IP SIP Trunk Provider
« on: October 12, 2011, 03:57:05 am »
Hello,

I have started my first attempt at creating a LinuxMCE box.  I am running LinuxMCE-810 RC1.  My difficulty is in attempting to configure FreePBX.  I live in a rural area where I am fortunate enough to have a local provider that will provide a SIP trunk with a local phone number.  Unfortunately, Vianet, my local provider, is not one of the templates.

Vianet provided me with an IP address of their server and said I do not require a username or password because I too have a static IP.  They said all I have to do is send my trunk to their static IP.

I tried to edit /usr/pluto/bin/create_amp_vianet.pl but I couldn't make enough sense out of it.

I am hoping someone could give me a little direction on how to set up a SIP trunk to point to a static IP address that does not require a username or password.

Thank-you in advance,

Steven

Pages: [1]